Table of Contents
Advertisement
Other
Information
Troubleshooting
No picture,
no sound but TV is on
•
Mayi_e
tile
cable/air
setting
is set
to the
_,'_rong
position.
,Se](.,c.'t GUIDE
Phts+
,_[_lttt
h'om
the
Main
ll/enu,
sele{.i
tilt. _'_c, tup option, and provide
tile correct information
on the follox\ing screens.
Go to pages 16 17 for detailed
instructions
•
The chalme{ might be empty
change channels.
If you're watching
your VCR and it's connected
with coaxial cahle to the CABLE/ANTENNA jack, tune the TV to channel 3 or 4
(whichever
channel
is selected on the 3/4 switch on the hack of your VCR). Also check to make sine the T_/VCR bunon on tile
VCR is in the correct mode (press the TV/VCR bumm on your VCR)
Sound okay, picture poor
•
Check
allt_.'0na
co[lnections.
Make
_ure
a[] of the
ca])les
a[-_ firnl]y
connected
to the
jacks.
•
"1"1"._ adjusting sharpness
function to improve weak signals. Go to page 47 for more instructions.
Black box appears on the screen
•
Closed captioning might be on, Check the Closed-Caption Displa) control panel in tile Screepl menu. Go to page 48 t_)rmore
instructions.
Every time I turn
on the TV, the Guide is on the screen
•
The GUIDE Plus+ system automatically
appears
on the screen when you use the TV button on the remote to turn on the TV. You
can turn off this feature by pressing GUIDE on your remote control and then select the Menu har. Press tile right arrow button to
select Setup• Choose Rezfiew optio*Ts and select OFF.
GUIDE Plus+ System
Problems
GUIDE Plus+ setup won't switch to channel 9 for VCR and/or channel 02 cable box
•
MaRe sure you have removed the Demo Pin from the G-LINKiack. Check to see if the G-LINK wands are positioned correctly in
front of components' remote _ensors.
GUIDE Plus+ system control of cable box is slower than direct control of the box itself. Keep this in mind when changing
channels•
You may have an incorrect
GUIDE Plus+ Channel Lineup. The guide may get out of sync with the cable provider,
Use the GUIDE
Plus+ Setup in the GUIDE Plus+ Menu to change the zip code to 99999. Turn the TV off for 10 minutes. Use Setup again to change
the zip code back to the correct value• If asked, be sure to select the correct channel lineup from the on screen list•
Program
information
doesn't
download
•
Review your setup information
and make sure it's correct. Press MENU on the remote and select GUIDE Plus+ Setup. Go to page 16
for detailed
instructions
abnut the GUIDE Plus+ Setup menus.
The TV must be oft to download
information.
Leave your TV off overnight,
for at least 10 hours, to receive the initial download
f_)r
your area.
If you're using a cable box, leave it on so you can receive program
information.
Scheduled
Watch or Record doesn't
occur
Check Schedule
for timer conflicts.
Go to page 50 for instructions.
Make sure the wands of the G-LINK cable are placed in front of the remote sensor(s)
on the component(s).
Make sure your ¥CR is turned
off during the time you've scheduled
to record a program
because
the system turns the VCR on when
it starts recording (if it's already on when recortling
Still'IS, the system will turn it off)
Make sure there is a tape in the VCR and that the VCR is connected
p_operly.
Be sure that you set up tile VCR in tile GUIDE' lqtts+ _S'etupmenus. If you don't complete
t!le Cb*g_wtri*l,_.fi)r (t I'CR steps
successfully,
tht' Record oplion \\ont
he avaitahle
Go t_ p. 18 R_I"detaited
instructions
If a cable box is attached to yc_tir "1_. r, make sure you set it up correttly
in tile G{,Jl)l:lqus+
S{,!zq_i//cnus. (}1) t(>p:tge 16 17 Ior
detailed
instructions
Chapter
5
53
Hide quick links:
Advertisement
Table of Contents
