Siemens SIMOVERT MASTERDRIVES Operating Instructions Manual page 104

Motion control, frequency inverter dc-ac compact plus type
Hide thumbs Also See for SIMOVERT MASTERDRIVES:
Table of Contents

Advertisement

Faults and Alarms
Number / Alarm
Cause
A181
The subprogram number transferred with
block search for level 2 is not the same as the
Prog.no. of block
subprogram number in the NC block.
search forward level 2
<> cmd.
Effect:
NC program execution is inhibited.
A183
The block number for the main program (level
0), which was transferred with block search,
Block no. of block
does not exist in the main program.
search fwd l. 0 does
not exist
Effect:
NC program execution is inhibited.
A184
The block number for the main program (level
0), which was transferred with block search,
Block no. of block
does not contain a subprogram call for
search forward is no
subprogram level 1.
UP call
Effect:
NC program execution is inhibited.
A185
The block number for subprogram level 1,
which was transferred with block search, does
Block no. of block
not exist in the subprogram.
search forward does
not exist
Effect:
NC program execution is inhibited.
A186
The block number for subprogram level 1,
which was transferred with block search, does
Block no of block
not contain a subprogram call for subprogram
search fwd level 1 is no
level 2.
UP call
Effect:
NC program execution is inhibited.
A187
The block number for subprogram level 2,
which was transferred with block search, does
Block no. of block
not exist in the subprogram.
search forward does
not exist
Effect:
NC program execution is inhibited.
A188
The remaining loop count transferred with
block search for subprogram level 1 or 2 is
Remaining no of loops
greater than the programmed loop count.
block search fwd not
allowed
Effect:
NC program execution is inhibited.
A190
The NC block which was read in contains the
"inprocess measurement" or "set actual value
Digital input not
on-the-fly" function, although a digital input
programmed
has not been programmed for this function
(machine data 45).
Effect:
NC program execution is inhibited or aborted,
the axis is brought to a standstill via the
deceleration ramp.
A191
Although the "external block change" function
was programmed, the digital input was not
Digital input not
actuated in order to trigger the external block
actuated
change.
Effect:
The NC program is interrupted, the axis is
brought to a standstill via the deceleration
ramp.
12-26
Counter-measure
For the block search function, the subprogram
number specified in the NC block must be
specified as the subprogram number for level
2.
For the block search function, an existing
block number must be specified as the block
number for the main program.
For the block search function, a block number
with a subprogram call must be specified as
the block number for the main program (level
0) if a block search is to be performed in
subprogram level 1.
For the block search function, a block number
which exists in this subprogram must be
specified as the block number for subprogram
level 1.
For the block search function, a block number
with a subprogram call must be specified as
the block number for subprogram level 1 if a
block search is to be performed in subprogram
level 2.
For the block search function, a block number
which exists in this subprogram must be
specified as the block number for subprogram
level 2.
For the block search function, it is only allowed
to specify a remaining loop count between 0
and the programmed loop count-1.
Program the digital input for the desired
function.
-Correct the program.
-Check the actuation of the digital input.
6SE7087-6KP50
Operating Instructions
SIMOVERT MASTERDRIVES
10.99
Siemens AG

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents