Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Spectra PowerBox 100-IoT-J19
Summary of Contents for Spectra PowerBox 100-IoT-J19
- Page 1 SPECTRA POWERBOX 100-IoT USER MANUAL Version 1.1 – November 2017...
-
Page 2: Table Of Contents
1.1.3 Photo of Rear Panel …..……………………………………..14 1.2 Hardware Specification …..…………………………………………… 15 1.3 System I/O ……………………………………………………………… 16 1.3.1 Spectra PowerBox 100-IoT……………………………….…… 16 1.3.2 Spectra PowerBox 100-IoT with modules..……………….…… 18 1.4 Mechanical Dimension …..……………………………………………. 19 Chapter 2 Jumpers and Connectors 2.1 Jumper Setting ………………………………………………………..21 2.2 Location of the Switches and Connectors……..…………………….. - Page 3 4.7.1 Save Changes and Reset………………………………………. 64 4.7.2 Discard Changes and Reset……………………………………. 64 4.7.3 Restore Defaults …………………………………………………. 64 4.7.4 Save as User Defaults ……………………………………………64 4.7.5 Restore User Defaults ………………………..…………………. 64 Spectra GmbH & Co. KG User Manual Version 1.1 vertrieb@spectra.de Spectra PowerBox 100-IoT...
- Page 4 8.2.2 Restarting the Node-Red Process .…...…..….…………….. 8.2.3 Stopping the Node-Red Process .…...…..….…………….. 8.2.4 Starting the Node-Red Process ……..……..….…………….. 8.3 Activities for Repairing Node-Red Instances Not Starting ……….. Spectra GmbH & Co. KG User Manual Version 1.1 vertrieb@spectra.de Spectra PowerBox 100-IoT...
-
Page 5: Revision
2017/11/09 Copyright Notice © 2017 by Spectra GmbH & Co. KG. All rights are reserved. No parts of this manual may be copied, modified, or reproduced in any form or by any means for commercial use without the prior written permission of Spectra GmbH &... -
Page 6: Product Warranty Statement
(such as a fuse, battery, etc.), are not warranted. Before sending your product in, you will need to fill in a Spectra RMA Request Form and obtain a RMA number from us. Please go to www.spectra.de/RMA... -
Page 7: Technical Support And Assistance
This indication alerts operators to an operation that, if not strictly observed, may result in safety hazards to personnel or damage to equipment. This indication provides additional information to complete a task easily. Spectra GmbH & Co. KG User Manual Version 1.1 vertrieb@spectra.de... -
Page 8: Safety Precaution
The equipment has obvious signs of breakage. 14. CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Spectra GmbH & Co. KG User Manual Version 1.1 vertrieb@spectra.de... -
Page 9: Package Content
Before installation, please ensure all the items listed in the following table are included in the package. Item Description Q’ty Spectra PowerBox 100-IoT Embedded System Spectra Linux OS Recovery stick * Power Terminal Block Connector (Male) Screw Pack (for HDD / Mini-PCIe / Wall & VESA Mounting) Wall Mount Kit DVI-I to VGA Adapter Remote Power On/Off Terminal Block Connector (Male) Note: Notify your sales representative if any of the above items are missing or damaged. -
Page 10: Ordering Information
Edge-PC, Intel® Celeron® J1900 Processor, Spectra PowerBox 100-IoT-J19 Spectra Linux OS 64-bit Edge-PC, Intel® Atom™ Quad Core E3845 Processor, Spectra PowerBox 100-IoT-QC Spectra Linux OS 64-bit Spectra GmbH & Co. KG User Manual Version 1.1 vertrieb@spectra.de Spectra PowerBox 100-IoT November 2017... -
Page 11: Optional Accessory
COM-Module for PowerBox 100, 1x Display Port, incl. Bracket PB-100-DVI-Modul COM-Module for PowerBox 100, 1x DVI-D, incl. Bracket PB-100-VGA-Modul COM-Module for PowerBox 100, 1x VGA, incl. Bracket Spectra GmbH & Co. KG User Manual Version 1.1 vertrieb@spectra.de Spectra PowerBox 100-IoT... -
Page 12: Chapter 1 Product Introductions
