Page 3
This guarantee does not affect your statutory rights.This guarantee is only valid in the UK. For further technical advice, spare parts or repair service (outside of guarantee) please contact the customer helpline number on 0845 607 6380. 18V RECIPROCATING SAW SF2842 SF2842 CSR18P-M-060425.indd 3 2006-5-25 11:18:26...
Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. f. Dress properly. Do not wear loose clothing or jewellery. Keep SF2842 CSR18P-M-060425.indd 4 2006-5-25 11:18:27...
Page 5
Shorting the battery terminal together may cause burns or a fire. e. Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid 18V RECIPROCATING SAW SF2842 SF2842 CSR18P-M-060425.indd 5 2006-5-25 11:18:27...
19. When an extension cable is required you must ensure it has the correct ampere rating for your power tool and is in a safe electrical condition. 20. Ensure your mains supply voltage is same as indicated on the rating plate. SF2842 CSR18P-M-060425.indd 6 2006-5-25 11:18:27...
Page 7
In case of contact with the eyes rinse, rinse thoroughly with clean water and seek medical treatment immediately. SYMBOLS Read the manual Warning Wear gloves Wear dust mask,eye & ear protection Conforms to relevant safety standards 18V RECIPROCATING SAW SF2842 SF2842 CSR18P-M-060425.indd 7 2006-5-25 11:18:27...
Page 8
ON/OFF SWITCH LOCK OFF SWITCH HAND GRIP AREAS TOOL-FREE BLADE CLAMP LEVER PIVOTING FOOT PLATE BATTERY PACK RELEASE LATCH BATTERY PACK CHARGER CHARGED INDICATOR LIGHT (GREEN) 10. CHARGING INDICATOR LIGHT (RED) SF2842 CSR18P-M-060425.indd 8 2006-5-25 11:18:30...
12mm Max cutting depth in tube: 76mm Stroke: 22mm Normal charging time: 1 hour Battery capacity: 1.5Ah Machine weight 2.86kg ACCESSORIES 1hr charger 1.5Ah Ni-cd battery pack Saw blade for wood 18V RECIPROCATING SAW SF2842 SF2842 CSR18P-M-060425.indd 9 2006-5-25 11:18:30...
Page 10
Warning: After long usage the battery will become hot, let the hot battery cool down for 1 hour before recharging. SF2842 CSR18P-M-060425.indd 10 2006-5-25 11:18:30...
Page 11
The pivoting blade foot must be held firmly against the material being cut to reduce saw vibration, blade jumping and blade breakage. To adjust, hold saw firmly and pivot foot plate to desired position. (See fig6) Fig 6 18V RECIPROCATING SAW SF2842 SF2842 CSR18P-M-060425.indd 11 2006-5-25 11:18:31...
Page 12
(see fig10 & fig11). Use a slow speed to start the cut to avoid breaking the blade Fig 10 but increase to correct speed once the cut has SF2842 CSR18P-M-060425.indd 12 2006-5-25 11:18:33...
If the battery is not fully charged, recharge the battery with the supplied battery charger. Note: Do not charge the battery with a different charger. Charge battery pack only with the charger provided. 18V RECIPROCATING SAW SF2842 SF2842 CSR18P-M-060425.indd 13 2006-5-25 11:18:33...
35 C as this will affect performance. ENVIRONMENTAL PROTECTION Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice. SF2842 CSR18P-M-060425.indd 14 2006-5-25 11:18:34...
Page 15
L. A 13AMP (BS1363 or BS1363/A) plug must be used and a 3 AMP fuse must be fitted. 3 AMP FUSE BLUE N (NEUTRAL) BROWN L (LIVE) OUTER CABLE GRIP SLEEVE 18V RECIPROCATING SAW SF2842 SF2842 CSR18P-M-060425.indd 15 2006-5-25 11:18:34...