Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Rangemaster Toledo FS Hob
Summary of Contents for Rangemaster Toledo FS Hob
-
Page 1: Users Guide
Users Guide with Installation & Service Instructions U108900 - 02... -
Page 2: U108900
Be safe Warning Accessible parts will become hot in use. To avoid burns and scalds children should be kept away You need clean fresh air - so does your hotplate. Burner flames produce exhaust gases, heat and moisture. Make sure that the kitchen is well ventilated: keep natural ventilation holes open or install a powered hotplate hood that vents outside. -
Page 3: Table Of Contents
Contents Hotplate Burners Warmer The Griddle (optional extra) The Wok cradle (optional extra) Cleaning your hotplate Troubleshooting General Safety Instructions Installation Conversion to LP gas Circuit Diagram Technical Data Page 4 Page 5 Page 6 Page 7 Page 8 Page 10 Page 10 Page 12 Page 17... -
Page 4: Hotplate Burners
The minimum pan diameter recommended is 120mm. NOTE - Griddle plates other than the Rangemaster recommended item, should not be used, or damage to the hob, supports or surround may occur. -
Page 5: Warmer
If a burner flame goes out, turn the control knob off and leave it for one minute before relighting it. You can remove the burner parts for cleaning; see the ‘Cleaning your hotplate’ section of the instructions. You should wipe the top surface of the hotplate around the hotplate burners as soon as possible after spills occur. -
Page 6: The Griddle (Optional Extra)
The Griddle (optional extra) The griddle fits the centre right pan support, front to back. It is designed for cooking food on directly. Don’t use pans of any kind on it. The griddle surface is non-stick and metal cooking utensils (e.g. spatulas) will damage the surface. -
Page 7: The Wok Cradle (Optional Extra)
The Wok cradle (optional extra) The Wok cradle is designed to fit a Typhoon™ Professional 35cm Wok (Part Code 13840S) This is available from leading retailers. If you use a different Wok make sure that it fits the cradle. Woks vary very widely in size and shape. It’s important that the Wok sits down on the pan support - but if the Wok is too small the cradle will not support it properly. -
Page 8: Cleaning Your Hotplate
Cleaning your hotplate Essential information Before thorough cleaning isolate the electricity supply. Remember to switch on the electricity supply before using the hotplate. Never use paint solvents, washing soda, caustic cleaners, biological powders, bleach, chlorine based bleach cleaners, coarse abrasives or salt. Don’t mix different cleaning products - they may react together with hazardous results. -
Page 9: Cleaning Table
electrode notch Now fit the two burner caps, making sure that they are sitting down properly. Cleaning Table Hotplate Part Hotplate Top Pan Supports, Wok Cradle (some models only) Burner Caps Burner Trim Rings (some models only) and Burner Head Griddle Plate (some models only) Outside of Hotplate Part... -
Page 10: Troubleshooting
Troubleshooting What cleaning materials are recommended for the hotplate? See the ‘Cleaning’ section for recommended cleaning materials. We do not recommend Mr. Muscle, as it contains chemicals that may damage the surfaces of your hotplate. If there is an installation problem and I don’t get my original installer to come back to fix it who pays? You do. - Page 11 Clean with caution. If a wet sponge or cloth is used to wipe spills on a hot surface, be careful to avoid steam burns. Some cleansers can produce noxious fumes if applied to a hot surface. Do not use unstable saucepans and position the handles away from the edge of the hotplate.
-
Page 12: Installation
Check the appliance is electrically safe and gas sound when you have finished. Installation Dear Installer Before you start your installation, please complete the details BELOW. If your customer has a problem relating to your installation they will be able to contact you easily. Installer’s Name Installer’s Company Installer’s Telephone number... - Page 13 Check the appliance is electrically safe and gas sound when you have finished. kit. After converting the appliance please attach the Gas Conversion sticker over the appropriate area of the data badge, this will identify the gas type the appliance is now set for.
-
Page 14: Gas Connection
Check the appliance is electrically safe and gas sound when you have finished. We cannot accept responsibility for damage caused by normal use of the hotplate to any material that de- laminates or discolours at temperatures less than 65°C above room temperature. For safety reasons curtains must not be fitted immediately behind the hotplate. -
Page 15: Pressure Testing
Check the appliance is electrically safe and gas sound when you have finished. For LP Gas it should be capable of 50mbar pressure, 70°C temperature rise and carry a red stripe, band or label. WARNINGS: Ensure that the gas supply pipe is never able to touch moveable parts of the built-in cabinet (e.g. -
Page 16: Customer Care
Check the appliance is electrically safe and gas sound when you have finished. If a replacement cable is fitted it must be 250v high temperature rubber/synthetic of 0.75mm conductor size. Connect the replacement cable to the terminal block on the hotplate as shown. Plug connection) For a plug connection a three pin plug to BS1363 with a capacity of not less than 13 ampere must be used and... -
Page 17: Conversion To Lp Gas
WARNING - SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished. Conversion to LP gas Check in the Technical Data section at the back of the book that the hotplate is convertible to the gas you want to use. - Page 18 WARNING - SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished. Stick on label Stick the LP gas label over the natural gas part of the appliance data label.
- Page 19 WARNING - SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished. U108900-02...
-
Page 20: Circuit Diagram
Circuit Diagram Mains Terminal Block Connection shown in circuit diagram is for single phase. Ratings are for 230V 50Hz U108900 - 02 Warmer Switch Warmer Neon Ignition Swirches Code Item Ignition generator Ignition switches Warmer switch Warmer neon Warmer Mains terminal Warmer Element Spark Generator Code Colour... -
Page 21: Technical Data
Technical Data The hotplate is an independent Class 3 built in unit. This hotplate is category II It is supplied set for group H natural gas. A conversion kit from NG to LP gas is packed with the hotplate. INSTALLER: Please leave these instructions with the User. DATA BADGE LOCATION : Base of the hotplate. - Page 22 U108900-02...
- Page 23 U108900-02...
- Page 24 U108900-02 230207...