Chapter 1 PRODUCT INTRODUCTIONS... -
Page 13: Overview
J1900 (2.0GHz) platform; it has integrated HD graphics processor. This can bring economic advantages on budget and also fulfill the needs for industrial computing tasks. The Spectra PowerBox 100 manages to pack a diverse array of I/O into its small form factor, with one DVI-I port, two RS-232/422/485 COM ports, dual Gb LAN ports, four USB ports and one set of Mic-in and Line-out. -
Page 14: Photo Of Rear Panel
Spectra PowerBox 100 Spectra PowerBox 100 Spectra PowerBox 100 w/ PB-100-DVI Module w/ PB-100-COM Module Spectra PowerBox 100 Spectra PowerBox 100 w/ PB-100-DP Module w/ PB-100-VGA Module Spectra GmbH & Co. KG User Manual Version 1.1 vertrieb@spectra.de Spectra PowerBox 100-IoT November 2017... -
Page 15: Hardware Specification
• FCC Class A • 1x Remote Power On/Off Connector (2-pin Terminal Block) Operating System • 1x Universal I/O Bracket • Spectra Linux OS, 64-bit • 2x Antenna Holes Power Requirement • Support AT/ATX Power Mode • Power Input Voltage 9~48VDC •... -
Page 16: System I/O
Used to connect a microphone Remote Power Terminal Block Line-out Used to plug a remote power on/off switch with Used to connect a speaker terminal block Spectra GmbH & Co. KG User Manual Version 1.1 vertrieb@spectra.de Spectra PowerBox 100-IoT November 2017... - Page 17 COM / DisplayPort / DVI / VGA. Do not change the module by yourself, it may cause damage to your Spectra PowerBox 100. Please contact with your regional dealer for more information about it. Spectra GmbH & Co. KG User Manual Version 1.1...
-
Page 18: Spectra Powerbox 100-Iot With Modules
Chapter 1: Product Introductions 1.3.2 Spectra PowerBox 100 Series w/ modules w/ PB-100-COM Front Rear w/ PB-100-DP w/ PB-100-DVI Front Rear w/ PB-100-VGA Front Rear Spectra GmbH & Co. KG User Manual Version 1.1 vertrieb@spectra.de Spectra PowerBox 100-IoT November 2017... -
Page 19: Mechanical Dimension
Chapter 1: Product Introductions 1.4 Mechanical Dimensions Each of the Spectra PowerBox computers has the same mechanical dimension Spectra GmbH & Co. KG User Manual Version 1.1 vertrieb@spectra.de Spectra PowerBox 100-IoT November 2017... -
Page 20: Chapter 2 Jumpers And Connectors
Chapter 2 JUMPERS AND CONNECTORS... -
Page 21: Jumper Setting
Chapter 2: Jumpers and Connectors 2.1 Jumpers Settings The Spectra PowerBox 100 is featured with jumper-free design 2.2 Location of the Jumpers and Connectors 2.2.1 Top View Spectra GmbH & Co. KG User Manual Version 1.1 vertrieb@spectra.de Spectra PowerBox 100-IoT... -
Page 22: Bottom View
Chapter 2: Jumpers and Connectors 2.2.2 Bottom View Spectra GmbH & Co. KG User Manual Version 1.1 vertrieb@spectra.de Spectra PowerBox 100-IoT November 2017... -
Page 23: List Of Switches And Connectors
MINIPCIE1 Mini PCI-Express Socket PWR_SW2 External Power Connector SATA1 SATA with Power Connector USB2_1 / USB2_2 / USB2_3 USB 2.0 Connector USB3_1 USB 3.0 Connector Spectra GmbH & Co. KG User Manual Version 1.1 vertrieb@spectra.de Spectra PowerBox 100-IoT November 2017... -
Page 24: Switches Definitions
Switch Definition Right ATX Power Mode（Default） Left AT Power Mode CLR_CMOS1：Clear CMOS Switch Switch Definition Clear CMOS Normal Status (Default) PWR_SW1：Power Switch Definition Power Button Spectra GmbH & Co. KG User Manual Version 1.1 vertrieb@spectra.de Spectra PowerBox 100-IoT November 2017... -
Page 25: Connectors Definitions
Definition Definition WAKE# +3.3V +1.5V SMB_CLK MINIPCIE_TXN3/SATA_TXN1 +1.5V SMB_DATA CLKREQ# MINIPCIE_TXP3/SATA_TXP1 USB_6N MINIPCIE_CLKN3 USB_6P MINIPCIE_CLKP3 +3.3V +3.3V +3.3V MINIPCIE RST# +1.5V MINIPCIE_RXN3/SATA_RXP1 +3.3V MINIPCIE_RXP3/SATA_RXN1 +3.3V Spectra GmbH & Co. KG User Manual Version 1.1 vertrieb@spectra.de Spectra PowerBox 100-IoT November 2017... -
