Acer H6500 Service Manual
  1. Manuals
  2. Brands
  3. Acer Manuals
  4. Projector
  5. H6500 Series
  6. Service manual

Acer H6500 Service Manual

Hide thumbs Also See for H6500:
Table of Contents

Advertisement

Quick Links

See also: User Manual

SERVICE MANUAL

H6500
Date
Revise Version
Description
2011.09.14
V1.0
Initial Issue
Copyright September, 2011
All Rights Reserved
Alex
Prepared:
Checked:
Approved:

Advertisement

Table of Contents
loading

Related Manuals for Acer H6500

Summary of Contents for Acer H6500

  • Page 1: Service Manual

    SERVICE MANUAL H6500 Date Revise Version Description 2011.09.14 V1.0 Initial Issue Copyright September, 2011 All Rights Reserved Alex Prepared: Checked: Approved:...
  • Page 2 Preface This manual is applied to H6500 projection system. The manual gives you a brief description of basic technical information to help in service and maintain the product. Your customers will appreciate the quick response time when you immediately identify problems that occur with our products.

  • Page 3: Table Of Contents

    Re-write System and Lamp usage hour 2-21 Assemble Elevator foot rubber 2-22 Assemble Bottom shielding and IO cover module 2-22 Assemble Lamp driver module and Interrupt switch 2-23 Assemble LVPS module 2-25 Assemble System fan module and the Blower module 2-26 Confidential H6500...
  • Page 4 Function Test & Alignment Procedure Test Equipment Needed Service Mode OSD Reset Test Condition Test Inspection Procedure PC Mode Calibration Video Performance Optical Performance Measure 4-10 Others 4-12 Chapter 5 Firmware Upgrade Equipment Needed Get into Firmware download mode Confidential H6500...
  • Page 5 Setup Procedure (VGA & HDMI 1) EDID Key-In Procedure (VGA & HDMI 1) Setup Procedure ( HDMI 2) EDID Key-In Procedure ( HDMI 2) Un-lock SNID and Default Language Reset 6-10 Appendix A Exploded Overview Appendix B Serial Number System Definition PCBA Code Definition Confidential H6500...

  • Page 6: Chapter 1 Introduction

    ● F/ #: 2.55 (wide); 2.85(tele); 1.2x Mechanical Zoom Lens Projection lens (YM40Y) ● Engineering spec: • Typical 1800 ANS� Lumens (Bright/Full power/Wide mode) • Minimum 1600 ANS� Lumens ( Bright/Full power/Wide Brightness mode) ● Marketing spec: • Typical 1800 ANS� Lumens • Minimum 1600 ANS� Lumens H6500 Confidential...
  • Page 7 ● 1920(H) x 1080(V) ● 6 segments Color wheel ● 7200 rpm (2X) ● Segment Angle: �94Y46M33�93C22B72 Segment Angle: �94Y46M33�93C22B72 Lamp ● 240 Watt Osram E20.8 Lamp ● Standards : • NTSC (3.58/4.43) Video compatibility • PAL (B/D/�/H/�/M/N) • SECAM (B/D/�/K/K1/L) H6500 Confidential...
  • Page 8 • S-video Luminance 0.714Vp-p, 75 ohm • Chrominance 0.286Vp-p, 75 ohm • Component Video 1Vp-p, 75 ohm ● Operating: 5°C~ 35°C Temperature ● Storage: -20°C~ 60°C ● Operating: 5°C~ 35°C, 80%�H (Max.), Non-condensing Maximum Humidity ● Storage: -20°C~ 60°C, 80%�H (Max.), Non-condensing H6500 Confidential...

  • Page 9: Compatible Mode

    PowerBook G4 640x480 66.6(67) 34.9 PowerBook G4 800x600 37.9 PowerBook G4 1024x768 48.4 PowerBook G4 1152x870 68.7 PowerBook G4 1280x960 75.2 i Mac DV(G3) 1024x768 60.3 (2) V�A Analog - Extended Wide timing WXGA 1280x768 47.8 1280x768 60.3 H6500 Confidential...
  • Page 10 640x480 37.9 640x480 37.5 640x480 43.3 SVGA 800x600 35.1 800x600 37.9 800x600 48.1 800x600 46.9 800x600 53.7 1024x768 48.4 1024x768 56.5 1024x768 60.0 1024x768 68.7 SXGA 1152x864 63.8 1152x864 67.5 1152x864 77.1 1280x1024 64.0 1280x1024 77.0 1280x1024 80.0 H6500 Confidential...
  • Page 11 1280x720 37.5 1080i 1920x1080 60(30) 33.8 1080i 1920x1080 50(25) 28.1 1080p 1920x1080 67.5 1080p 1920x1080 56.3 Horizontal scan 30k-100kHz �raphic source moni- rate: tor range limits Vertical scan rate: 50-85Hz Max. pixel rate 170MHz TMDS Max. frequency 200Mhz H6500 Confidential...

