Contents Before You Start Overview and Operation Looking after your Dishwasher Troubleshooting Installation General Information Circuit Diagram Technical Data...
The appliance may tip forward. • The water inside the dishwasher is NOT suitable for drinking. • Do not use solvents of any kind inside your dishwasher. They could cause an explosion. • Open the door very carefully if the dishwasher is operating.
� � � ArtNo.800-0216 - RDW6015 - Control panel Low rinse aid indicator Low salt indicator Delayed start button DocNo.800-0202 - Overview - RDW6015 dishwasher � � � � ½ load button Time remaining indicator ON-OFF indicator light ON-OFF button �...
Page 5
Salt The hardness of water varies from place to place. If hard water is used in the dishwasher, deposits will form on the dishes and utensils. The appliance is equipped with a special softener that uses a salt specifically designed to eliminate lime and minerals from the water.
Fig.2-5 ArtNo.800-0205 - Low rinse aid indicator Fig.2-6 ArtNo.800-207 - Dispenser - Removing the rinse aid cap Fig.2-7 ArtNo.800-208 - Dispenser - Adjusting the rinse aid setting Fig.2-8 ArtNo.800-209 - Dispenser - Detergent compartment � � Fig.2-9 ArtNo.800-210 - Dispenser - Loading the detergent Rinse Aid This product makes dishes sparkle and helps them to dry without spotting.
Directions: Unwrap one tab and place in the detergent dispenser of your dishwasher. No need to add additional salt or rinse aid. The 3-in-1 tab’s salt-action is effective in soft, medium and hard water up to 21dH (around 95% of households).
Page 8
ArtNo.800-0318 - RDW6015 - Fitting the knife rack Arranging Crockery, Glasses, etc. in the Dishwasher Before placing the dishes in the dishwasher, remove larger food particles to prevent the filter from becoming clogged, resulting in reduced performance. If the pots and pans have baked-on food that is extremely hard to remove, we recommend that they are soaked before washed.
Earn savings If only a small number of dishes have been loaded into the dishwasher, selecting a programme that operates at the next lowest temperature will usually be sufficient. Programme data The stated programme data are based on standard operating conditions.
DO NOT open the door fully until the spray arm has stopped rotating. Open the door. When you open the door, the dishwasher will beep ten times every thirty seconds. If the appliance has already heated up or the hot water was...
Page 12
The controls use a microprocessor device to memorize the information about the selected washing program. Once the power is returned to the machine, the dishwasher will resume from the point it was interrupted.
from mains. Overall condition of appliance Check that no grease or scale has accumulated on the inside of the dishwasher. If you discover any deposits: Clean the interior of the dishwasher thoroughly with a detergent solution. Dishwasher salt Check the LOW SALT indicator. Top up with salt, if required (Fig.3-1).
Solvents or Abrasive Cleaning Products To clean the exterior and rubber parts of the dishwasher, do not use solvents or abrasive cleaning products. Rather, use only a cloth and warm soapy water.
filter for the water supply hose is clogged. The drain hose is too low. • If, after these checks the dishwasher still does not function or has any other error displayed, press the programme button and hold it in for about 3 seconds, then press the ON-OFF button to OFF.
Remnants of food are stuck to the dishes, cutlery etc. • Dishwasher was not loaded properly. Jets of water could not reach all parts of the dishes, etc. • Too many items in the rack.
5. Installation Positioning the Dishwasher The dishwasher should be aligned to the front of the adjacent cabinets, with allowance made for the door thickness. The dishwasher has water supply and drain hoses that can be positioned on either to the left or the right.
Care for the external cable • Hold the plug, not the electrical cable, when unplugging the dishwasher. • Make sure that the dishwasher does not trap the electric cable. • Do not step on the cable. • Avoid damage to the electric cable when moving the dishwasher.
Adjust the feet to raise and level the dishwasher to the correct height (Fig.5-6). Using the tool supplied, adjust the rear feet via the studs ‘A’ at the front of the appliance. Adjust the front feet ‘B’...
ArtNo.800-0119 - Adjusting the door springs Fig.5-15 Securing the Dishwasher Using the two screws supplied, secure the dishwasher to the underside of the worktop (Fig.5-12). For non-wooden worktops (e.g. marble) two brackets are provided to allow the appliance to be secured to the sides of the adjacent cabinets.
Measures must be taken to ensure that the units that are subsequently re-sited as freestanding appliances cannot topple over. This can be achieved by bolting the dishwasher to the wall or fitting it under a continuous work surface, that is screwed to the adjacent cupboards.
DATA BADGE LOCATION: Inside face on the side of the door. COUNTRY OF DESTINATION: GB/IE Dimensions ��� ��������� �������������������� ArtNo.800-0127 - 60 dishwasher dimensions Connections Electric Ratings Energy efficiency class on a scale of A (more efficient) to G (less efficient) Standard cycle used...
Page 24
DocNo.000-0001 - Back cover Rangemaster �������������� ����������� ������� ����� w w w.ra n g e m a s t e r.c o .u k ArtNo.000-0003 CE logo...