Advertisement
Quick Links
PART 1 - GENERAL
1.1
SUMMARY
A. Section includes gas-fired, copper finned-tube pool heaters.
B. Related Sections
Specifier Note: Use as needed
1. Building Services Piping – Division 23 21 00
2. Breeching, Chimneys, and Stacks (Venting) – Division 23 51 00
3. Electrical – Division 23 09 33
1.2
REFERENCES
A. ANSI Z21.10.3/CSA 4.3
B. ASME, Section IV
C. 2006 UMC, Section 1107.6
D. ANSI/ASHRAE 15-1994, Section 8.13.6
E. National Fuel Gas Code
F. NEC
G. ASME CSD-1, 2006
1.3
SUBMITTALS
A. Product data sheet (including dimensions, rated capacities, shipping weights, accessories)
B. Wiring diagram
C. Warranty information
D. Installation and operating instructions
1.4
QUALITY ASSURANCE
A. Regulatory Requirements
1. ANSI Z21.10.3/CSA 4.3
2. Local and national air quality regulations for low NOx (0-30 PPM NOx emissions) pool heaters
B. Certifications
1. CSA
2. ASME HLW Stamp and National Board Listed
3. ISO 9001
1.5
HEAT EXCHANGER WARRANTY
A. Limited ten-year warranty from date of installation
B. Limited twenty-year thermal shock warranty from date of installation
PART 2 - PRODUCTS
2.1
MANUFACTURER
A. Raypak, Inc.
1. Contact: 2151 Eastman Ave., Oxnard, CA 93030; Telephone: (805) 278-5300;
Fax: (800) 872-9725; Web site: www.raypak.com
2. Product: Hi Delta
2.2
POOL HEATERS
A. General
Project Name / Date
®
HI DELTA
, TYPE WHP - MODELS 2072B-2342B
SUGGESTED SPECIFICATIONS
FINNED WATER-TUBE POOL HEATERS
®
copper finned-tube pool heater(s)
Catalog No.:
6000.62
Effective:
9-15-08
Replaces:
6-1-08
1
Advertisement
Related Manuals for Raypak Finned Water-Tube Pool Heaters 2072B-2342B
Summary of Contents for Raypak Finned Water-Tube Pool Heaters 2072B-2342B
- Page 1 B. Limited twenty-year thermal shock warranty from date of installation PART 2 - PRODUCTS MANUFACTURER A. Raypak, Inc. 1. Contact: 2151 Eastman Ave., Oxnard, CA 93030; Telephone: (805) 278-5300; Fax: (800) 872-9725; Web site: www.raypak.com ® 2. Product: Hi Delta POOL HEATERS A. General Project Name / Date ®...
- Page 2 1. The pool heater(s) shall be fired with 2. The pool heater(s) shall be CSA tested and certified with a minimum thermal efficiency of 85 percent at full fire. 3. The pool heater(s) shall be ASME inspected and HLW-stamped and National Board registered for 160 PSIG working pressure, complete with a Manufacturer's Data Report.
- Page 3 associated with constant pump operation. G. Firing Mode 1. For all models, provide on-off firing control of the gas input to the pool heater. H. Pool Heater Diagnostics 1. Provide external LED panel displaying the following pool heater status/faults: a. Power on - Blue b.
- Page 4 L. Pool Heater Pump - Refer to Equipment Schedule M. SureRack™ Pool heater Stacking Kit 1. The pool heaters shall be stacked directly one on top of the other, without offset, to minimize footprint. 2. The stacked pool heaters shall be factory-certified to Seismic Zone 4 requirements. N.
-
Page 5: Installation
6. Manufacturer’s installation instructions, including required service clearances and venting guidelines B. Manufacturer’s representative to verify proper and complete installation. START-UP A. Shall be performed by Raypak factory-trained personnel. B. Test during operation and adjust if necessary: 1. Safeties (2.2 - F) 2. Operating Controls (2.3) 3.