  • Page 12: Product Overview

    1-3 Product Overview Projector Outlook Front /Upper side Item Description Item Description Control panel Zoom lever Ventilation (inlet) �emote control receivers Ventilation (outlet) Focus ring Elevator button Zoom lens Elevator foot Lens cap H6500 Confidential...

  • Page 13: Rear Side

    Rear side Item Description Item Description Power socket HDM� 1 connector USB Ctrl connector HDM� 2 connector PC analog signal/HDTV/component 12V DC output connector video input connector (V�A �N) YPbPr/YCbCr input connector Kensington™ lock port Composite video input connector H6500 Confidential...

  • Page 14: Control Panel

    Temp �ndicator LED Use to select items or make adjustments to Four directional select keys your selection. SOU�CE Changes the active source. Unique Acer functions: eOpening, eView, eTimer, ePower Empowering key Management. �emote controlreceiver �eceives signals from remote control. H6500 Confidential...
  • Page 15 Remote Control Layout H6500 Confidential 1-10...
  • Page 16 �efer to the “Turning the Projector On/Off�� section. ASPECT �AT�O To choose the desired aspect ratio (Auto/4:3/16:9/L.Box) ZOOM Zooms the projector display in or out. Unique Acer functions: eView, eTimer, ePower Manage- Empowering key ment. Adjusts the image to compensate for distortion caused KEYSTONE tilting the projector (±...
  • Page 17 MUTE No function. W��ELESS No function. Press “0~9�� to input a password in the “Security KeyPad 0~9 settings��. Four directional Use up, down, left, right buttons to select items or make select keys adjustments to your selection. H6500 Confidential 1-12...

  • Page 18: Getting Started

    Composite video cable V�A cable HDM� cable V�A to component/HDTV adapter 12 DC Cable Note: To ensure the projector works well with your computer, please make sure the timing of the display mode is compatible with the projector. H6500 Confidential 1-13...
  • Page 19 System Block Diagram H6500 Confidential 1-14...
  • Page 20 Bottom Cover Dimension H6500 Confidential 1-15...

  • Page 21: Disassembly Process & Assembly Process

    * Before you start: This process is protective level II. Operators should wear electrostatic chains. * Note: - If you need to replace the Main Board, you have to get into Service Mode and record the lamp usage hour, please refer to section 2-16. H6500 Confidential...

  • Page 22: Disassemble Lamp Module

    (as yellow arrows) on the left/right side of the projector. 3. Pull upward the Lamp cover module (as blue arrows point). 4. Loosen 2 screws (as red circle) on the Lamp module. 5. Take off the Lamp module. H6500 Confidential...

  • Page 23: Disassemble Top Cover Module

    Note: - When you disassemble the Top cover, take care the FPC cable which connect Main board and Keypad board module. 3. Unplug 1 connector (as green square) from the Main board module. 4. Disassemble the Top cover module. H6500 Confidential...

  • Page 24: Disassemble Keypad Board And Zoom Ring

    Please detach the Circuit boards and follow local regulations for disposal. Keypad board module Keypad module 3. Unscrew 3 screws (as yellow circle) to disassemble the Zoom ring module. Zoom ring module Top cover module H6500 Confidential...

  • Page 25: Disassemble Main Board Module

    1. Unscrew 7 screws (as red circle) to disassemble the Main board top shielding. 2. Unscrew 2 hex screws (as green circle). 3. Unscrew 3 screws (as pink circle) and 1 hex screw (as yellow circle). 4. Cut down 1 cable tie (as red square). H6500 Confidential...
  • Page 26 Compose of White/Black/Red Photo sensor (J16) wire, Green connector and Gray wire tube (3 pin) Compose of Red/White/Black Blower (J8) wire, White connector and Blue wire tube (3 pin) Compose of Red/Yellow/Black System Fan (J9) wire, White connector (3 pin) H6500 Confidential...
  • Page 27 (16 pin) 7. Disassemble Main board module. Main board module NOTE: Circuit boards > 10 cm² has been highlighted with the yellow rectangle as above image shows. Please detach the Circuit boards and follow local regulations for disposal. H6500 Confidential...