Page 26: Minipcie1：Mini Pci-Express Socket
Definition Definition WAKE# +3.3V +1.5V SMB_CLK MINIPCIE_TXN4 +1.5V SMB_DATA CLKREQ# MINIPCIE_TXP4 USB_7N MINIPCIE_CLKN4 USB_7P MINIPCIE_CLKP4 +3.3V +3.3V +3.3V MINIPCIE RST# +1.5V MINIPCIE_RXN4 +3.3V MINIPCIE_RXP4 +3.3V Spectra GmbH & Co. KG User Manual Version 1.1 vertrieb@spectra.de Spectra PowerBox 100-IoT November 2017... -
Page 27: Dc_In1：Dc Power Input Connector (9~48V)
2.5.4 PWR_SW2：External remote power on/off switch (Note: Please do not apply power to the pins. This port is used to apply a switch.) 1 2 Definition PWR_ON Spectra GmbH & Co. KG User Manual Version 1.1 vertrieb@spectra.de Spectra PowerBox 100-IoT November 2017... -
Page 28: Com1_1：Rs232 / Rs422 / Rs485 Connector
RX2- GND2 DSR2 RTS2 CTS2 NOTE： (For Spectra PowerBox w/ PB-100-COM Modul only) The optional module 2 COM ports <RS232 / RS422 / RS485> are with +5/ +12VDC for RI pin (Pin 9). Spectra GmbH & Co. KG User Manual Version 1.1... -
Page 29: Com3 & Com4：Voltage Select
2.5.8 DVI_I1：DVI-I Connector Definition Definition DVI_TX2- DVI Hot Plug Detect DVI_TX2+ DVI_TX0- DVI_TX0+ DDC_CLOCK DDC_DATA VGA VSYNC DVI_TXCLK+ DVI_TX1- DVI_TXCLK- DVI_TX1+ VGA_RED VGA_GREEN VGA_BLUE VGA_HSYNC Spectra GmbH & Co. KG User Manual Version 1.1 vertrieb@spectra.de Spectra PowerBox 100-IoT November 2017... -
Page 30: Lan1：Rj45 With Led Connector
10Mbps Network Link 2.5.11 LED1：Power / HDD Access LED Status Definition HDD LED+ HDD LED- POWER LED+ POWER LED- LED Status LED Color Yellow POWER Green Spectra GmbH & Co. KG User Manual Version 1.1 vertrieb@spectra.de Spectra PowerBox 100-IoT November 2017... -
Page 31: Line_Out1: Line-Out Jack (Green)
Connector Type：5-pin Phone Jack Connector Type：5-pin Phone Jack Definition Definition OUT_R MIC_R OUT_L MIC_L 2.5.14 SATA1：SATA Connector Definition Definition +3.3V +3.3V +12V +3.3V +12V +12V Spectra GmbH & Co. KG User Manual Version 1.1 vertrieb@spectra.de Spectra PowerBox 100-IoT November 2017... -
Page 32: Usb1 & Usb2 & Usb3：Usb2.0 Connector, Type A
2.5.15 USB1 & USB2 & USB3：USB2.0 Connector, Type A USB1 USB2 USB3 Definition Definition Definition USB_DATA3- USB_DATA2- USB_DATA1- USB_DATA3+ USB_DATA2+ USB_DATA1+ 2.5.16 USB4：USB3.0 Connector, Type A USB4 Definition USB_DATA0- USB_DATA0+ Spectra GmbH & Co. KG User Manual Version 1.1 vertrieb@spectra.de Spectra PowerBox 100-IoT November 2017... -
Page 33: Chapter 3 Mounting
Chapter 3 MOUNTING... -
Page 34: Wall Mount Brackets
Chapter 3: System Setup 3.1 Wall Mount Brackets The Spectra PowerBox 100 offers Wall Mount that customers can install system on the wall in convenient and economical way. 1. The mounting holes are at the bottom of system. Use provided 4 screws to fasten the bracket with each side of system together. -
Page 35: Side Mount Bracket
Chapter 3: System Setup 3.2 Side Mount Bracket The Spectra PowerBox 100 offers Side Mount that customer can install system to the right or left side of wall to create effective of space. 1. The mounting holes are at the bottom of system. Fasten the 4 screws to fix the side mount bracket with system together. -
Page 36: Vesa Mount Bracket
Chapter 3: System Setup 3.3 VESA Mount Brackets The Spectra PowerBox 100 offers VESA Mount that customer can mount system with panel complying with VESA 75mm and 100 mm standard for various usage. 2. Provided below is mounted with VESA 1. -
Page 37: Din-Rail Mount Bracket
