RCA RT2910 User Manual

www.RCAav.com
Printed in China

Important Safety Instructions

Please read and save for future reference. • Unplug this apparatus during lightning storms
Some of the following information may not apply or when unused for long periods of time.
to your particular product; however, as with • R e fe r a l l s e r v i c i n g to q u a l i f i e d s e r v i ce
any electronic product, precautions should be personnel. Servicing is required when the
observed during handling and use. apparatus has been damaged in any way, such
• Read these instructions. as the power cord or plug is damaged, liquid
• Keep these instructions. has been spilled or objects have fallen into the
•
Heed all warnings. apparatus, the apparatus has been exposed to
• Follow all instructions. rain or moisture, does not operate normally, or
• Do not use this apparatus near water. has been dropped.
• Clean only with a dry cloth.
Additional safety information
• Do not block any ventilation openings.
• Apparatus shall not be exposed to dripping or
Install in accordance with the manufacturer's
splashing and no objects filled with liquids, such
instructions.
as vases, shall be placed on the apparatus.
• Do not install near any heat sources such
• Always leave sufficient space around the product
as radiators, heat registers, stoves, or other
for ventilation. Do not place product in or on a bed,
apparatus (Including amplifiers) that produce
rug, in a bookcase or cabinet that may prevent air
heat.
flow through vent openings.
• Do not defeat the safety purpose of the
• Do not place lighted candles, cigarettes, cigars,
polarized or grounding-type plug. A polarized
etc. on the product.
plug has two blades with one wider than the
• Connect power cord only to AC power source as
other. A grounding type plug has two blades
marked on the product.
and a third grounding prong. The wide blade
• Care should be taken so that objects do not fall
or the third prong is provided for your safety.
into the product.
If the provided plug does not fit into your wall
• Do not attempt to disassemble the cabinet. This
outlet, consult an electrician for replacement of
product does not contain customer serviceable
the obsolete outlet.
components.
• Protect the power cord from being walked on
or pinched particularly at plugs, convenience
If your product operates on batteries, adhere to
receptacles, and the point where they exit from
the following precautions:
the apparatus.
A. Any battery may leak electrolyte if mixed with a
• Only use attachments / accessories specified by
different battery type, inserted incorrectly, or if
the manufacturer.
all batteries are not replaced at the same time.
• Use only with a cart, stand, tripod, bracket or
B. Any battery may leak electrolyte or explode if
table specified by the manufacturer, or sold with
disposed of in fire or an attempt is made to charge
the apparatus. When a cart is used, use caution
a battery not intended to be recharged.
when moving the cart / apparatus combination
C. Discard leaky batteries immediately. Leaking
to avoid injury from tip-over.
batteries can cause skin burns or other personal
injury. When discarding batteries, be sure to
]
dispose of them in a proper manner, according
to your state / provincial and local regulations.
D. Battery shall not be exposed to excessive heat
such as sunshine, fire or the like.
Portable Cart
Warning
- 3 -
Connections and Setup
AM Loop Antenna and FM Indoor Antenna
1. Uncoil the antenna wire and locate the base end of the AM antenna.
2. Press down on the antennas tab to open the terminal.
3. Insert the antenna wires into the terminal and release the tabs to secure the wires in place.
4. Make sure the white wire on the AM loop antenna is inserted into the AM loop terminal and the other
wire is inserted into the ground loop terminal.
Connecting the speakers
Speaker wires are color-coded to match the terminals. Connect the speaker wire from the back of each
speaker to the corresponding color terminal at the back of the unit. Press down the tab to open the
terminal and insert the wire. Release the tab to lock wire in the terminal.
When connecting the speakers, make sure the polarities ("+" speaker wire to "+" on the unit. For example,
red wire to red terminal on the unit) of speaker wires and terminals match.
If the cords are reversed, the sound will be distorted. Do not let the speaker wires touch each other, it will
damage the Home Theater's amplifier.
Front Speakers
Center
Speaker
Right Left
Subwoofer
Purple and Black
Blue and Black
Grey and Black
Right Left
Rear Speakers
(Surround Sound)
- 7 -
It's important to read this instruction prior to using your new product for the first time.
811-AV6291W130
Connections and Setup
• One main unit Setup and Maintenance of the Unit
• One remote control with batteries
Provides spaces for sufficient ventilation as
• One p air o f f ront s peakers, o ne p air o f r ear s peakers,
indicated:
one center speaker and one subwoofer
• One pig-tail antenna wire
• One AM loop antenna
• One coaxial digital cable
• One pair of audio cable for analog connections
• One English, one French & one Spanish user manuals
• One English, French & Spanish quick start guides
• Do not connect to the AC power cords until all
Left and right Left and right
connections are completed.
front speakers rear speakers
• Do n ot u se y our s et i mmediately a fter t ransferring
it from a cold place to a warm place: there is risk
of condensation.
• Do not expose your set to water and excessively
high temperatures.