  • Page 28: Disassemble Front Cover Module

    2. Open 2 clips (as yellow square). 3. Disassemble the Front cover module. 4. Tear off 1 black mylar (as green square) form IR board. 5. Separate IR sensor board and Front cover module. Front cover module IR sensor board H6500 Confidential...

  • Page 29: Disassemble Color Wheel Module

    3. Unscrew 1 screw (as green circle). 4. Separate the Photo sensor board, Photo sensor board cover and Color wheel module. Note: - Avoid touching the glass parts of Color wheel. Color wheel module Photo sensor board Photo sensor board cover H6500 Confidential...

  • Page 30: Disassemble Engine Module

    2. Take off the Main broad spacer (as red circle). 3. Remove Focus ring (as red arrow). Main Broad Focus ring Spacer 2-9 Disassemble DMD chip and DMD board 1. Tear off the 2 black heatsink mylar (as red square). H6500 Confidential 2-0...
  • Page 31 DMD Chip. DMD chip DMD board module NOTE: Circuit boards > 10 cm² has been highlighted with the yellow rectangle as above image shows. Please detach the Circuit boards and follow local regulations for disposal. H6500 Confidential 2-...

  • Page 32: Disassemble System Fan Module And The Blower Module

    Blower module 1. Unplug 1 connector on LVPS module (as yellow square). 2. Cut down 1 cable tie (as yellow circle). 3. Unscrew 3 screws (as red circle) to disassemble System Fan Module. H6500 Confidential 2-2...
  • Page 33 5. Unscrew 4 screws (as red circle) to separate System Fan and Fan Shielding. 6. Unscrew 1 screws (as green circle) to separate Thermal switch and Fan shielding module. 7. Seprate Blower bracket and Fan shielding. Fan shielding System Fan Blower bracket Thermal switch H6500 Confidential 2-...
  • Page 34 Note: - Take the Fan Module as the right gesture. the right gesture the wrong gesture 8. Unscrew 3 screws (as yellow circle) to disassemble the Blower module. 9. Separate the Blower rubber and the Blower. Blower rubber Blower H6500 Confidential 2-...

  • Page 35: Disassemble Lvps Module

    4. Remove the LVPS module and 1 black mylar. NOTE: Circuit boards > 10 cm² has been highlighted with the yellow rectangle AC Inlet Bracket as above image shows. Please detach the Circuit boards and follow local regulations for disposal. H6500 Confidential 2-5...

  • Page 36: Disassemble Lamp Driver Module And Interrupt Switch

    3. Unplug 2 connectors (as pink square). 4. Unscrew 2 screws (as blue circle) and unfasten 2 tenons (as yellow square) 5. Unplug 1 Lamp cable (as green square) to separate Lamp driver and Lamp driver holder. H6500 Confidential 2-6...
  • Page 37 1 black mylar (as red square) to remove the Lamp cable. NOTE: Circuit boards > 10 cm² has been highlighted with the yellow rectangle as above image shows. Please detach the Circuit boards and follow local regulations for disposal. H6500 Confidential 2-17...

  • Page 38: Disassemble Bottom Shielding And Io Cover Module

    IO cover module 1. Unscrew 2 screws (as red circle) and tear off 1 black mylar (as red square) to disassemble bottom shielding. 2. Unfasten 2 tenons (as green rectangle) to disassemble IO cover module. H6500 Confidential 2-18...

  • Page 39: Disassemble Elevator Foot Rubber

    2-14 Disassemble Elevator foot rubber 1. Turn over the bottom cover, then take off the Elevator Foot Rubber (as red rectangle). H6500 Confidential 2-19...

  • Page 40: Rod Adjustment

    - It should not have any abnormal color at the frame of the image by estimating through the eyes. Note: - Avoid over adjusting the rod. - After the opreation, please use the glue to fix the screws. H6500 Confidential 2-20...

  • Page 41: Re-Write System And Lamp Usage Hour

    "Right" buttons to re-write the Lamp Hours. 5. Exit Service Mode - Use "Up" or "Down" buttons to select "Exit", press "Menu" button to exit the Service Mode. Note: left key = decrease System/Lamp hour right key =increase System/Lamp hour H6500 Confidential 2-2...

  • Page 42: Assemble Bottom Shielding And Io Cover Module

    2-17 Assemble Elevator Elevator foot rubber 1. Assemble the Elevator foot rubber (as red rectangle). 2-18 Assemble Bottom shielding and IO cover module 1. Fasten 2 tenons (as green rectangle) to assemble IO cover. H6500 Confidential 2-22...

