Iec 61850 Goose Integers - GE L60 Instruction Manual

5 SETTINGS
GOOSE Analogs that represent current, voltage, power, frequency, angles, or power factor can be used in a FlexEle-
ment. The following text must be used in the UNITS setting, to represent these types of analogs: A, V, W, var, VA, Hz,
deg, and no text (blank setting) for power factor.
GOOSE Analogs can be compared to other GOOSE Analogs with any character string or no string.
• GOOSE ANALOG 1 PU: This setting specifies the per-unit base factor when using the GOOSE analog input FlexAna-
log values in other L60 features, such as FlexElements. The base factor is applied to the GOOSE analog input FlexAn-
alog quantity to normalize it to a per-unit quantity. The base units are described in the following table.
The per-unit base setting represents thousands, not single units. For example, a PU base of 1.000 is actually 1000 and
a PU base of 0.001 is 1.
When using GOOSE Analogs and PU base in FlexElements, the largest value that can be displayed in the FlexEle-
ment actual values is 2,140,000.000.
Table 5–35: GOOSE ANALOG INPUT BASE UNITS
ELEMENT
BREAKER ARCING AMPS
(Brk X Arc Amp A, B, and C)
DCmA
FREQUENCY
PHASE ANGLE
POWER FACTOR
RTDs
SOURCE CURRENT
SOURCE POWER
SOURCE VOLTAGE
SYNCHROCHECK
(Max Delta Volts)
The GOOSE analog input FlexAnalog values are available for use in other L60 functions that use FlexAnalog values.

PATH: SETTINGS INPUTS/OUTPUTS
 GOOSE UINTEGER
 INPUT 1
MESSAGE
The IEC 61850 GOOSE uinteger inputs feature allows the transmission of FlexInteger values between any two UR-series
devices. The following settings are available for each GOOSE uinteger input.
• UINTEGER 1 DEFAULT: This setting specifies the value of the GOOSE uinteger input when the sending device is
offline and the
UINTEGER 1 DEFAULT MODE
number.
• UINTEGER 1 DEFAULT MODE: When the sending device is offline and this setting is "Last Known", the value of the
GOOSE uinteger input remains at the last received value. When the sending device is offline and this setting value is
"Default Value", then the value of the GOOSE uinteger input is defined by the
The GOOSE integer input FlexInteger values are available for use in other L60 functions that use FlexInteger values.
GE Multilin
BASE UNITS
2
BASE = 2000 kA × cycle
BASE = maximum value of the DCMA INPUT MAX
under the +IN and –IN inputs.
f = 1 Hz
BASE
ϕ
= 360 degrees (see the UR angle referencing convention)
BASE
PF = 1.00
BASE
BASE = 100°C
I = maximum nominal primary RMS value of the +IN and –IN inputs
BASE
P = maximum value of V
BASE BASE
V = maximum nominal primary RMS value of the +IN and –IN inputs
BASE
V = maximum primary RMS value of all the sources related to the +IN and –IN inputs
BASE

IEC 61850 GOOSE UINTEGERS
UINTEGER 1 DEFAULT:
1000
UINTEGER 1 DEFAULT
MODE: Default Value
is set to "Default Value".This setting is stored as a 32-bit unsigned integer
L60 Line Phase Comparison System
setting for the two transducers configured
× I for the +IN and –IN inputs
BASE

5.7.13 IEC 61850 GOOSE INTEGERS


GOOSE UINTEGER INPUT 1(16)
Range: 0 to 429496295 in steps of 1
Range: Default Value, Last Known
UINTEGER 1 DEFAULT
5.7 INPUTS/OUTPUTS
setting.
5-309
5