Center speaker • After having disconnected your set, clean the
case with a soft cloth, or with a slightly damp
leather chamois. Never using strong solvents.
AM/FM GAME/LINE-IN BD
TV VCR DVD SAT/CAB
SOURCE
Protect your Components from
RCR192A B2
Remote
Coaxial digital Overheating
control with
cable
• Do not block ventilation holes in any component.
batteries
Arrange the components so that air can circulate
freely.
• Do not stack components directly on top of each
Pig-tail
other.
Audio cable for
antenna wire
• Do not place the unit near other components
analog connections
that generate heat such as heating vents.
• Allow adequate ventilation when placing your
components in a stand.
User Quick start
manual • Place an amplifier near the top shelf of the stand
guide
so heated air rising from it will not affect other
components. If you have a satellite receiver, you
AM loop antenna
should place it on the top shelf.
- 4 -
Connections and Setup
Positioning Speakers
Front Speaker Placement
For best results, follow the speaker placement
below.
3
1 Alignment
Align the center speaker evenly with (A) or slightly
behind (B) (the left and right speakers), but not
ahead of them.
2
1
4
3
Courtesy Dolby Laboratories
1. Left, Right (Front Speakers)
Front speakers carry primarily music and sound
effects.
2. Center
In surround mode, the center speaker carries most
of the dialog as well as music and effects.
It should be set between the left and right
speakers.
Angle
3. Surround (Rear Speakers)
Place the left and right speakers to form a 45-
The surround speakers' overall sound balance
degree angle with your favorite viewing position
should be as close as possible to the front speakers.
to duplicate the soundtrack mixer's perspective.
Proper placement is vital to establish an evenly
distributed sound field.
Height
4. Subwoofer
The three front speakers should be as close as
SUBWOOFER
AUDIO OUT A subwoofer is designed to reproduce powerful
possible to the same height. This often requires
low bass effects (explosions, the rumble of
Use this jack on
placing the center speaker directly on top (A) or
spaceships, etc.).
beneath (B) the TV set.
the rear panel
to connect an Magnetic Shielding
active subwoofer
Speakers placed less than two feet from the TV set
other than the must be magnetically shielded in order to prevent
picture distortion. Center speaker provided with
one supplied.
this unit is magnetically shielded to protect your
TV set.
- 8 -
FCC Information
User Manual
RT2910
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
FCC INFORMATION
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio / TV technician for help.
WARNING: Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
This class B digital apparatus meets all requirements of the Canadian Interference - Causing Equipment
Regulations.
The Shock Hazard Marking and Associated Graphical Symbol is provided on the bottom panel of unit.
Refer to the identification / rating label located on the back panel of your product for its proper
operating voltage.
IMPORTANT: The power cord can be unplugged to turn off the main power to the unit. It should also be
easily accessible in an emergency.
•
Leave sufficient space around the appliance to allow adequate ventilation: 10cm on either side and
at the back, as well as 7cm above it are ideal.
WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
Connections and Setup
Connecting to HDMI Components
Note: This product will play audio from HDMI-connected products
TV with HDMI Input
while also passing on the video signal to a HDMI-connected TV.
Blu-ray Disc Player
Connecting to Audio Components
Analog Audio
Signals
Digital Audio in Connection
Digital Input
Connect components, such as DVD players, Satellite receiver/Cable boxes, BD (Blu-ray Disc
capable of outputting Dolby Digital (Surround Sound) or standard PCM (Stereo) format digital signals.
Note: "Blu-ray Disc" is a trademark of Blu-ray Disc Association.
Connections and Setup
Better Surround Placement
Location
If possible, place surround speakers to either side of the listening area, not behind it.
Height
If space permits, install surround speakers 2-3 feet above viewers. This helps to minimize localization
effects.
Aiming
Aim surround speakers straight across the room, not down at viewers, to help create a more open, spacious
surround sound field.
Courtesy Dolby Laboratories
Courtesy Dolby Laboratories
Alternative Surround Placement
Rear wall
If rear wall mounting is the only choice, aim the speakers at each other (A), towards the front (B) or towards
the sidewalls (C, D).
Experiment with placement until sounds seem to surround you, rather than come from behind you.
A
No adjacent walls
Surround speakers can go on stands facing each other to approximate sidewall mounting (A), or to the
sides or rear of the viewing area, aimed upwards; they can go right on the floor, or preferably, a few feet
off the floor such as on end tables (B).
B
Courtesy Dolby Laboratories
FCC Information
THE LIGHTNING FLASH AND ARROWHEAD For Your Safety
WITHIN THE TRIANGLE IS A WARNING
The AC power plug is polarized (one blade is wider
SIGN ALERTING YOU OF "DANGEROUS
than the other) and only fits into AC power outlets
VOLTAGE" INSIDE THE PRODUCT.
one way. If the plug won't go into the outlet
completely, turn the plug over and try to insert it
THE EXCLAMATION POINT WITHIN THE
the other way.