  • Page 43: Assemble Lamp Driver Module And Interrupt Switch

    2. Screw 2 screws (as green circle) and stick 1 black mylar (as red square) to assemble bottom shielding. 2-19 Assemble Lamp driver module and Interrupt switch 1. Screw 1 screw (as red circle) to assemble the lamp cable to Lamp driver holder. H6500 Confidential 2-2...
  • Page 44 Lamp driver. 5. Plug 2 connectors (as red square). 6. Screw 1 screw (as green circle) to assemble the Lamp driver module. 7. Fasten 1 tenon(as blue circle) to assemble the Interrupt switch. H6500 Confidential 2-2...

  • Page 45: Assemble Lvps Module

    1. Fixed 1 black mylar and the LVPS module on the bottom module. AC Inlet Bracket 2. Fixed the AC Inlet Bracket on LVPS module. 3. Screw 6 screws (as red circle) to assemble the LVPS module. 4. Plug 3 connector (as green square). H6500 Confidential 2-25...

  • Page 46: Assemble System Fan Module And The Blower Module

    2. Screw 3 screws (as yellow circle) to assemble the Blower module. 3. Assemble Blower bracket and Fan shielding. 4. Screw 1 screws (as red circle) to Fan shielding System Fan assemble Thermal switch and Fan shielding module. Blower bracket Thermal switch H6500 Confidential 2-26...
  • Page 47 5. Screw 4 screws (as green circle) to assemble System fan and Fan shielding. 6. Screw 4 screws (as red circle) to assemble System Fan Module. 7. Use a cable tie to fix Blower and System fan cable (as yellow circle). H6500 Confidential 2-27...

  • Page 48: Assemble Dmd Chip And Dmd Board

    2. Assemble the Heat Sink and DMD Module. Heat sink DMD heat sink rubber DMD broad module and DMD rubber DMD mask DMD chip 3. Screw 4 screws (as blue circle). 4. Stick the 2 black heatsink mylar (as red square). H6500 Confidential 2-28...

  • Page 49: Assemble Engine Module

    Engine Module. 2-24 Assemble Color wheel module Photo sensor board Photo sensor board cover 1. Assemble the Photo sensor board, Photo sensor cover and Color wheel. Color wheel module 2. Screw 1 screw (as green circle). H6500 Confidential 2-29...
  • Page 50 Note: - Avoid touching the glass parts of Color Wheel. 2-25 Assemble Front cover module IR sensor board 1. Assemble IR Board on Front Cover. 2. Stick 1 black mylar (as yellow square) on IR Board. Front cover module H6500 Confidential 2-0...

  • Page 51: Assemble Front Cover Module

    1. Plug 1 connectors (as green rectangle) 2. Assemble Main board to DMD board. 3. Plug 6 connectors (as yellow rectangle). 4. Use 1 cable tie to fix the Interrupt cable and Lamp driver cable (as red circle). H6500 Confidential 2-...
  • Page 52 5. Screw 3 screws (as red circle) and 1 hex screw (as yellow circle). 6. Screw 2 hex screws (as green circle). 7. Screw 7 screws (as green circle) to assemble the Main board top shielding. H6500 Confidential 2-2...

  • Page 53: Assemble Keypad Board And Zoom Ring

    1. Screw 3 screws (as yellow circle) to assemble the Zoom ring module. 2. Assemble the Keypad board module and the Keypad module. 3. Screw 4 screws (as red circle) to assemble the Keypad board module. Keypad board module Keypad module H6500 Confidential 2-...

  • Page 54: Assemble Top Cover Module

    2-28 Assemble Top cover module 1. Plug the connector (as green square) to Main board module. 2. Pull downward the top cover module. 3. Screw 9 screws (as red circle) on the top cover. H6500 Confidential 2-...

  • Page 55: Assemble Lamp Module

    2. Screw 2 screws (as red circle) on the Lamp module. 3.Pull downward the Lamp cover module (as blue arrows point). 4. Push backward the Lamp cover moudle (as yellow arrows ). 5. Screw 2 screw (as yellow circle) to fixed the top cover. H6500 Confidential 2-5...

  • Page 56: Chapter 3 Troubleshooting

    Fan lock error OSD shows H(On), 0.5 red “Fan Fail, Will auto- second L(Off) matically turn off soon” flashing Lamp error (Lamp, ballast) 0.5 second H(ON), 0.5 Color Wheel fail second L(OFF) flashing Note: Steady Light: "ON" No Light: "--" H6500 Confidential...

