DVD Player Codes ... 47 Specifications ... 48 Features Your Radio Shack 6-In-One Light and Learn Remote allows you to control your TV, VCR, cable/SAT/DSS converter, DVD player, CD player, and an auxiliary de- vice with one easy-to-use remote control.
A Quick Look at the Keys Your Radio Shack 6-In-One Remote controls the most-used functions on your TV, VCR, cable/SAT/ DSS converter, DVD player, CD player, and auxiliary device.
Page 5
The following table lists all keys and how they func- tion. Function Use to program the remote control. Use to turn the backlight on or off. When on, any key press activates the back- light. It stays on for up to 5 seconds after the last key press.
Page 6
Function THEATER Use to access function keys without changing device remotes (See “Using Home Theater” on Page 20). The following tables explain how selected keys func- tion in different modes. For example, Channel-Up key in TV, VCR, and CBL/SAT modes. However, in DVD mode, acts as a Skip Forward key.
GUIDE Setup Menu Guide MENU DVD Menu Program INFO Display Display Skip Forward Preset + CH– Skip Reverse Preset – LAST Return Random TV/VCR TV/DVD Input Rewind Rewind PLAY Play Play Fast Forward Fast Forward Record Record STOP Stop Stop PAUSE Pause Pause...
Page 8
Cautions: • Use only fresh batteries of the required size and recommended type. • Do not use rechargeable batteries. • Do not mix old and new batteries or different types of batteries (standard or alkaline). • Always remove old or weak batteries. Batteries can leak chemicals that can destroy electronic parts.
DEVICE TYPES You can use the remote control’s device keys to con- trol the following types of devices: — TV — VCR or PVR (Personal Video Recorder) — Cable converter or SAT/DSS receiver CBL/SAT — DVD or LD Player — Amplifier, tuner or other audio device –...
4. Hold down until the remote’s red light blinks twice, then enter the first 4-digit manufacturer’s code for the desired device. When the red light blinks twice, the remote control has accepted the code. For example, to set up the remote control of a Panasonic TV (manufacturer’s code 0051), press , hold down until the red light blinks twice,...
4. Enter the two-, three- or four-digit number for your favorite channel. 5. If you entered a two- or three-digit channel num- ber , you must do one of the following: if your orig- inal remote requires you to press Enter or Select to send a command, then do so after entering the digits of your favorite channel.
PROGRAMMING MACROS Your remote has four macro keys ( , and ) that store up to three channels SPORTS NEWS per macro key for instant tuning of TV or cable/satellite channels. For example, if your favorite sports channel on your cable service is 061, you can store it as an in- stant tune-in macro.
Follow these steps to program the power key. 1. Turn off all devices. 2. Hold down until the red light blinks twice. 3. Press . The red light blinks twice. 9 9 5 4. Press POWER 5. Press the device keys ) in the desired order.
Note: Other reassignments are possible, including adding a second TV or second DVD player to an un- used device key. Simply repeat Step 3 with your de- sired choices. Resetting Reassigned Device Keys If you have reassigned a key (for example, you reas- signed the DVD key to operate a second VCR), and want to return to the default setting (for the example, DVD mode), follow these steps.
5. Place the device’s remote control head-to-head (about 2 inches apart) with the 6-In-One Remote. 6. On the device’s remote control, hold down the key to be learned until the red light on the 6-In-One Remote blinks twice. If the red light does not blink twice, repeat Steps 1–...
USING THE REMOTE Once you have completed all the programming for the remote (see “Preparation” on Page 7), you are ready to use your 6-In-One Remote. 1. Point the remote at the desired device and press the device key ( CBL/SAT ).
Note: For on-air broadcast scans, press , then press to start the scan. SCAN/FAV USING FAVORITE CHANNEL SCAN To scan favorite channels, you must first program the favorite channel table (see “Programming Favorite Channel Scan” on Page 10). Press the desired device key ( ), then CBL/SAT press...
CD, or AUX) upon its selection, then perform the steps listed in the appropriate section below. Volume Unlock on a Cable Convertor or SAT/DSS Receiver 1. Press CBL/SAT 2. Hold down until the red light blinks twice. 3. Press . The red light blinks twice. 9 9 3 4.
2. Hold down until the red light blinks twice. 3. Press . The red light blinks twice. 9 9 3 4. Press . The red light blinks four times. VOL– To control the volume through your auxiliary device, press before using the volume controls. Volume Unlock on an Auxiliary Device 1.
Note: If your device has a built-in sleep function, pressing activates the device’s sleep SLEEP timer. 3. Press again within 10 seconds to add SLEEP another 15 minutes. Repeat as desired up to a maximum of 60 minutes. 4. Place the 6-In-One Remote directly in front of the device you chose to enter sleep mode.
Note: Once a Function Group is assigned to a device, the device can use all keys in the designated Function Group. Function Groups Function Group 1 — Transport Keys (Play, Stop, Fast Forward, Rewind, Pause) Function Group 2 — Volume Keys (Volume Up, Vol- ume Down, and Mute) Function Group 3 —...
1. On the remote, press THEATER 2. Hold down until the red light blinks twice. 3. Enter . The red light blinks twice. 9 7 9 4. Press the desired device key from Device Group ). Press Function Group 1 (the transport keys). The red light blinks twice.
3. To exit Home Theater mode, press the device key of the desired mode. USING MANUAL CODE SEARCH If your home entertainment device does not respond to remote control commands after trying all of the codes listed for your brand, or if your brand is not list- ed, try searching for your code.
1. On the remote control, press the desired device key once. 2. Hold down until the red light blinks twice. 3. Press . The red light blinks twice. 9 9 0 4. To view the code for the first digit, press the number of blinks (for example, if there are three blinks, the first digit is 3) and write down the number.
and wipe it with a damp cloth occasionally to keep it looking new. Modifying or tampering with the remote’s internal com- ponents can cause a malfunction and might invalidate its warranty. If your remote is not performing as it should, take it to your local RadioShack store for as- sistance.
Specifications Power ...(4) AAA Batteries Dimensions (HWD) ... 9.3 in (235 mm Weight (Without Batteries) ... 5.5 oz Specifications are typical; individual units might vary. Specifica- tions are subject to change and improvement without notice. Limited Ninety-Day Warranty This product is warranted by RadioShack against manufacturing defects in ma- terial and workmanship under normal use for ninety (90) days from the date of purchase from RadioShack company-owned stores and authorized RadioShack franchisees and dealers.
Need help?
Do you have a question about the Light and Learn Remote and is the answer not in the manual?
Questions and answers