TRIANGLE IS A WARNING SIGN ALERTING
If it still won't fit, contact a qualified electrician to
YOU OF IMPORTANT INSTRUCTIONS
change the outlet, or use a different one. Do not
ACCOMPANYING THE PRODUCT.
attempt to bypass this safety feature.
CAUTION:
• To prevent electric shock, match wide blade of
plug to wide slot, fully insert.
• The apparatus shall not be exposed to dripping
or splashing and that no objects filled with
liquids, such as vases, shall be placed on
apparatus.
• The mains plug is used as disconnect device.
The mains plug of apparatus should not be
obstructed OR should be easily accessed during
intended use. To be completely disconnect the
power input, the mains plug of apparatus shall
be disconnected from the mains.
Service Information
This product should be serviced only by those
specially trained
techniques. For instructions on how to obtain
service, refer to the warranty included in this user
manual.
Connecting for Power
Make sure you connect all your other electronic
components and the speakers before plugging
your unit into the outlet. Plug the power cord in
the wall outlet, matching the wide blade of the
plug with the wide slot in the outlet. Be sure to
insert the plug completely.
- 1 -
Connections and Setup
Digital Connection
The digital audio jacks can accept Dolby Digital (Surround Sound) or PCM (Stereo) signals when
compatible components are connected.
• This unit provides one optical and one coaxial digital input jacks for the connection of your
components that have digital audio outputs.
• To connect DVD player, Satellite receiver, Cable box, Blu-ray player or TV that has a digital audio
output, use a coaxial digital (included) or an optical digital cable (not included) to carry the audio
Satellite Receiver or Cable Box
signal and enjoy Dolby Digital sound quality.
• A separate optical or coaxial cable is needed for each digital connection.
Notes: • If your TV has digital audio output, you can connect it to the corresponding digital
audio input of the system instead of using analog connection.
ANALOG AUDIO IN
• Optical and coaxial cables carry only the audio portion of the signal.
Analog Audio
Signals
Connecting the Antennas
Connect the AM and FM antennas to the AM and FM terminals on the system's back panel.
They must be hooked up in order to receive clear reception. For FM reception, extend antenna to its full
length. For AM reception, rotate the antenna horizontally to get better reception.
TM ) players or TVs,
- 5 -
Unit Controls
Main Unit
1
2
3
1. / (TUNING buttons)
Tunes in to desired stations in AM/FM mode.
2. ON/STANDBY
Turns on / off the unit. When the unit is turned on, the unit will go to the mode it was in before powered
off.
3. / (PRESET buttons)
Selects preset stations in AM/FM mode;
Selects item to be set in SETUP MENU.
4. GAME jacks
Connects game consoles or other AV products that have AUX audio outputs.
5. LINE IN
Connects portable audio devices or other AV products that have a LINE-OUT jack.
6. / (SURROUND buttons)
Selects among digital surround sound effects. (HALL, CHURCH, CLUB, STADIUM, STUDIO, STEREO, DOLBY
PL EMULATION, DOLBY PL II MUSIC, DOLBY PL II MOVIE) depending on input signal.
Adjusts value in SETUP MENU.
7. DVD, TV, SAT-CABLE, AM/FM, VCR, BD and GAME/LINE-IN (SOURCE buttons)
Selects sound source.
Courtesy Dolby Laboratories
8. Headphone jack
9. MASTER VOLUME
Adjusts the volume.
10. SETUP
Enters or quits the SETUP menu.
- 9 -
Technical Specification
Product: Dolby Digital Audio / Video Receiver
Brand: RCA
Electrical Consumption
Power Supply: 120V ~ 60Hz
This class B digital apparatus complies
with Canadian ICES-003.
Cet appareil numérique de la classe B
est conforme à la norme NMB-003 du
Canada.
This Home Theater has earned
the ENERGY STAR.
Headset Safety
• Do not play your headset at a high volume.
Hearing experts warn against extended high-
volume play.
•
If you experience a ringing in your ears, reduce
volume or discontinue use.
• You should use extreme caution or temporarily
discontinue use in potentially hazardous
situations.
• Even if your headset is an open-air type
designed to let you hear outside sounds, don't
turn up the volume so high that you are unable
in appropriate servicing
to hear what is around you.
•
Excessive sound pressure from earphones and
headphone can cause hearing loss.
- 2 -
BD/DVD/SAT-CABLE/TV/GAME
Optical Digital In (Audio)
Connect to optical digital output of Cable box, Satellite receiver, DVD, Blu-ray player,
TV or other compatible devices using the Optical Fiber Cable (not included).
Coaxial Digital In (Audio)
Connect to coaxial digital output of DVD, Cable box, Satellite
DVD player
receiver, TV or other compatible devices using the Coaxial Digital
Cable (included).
BD/DVD/SAT-CABLE/TV/GAME
FM
- 6 -
4 5 6 7 8
- 10 -
10
9