  • Page 57: Main Procedure

    - Ensure all connectors are securely connected and aren’t broken - Check Lamp Cover - Check Interrupt Switch - Check Lamp Module - Check Lamp Driver No Light On - Check LVPS - Check Main Board - Check Color Wheel - Check Photo Sensor Board H6500 Confidential...
  • Page 58 - Ensure that the signal cables and sources work well - Check Lamp Driver - Check Waveform has been downloaded - Check Lamp Module Image Flicker - Check Color Wheel - Check Photo Sensor - Check DMD Board - Check Main Board H6500 Confidential...
  • Page 59 Check Battery b. Check Remote Controller c. IR receiver d. Check IR Sensor Board Remote Con- troller/Control e. Check Main Board Panel Failed - Control Panel a. Check FPC cable b. Check Keypad Board c. Check Main Board H6500 Confidential...
  • Page 60 Universal Password: " " (1) Click the AcerSNID (2) Input SNID number. (SNID number is on the Security Card) Forgetting Pass- word (adminis- trator Password) " " (3) Click Calculate . Then the Universal Password will appear. H6500 Confidential...
  • Page 61 Service Mode to obtain the SNID number, then calculate the Universal Password. - Ensure that the signal cables and PC works well - Check the software program version FW Upgrade - Check the firmware file Failed - Check the upgrade process - Check Main Board H6500 Confidential...

  • Page 62: Function Test & Alignment Procedure

    1. After final QC step, we have to erase all saved change again and restore the OSD default setting. The following actions will allow you to erase all end-users' settings and restore the default setting: (1) Please get into OSD menu. (2) To execute "Reset" function. H6500 Confidential...

  • Page 63: Test Condition

    A+B = 0 4-4-2 Burn-In Test - Temperature: 15°C~35°C - Circumstance brightness: Normal environment - Screen size: No concern - Display mode: ECO mode - After repairing each unit, it should be Run-in (refer to the below table). H6500 Confidential...

  • Page 64: Test Inspection Procedure

    OSD Reset EDID Re-write Lamp Hour Usage Reset Default Language Rod adjustment Waveform Download Restore Fan Speed Note: - After changing parts, check the information above table. - The Default Language and Waveform Download are the same method. H6500 Confidential...

  • Page 65: Pc Mode

    - Test equipment: video generator - Test signal: 1�20 x 1080 �60Hz 1�20 x 1080 �60Hz - Test Pattern: Full black Inspection item - Bright pixel check Criteria - Bright pixel is unacceptable in the active zone, Full black H6500 Confidential...
  • Page 66 - Test signal: 1�20 x 1080 �60Hz 1�20 x 1080 �60Hz - Test Pattern: Blue 60 Inspection item - Dark blemish check Criteria - The dark blemish should be no more than 10 under blue 60 pattern. Blue 60 - Ref. Defect specification table H6500 Confidential...
  • Page 67 (The unidentified color levels on both left and right sides should not over 4 color levels.) - Gray level should not have abnormal color or heavy lines. SMPTE BAR - If color appears abnormal, please get into service mode to do color wheel index adjustment. H6500 Confidential...

  • Page 68: Calibration

    - Test equipment: video generator - Once Main Board is changed. Video Calibration should be done as well. (1) Test signal: 720p �60Hz �60Hz (2) Test Pattern: SMPTEbar - Note (1) Calibration pattern should be in full screen mode. SMPTE BAR H6500 Confidential...
  • Page 69 - There should not have any lack of SMPTE BAR. Master - The screen appears normal, it shouldn’t appear any abnormal condition, such as lines and so on. - It is unacceptable that the color appears abnormal and flashing. H6500 Confidential...

  • Page 70: Video Performance

    - Check abnormal color, line distortion or noise on the screen. - Check the sound from speaker. 4. Audio Test Procedure - Test equipment: DVD player - Test signal: CVBS Inspection item - Audio performance test Inspection Distance - 1.8M ~2.5M H6500 Confidential 4-�...

  • Page 71: Optical Performance Measure

    OSD mode, the settings are as below: - "Display mode" is "Bright", "Brightness" is "50", the "Format" is "16:�", and "ECO Mode" is "Off". 2. Brightness Procedure - Full white pattern - Use CL100 to measure brightness values of Full white pattern H6500 Confidential 4-0...
  • Page 72 - Full white pattern - Use CL100 to measure brightness values of P1~P� (see image: full white). - Follow the Uniformity formula to calculate average values. ☼ Uniformity Formula JBMA Uniformity = Avg. (P1, P3, P7, P�)/P5X100% Criteria • 65% H6500 Confidential 4-...

  • Page 73: Others

    It should be locked in the correct place. Plastic Parts All plastic parts can not be broken and damaged. Safety or warning All safety and warning labels should be visible, label including all contents. All interface connectors should be complete and Connector workable. H6500 Confidential 4-12...

  • Page 74: Firmware Upgrade

    Chapter 5 Firmware Upgrade 5-1 Equipment Needed Software : - UsbDriver.zip - H6500_MB_FW_xxx Note: ''xxx'' represent software version. Hardware : - Projector - Power Cord: 42.50115G001 - Mini USB Cable: 42.00286G101 - PC or Laptop H6500 Confidential...

  • Page 75: Get Into Firmware Download Mode

    Note: - The system fan and the lamp will not operate. Power port 5-3 Install USB driver - Execute Program (1) "Found New Hardware Wizard" picture will appear on the screen. (2) Select "Install the software automatically (Recommended)". (3) Click "Next". (4) Wait for several seconds. H6500 Confidential...
  • Page 76 (5) Click "Continue Anyway". (6) Click "Browse". (7) Select the file "pwusbio.sys", then open it. (8) Click "OK". H6500 Confidential...

  • Page 77: Firmware Upgrade Procedure

    (9) Click "Finish", - The USB Driver has finished installation. 5-4 Firmware upgrade procedure 1. Double click the folder "H6500_MB_FW_xxx''. 2. Execute "FlashUpgrader.exe". H6500 Confidential...
  • Page 78 4. The Firmware upgrade procedure will run automatically. 5. Finish - When message "Flash Completed" appears, click "OK", then click "Close". 6. Check FW version. (To get into Service Mode, please press "Power", "Left", "Left" and "Menu" buttons sequentially.) H6500 Confidential...

  • Page 79: Waveform Download

    Note: - If the "Factory Fan Speed" is a negative number (as picture B shows), it means that the procedure is failure, please do above steps again. - This step must be executed after changing Firmware, Main board or Lamp blower. H6500 Confidential...

  • Page 80: Edid Upgrade

    Note: - If a display device has digital input ports, like DVI or HDMI, but without EDID in its Main Board, the display device will show no image while the input source is digital signal. - After EDID upgrading, please execute "Default Language Reset". H6500 Confidential...

  • Page 81: Equipment Needed

    - VGA Cable (42.87305G102) - HDMI(M) to DVI(F) Adapter (42.82B13G001) - DVI Cable (42.83N06G001) - Generic Fixture (80.00001.001) for EDID Key-in - RS-232 9 Pin Cable (pin to pin, F-M) (42.83C07G001) - Power Adapter (47.57803G001) - Monitor - PC H6500 Confidential...

  • Page 82: Enter Edid Firmware Mode

    HD�I��� To (4) Plug Power Adapter to P4 of fixture. D�I�F� ��dapter ���� IN Port (5) Plug Power Cord to projector. D�I Power Cable Note: - You must confirm that the JP3 is closed in Cable all procedure. H6500 Confidential...

  • Page 83: Edid Key-In Procedure (Vga & Hdmi 1)

    (3) Select the EDID file (*-HDMI1.ini). (4) Click "Open". �3� �4� (5) Key in the Serial Number into the �5� Barcode blank space. �7� (6) In "Write Source Select" item, select "VGA" and "HDMI 1". �6� (7) Click "Program". H6500 Confidential...
  • Page 84 VGA" appears on the screen, click "OK". 4. - When the message "Please change the cable to HDMI" appears on the screen, click "OK". 5. When the EDID program is completed, a message "OK" will appear on the screen. H6500 Confidential...
  • Page 85 "Trans", then click the "Read". - EDID "Analog" information will show the result. 7. Read EDID "Digital" information - In "Read item", select "Digital" and "Trans", then click the "Read". - EDID "Digital" information will show the result. H6500 Confidential...

  • Page 86: Setup Procedure ( Hdmi 2)

    ��dapter (3) Plug Power Adapter to P4 of fixture. (4) Plug Power Cord to projector. Note: - You must confirm that the JP3 is closed in all procedure. HD�I��� To D�I�F� ��dapter HD�I2 Port Power D�I Cable Cable H6500 Confidential...
  • Page 87 �1� (3) Select the EDID file (*-HDMI2.ini). (4) Click "Open". �3� �4� (5) Key in the Serial Number into the Barcode blank space. �5� (6) In "Write Source Select" item, select "HDMI 2". �7� (7) Click "Program". �6� H6500 Confidential...
  • Page 88 4. When the EDID program is completed, a message "OK" will appear on the screen. 5. Read EDID "HDMI2" information - In "Read item", select "Digital" and "Trans", then click the "Read". - EDID "HDMI2" information will show the result. H6500 Confidential...

  • Page 89: Un-Lock Snid And Default Language Reset

    Note: If it is fail, please do the actions as above steps. S/N General rule: Use the last 1 digit code (as red word) for language information Language Code (F) Default Language English Thailand Japan Russian Germany Hungarian H6500 Confidential 6-0...
  • Page 90 Appendix A (Exploded Image) Note: This chapter is only designed to show the exploded image of the projector. For updated part numbers, please refer to RSPL report. D.C. H6500 Confidential...
  • Page 91 Description supply 35.87U03G001 LAMP WARNING LABEL P5260 51.8GF20G001 MYLAR FOR ELEVATOR 8GF P1100 75.8GF05G011 ASSY LAMP DOOR MODULE 8ML H6500 61.8GF02H011 TOP SHIELDING SECC 0.5T FOR H6500 70.8ML01G001 ASSY BOTTOM HOUSING MODULE H6500 70.8ML13G001 ASSY FRONT COVER MODULE 8ML H6500 70.8ML08GR01...
  • Page 92 LAMP DRIVER HOLDER P1100 51.81541G001 TAPE 3M J350 17*30mm 75.87U02G001 ASSY INTERRUPTER SWITCH P5260 L=280MM ASSY OSRAM LAMPDRIVER PT VIP O3 MID 240W- 75.8ML02G011 UNIPRO AS WITH DYNAMIC ECO 85.0A123G050 SCREW P/F MECH M3*5 Ni 85.3A122G040 SCREW CAP MECH M2*4 Ni H6500 Confidential...
  • Page 93 ASSY FAN MODULE Parts Item Description supply 49.8GG01G001 SUNON 80*25MM AXIAL FAN 52.8BA05G001 LAMP BLOWER RUBBER P1266 61.8GF03H001 FAN SHIELDING SECC 0.5T FOR 8GF P1100 85.1A323G080 SCREW PAN MECH M3*8 BLACK “GREEN” H6500 Confidential...
  • Page 94 ASSY ENGINE MODULE H6500 Confidential...
  • Page 95 ASSY ROD MODULE HD20 70.8ML19G001 ASSY ENGINE BASE H6500 70.8ML11G001 ASSY COLOR WHEEL MODULE H6500 70.8ML03GR01 ASSY COLOR WHEEL MODULE H6500 (SERVICE) PCBA PHOTO SENSOR BOARD FOR H9500BD PRO- 80.8JY04G001 JECTOR PCBA PHOTO SENSOR BOARD FOR H9500BD PRO- 80.8ML02G002 JECTOR 85.1A526G060...
  • Page 96 ASSY BOTTOM HOUSING MODULE H6500 Confidential...
  • Page 97 51.8ML01H001 FOCUS RING PC MN3600H H6500 61.8ML04G001 HEX SCREW M3*H=6,M2.6*L=7 70.8ML03G001 ASSY LAMP DRIVER MODULE H6500 70.8ML09G001 ASSY SYSTEM FAN MODULE 8ML H6500 70.8ML04G001 ASSY OPTICAL ENGINE MODULE H6500 70.8ML05GR01 ASSY ENGINE MODULE H6500(SERVICE) 70.8ML05G001 ASSY MAIN BOARD MODULE H6500 70.8ML06GR01...
  • Page 98 Parts Item Description supply 51.87H09G001 FRONT IR LENS XD1171D 51.8GF28G001 IR MYLAR FOR 8GF P1100 51.8GF03H011 FRONT COVER PC LN2520 H6500 70.8ML08GR01 ASSY FRONT COVER MODULE H6500(SERVICE) 61.8BA12G001 ACER LOGO P1266 80.8ML05G001 PCBA IR Board For H6500 PROJECTOR H6500 Confidential...
  • Page 99 ASSY BOTTOM COVER MODULE H6500 Confidential...
  • Page 100 86.00122G020 YH-NUT-M2.0*2.0*4.0 70.8ML15G001 ELEVATOR BRACKET P1266 75.8CT01G001 ASSY MATRITEK 230W LVPS FOR HORUS 75.8GF01G022 BUY ASSY BOTTOM COVER 8ML FOR H6500 70.8ML02GR01 ASSY BOTTOM COVER MODULE H6500 (SERVICE) 85.0A123G050 SCREW P/F MECH M3*5 Ni 85.5A126G040 SCREW BINDING MECH M2.6*4 Ni 85.1C123G060...
  • Page 101 TAPE 3M 1350B 8GF P1100 41.88003G001 EMI GASKET W9*H3*L35 35.87U03G001 LAMP WARNING LABEL P5260 75.8GF02G012 BUY ASSY TOP COVER MODULE H6500 80.8ML03G003 PCBA KEYPAD BD. FOR H6500 PROJECTOR 70.8ML01GR01 ASSY KEYPAD BOARD MODULE H6500 (SERVICE) 85.YA123G040 SCREW(TAPPING FLAT HEAD NI M3*4)-AD2022m...
  • Page 102 ASSY BLOWER MODULE Parts Item Description supply 49.8EF04G001 SUNON 45*20mm GB1245PKVX-8 F-TYPE BLOWER 52.82G08G001 BLOWER 4520 RUBBER EP7190 H6500 Confidential XIII...
  • Page 103 36.000A4H001 EMEA, SERVICE STATION CARD, ACER SERVICE STATION SHEET FOR EMACHINES TUR- 36.8ER05G001 36.8ML01H001 USER’S GUIDE MULTILINGUAL (CD) ACER H6500 36.8ML02H001 QUICK START CARD MULTILINGUAL ACER H6500 42.00200G005 CABLE VGA 15P 1.8M BLK EP739 INFRARED REMOTE CONTROLLER L7 WHITE WITH- 45.87U01G107...
  • Page 104 H6500 Confidential...
  • Page 105 55.8GF02G011 CARRY BOX FOR H6500 56.8BA02G001 AIR BAG BOTTOM P1266 56.8GF01G001 AIR BAG TOP P1100 58.8EE01G001 PALLET 1220*1020MM FOR ACER EMEA/AAP 58.87W01G001 COVER PALLET 1150*920*5mm P5270 75.8EE09H001 BUY ASSY LENS CAP H7530 70.8ML10GR01 ASSY LENS CAP MODULE H6500(SERVICE) H6500 Confidential...

  • Page 106: Fru List

    FRU list Category Coretronic P/N Part Name ACER part NO. Photo CASE/ COVER/ FRONT BRACK- 70.8ML08GR01 COVER 60.JD50H.005 ET AS- MODULE SEMBLY CASE/ COVER/ IO COVER BRACK- 70.8ML04GR01 60.JD50H.003 MODULE ET AS- SEMBLY DIGITAL LIGHT SP.8ML04GC01 LAMP EC.JD500.001 DEVICE CABLE LAMP CABLE 42.00422G001...
  • Page 107 Category Coretronic P/N Part Name ACER part NO. Photo 49.8GG01G001 23.JC70H.001 DIGITAL LIGHT 48.8MQ01G001 DMD CHIP 57.JD50H.001 DEVICE DIGITAL ENGINE LIGHT 70.8ML05GR01 57.JD50H.003 MODULE DEVICE DIGITAL COLOR LIGHT 70.8ML03GR01 57.JD50H.002 WHEEL DEVICE PHOTO BOARD 80.8JY04G001 SENSOR 55.JDG0H.002 BOARD 80.8ML02G002 55.JD50H.001...
  • Page 108 Category Coretronic P/N Part Name ACER part NO. Photo MANIN BOARD 70.8ML06GR01 BOARD 55.JD50H.004 P1100 CASE/ COVER/ BOTTOM BRACK- 70.8ML02GR01 60.JD50H.002 COVER ET AS- SEMBLY IR SENSOR BOARD 80.8ML05G001 55.JD50H.002 BOARD CABLE MB CABLE 42.00451G011 50.J690H.002 TO LVPS DIGITAL LIGHT 75.8CT01G001...
  • Page 109 Category Coretronic P/N Part Name ACER part NO. Photo CASE/ COVER/ ZOOM BRACK- 70.8ML09GR01 RING 60.JD50H.006 ET AS- MODULE SEMBLY CASE/ COVER/ BRACK- 70.8ML07GR01 60.JD50H.004 COVER ET AS- SEMBLY KEYPAD BOARD 70.8ML01GR01 55.JD50H.003 BLOWER 49.8EF04G001 23.J990H.002 REMOTE REMOTE 45.87U01G107 CONTROL- VZ.J6700.002...

  • Page 110: Serial Number System Definition

    00001 = Serial Numbers 59 = Manufacturing Code 0 = Version Code 1 = Auto-Language Code EX: EYJD501001128000015901 This label represents the serial number for H6500. It is produced at CPC on twenty-eighth week of 2011. Its serial code is 00001. H6500 Confidential...

  • Page 111: Pcba Code Definition

    II. PCBA Code Definition PCBA Code for Projector XXXXXXXXX EEEE Vendor Code Firmware Version MB version Date Code H6500 Confidential...

Table of Contents