Chapter 3: System Setup 3.4 DIN-Rail Mount Bracket The Spectra PowerBox 100 offers DIN-Rail Mount that customer can install system on the DIN Rail. 1. The mounting holes are at the bottom of system. Fasten the 2 screws to fix the DIN- Rail mount bracket with system together. -
Page 38: Chapter 4 Bios Setup
Chapter 4 BIOS SETUP... -
Page 39: Bios Introduction
Then you can use the control keys to enter values and move from field to field within a sub-menu. If you want to return to the main menu, just press the <Esc>. Spectra GmbH & Co. KG User Manual Version 1.1 vertrieb@spectra.de... -
Page 40: Main Setup
4.2.1 System Date Set the date. Please use <Tab> to switch between date elements. 4.2.2 System Time Set the time. Please use <Tab> to switch between time elements. Spectra GmbH & Co. KG User Manual Version 1.1 vertrieb@spectra.de Spectra PowerBox 100-IoT... -
Page 41: Advanced Setup
You can select any of the items in the left frame of the screen to go to the sub menus. 4.3.1 ACPI Settings ■ Enable ACPI Auto Configuration This enables ACPI power management of the system. Spectra GmbH & Co. KG User Manual Version 1.1 vertrieb@spectra.de... -
Page 42: Super I/O Configuration
■ Serial Port 4 Configuration This allows you to configure serial port 4. We’ll use serial port 1 configuration as an example in the manual. Similar settings apply to other serial ports configuration. Spectra GmbH & Co. KG User Manual Version 1.1 vertrieb@spectra.de... - Page 43 Entering serial port 1 configuration allows you to enable or disable the port ,and also to configure settings and mode of operations. To avoid conflicted setting with other serial ports, default setting is recommended. Spectra GmbH & Co. KG User Manual Version 1.1 vertrieb@spectra.de...
- Page 44 Chapter 4: BIOS Setup Entering parallel port configuration allows you to enable or disable the port ,and also to configure settings and mode of device operation. Default setting is recommended. Spectra GmbH & Co. KG User Manual Version 1.1 vertrieb@spectra.de...
-
Page 45: Hardware Monitor
Chapter 4: BIOS Setup 4.3.3 Hardware Monitor This allows you to monitor system’s CPU temperature and voltages. Spectra GmbH & Co. KG User Manual Version 1.1 vertrieb@spectra.de Spectra PowerBox 100-IoT November 2017... -
Page 46: Serial Port Console Redirection
Chapter 4: BIOS Setup 4.3.4 Serial Port Console Redirection This allows you to enable and disable serial (COM) port(s) for console use. Default setting is disabled. Spectra GmbH & Co. KG User Manual Version 1.1 vertrieb@spectra.de Spectra PowerBox 100-IoT November 2017... -
Page 47: Cpu Configuration
Use of default setting is recommended in the section. ■ Limit CPUID Maximum Default is Disabled. ■ Execute Disable Bit Default is Enabled. ■ Intel Virtualization Technology Default is Enabled. Spectra GmbH & Co. KG User Manual Version 1.1 vertrieb@spectra.de Spectra PowerBox 100-IoT November 2017... - Page 48 Chapter 4: BIOS Setup Entering Socket 0 CPU Information shows CPU hardware details and supported features. Spectra GmbH & Co. KG User Manual Version 1.1 vertrieb@spectra.de Spectra PowerBox 100-IoT November 2017...
-
Page 49: Thermal Configuration
This allows you to configure temperature of ACPI of OS to trip or shut down the system, or to begin throttling CPU. Use of default setting is recommended in the section. Spectra GmbH & Co. KG User Manual Version 1.1 vertrieb@spectra.de... - Page 50 This allows 90C (default), 87C, 85C, 79C, &1C, 63C, 55C, 47C, 39C, 31C, 23C, 15C. ■ Passive Trip Point This allows 90C, 87C, 85C (default), 79C, &1C, 63C, 55C, 47C, 39C, 31C, 23C, 15C. ■ DTS Default is Disabled. Spectra GmbH & Co. KG User Manual Version 1.1 vertrieb@spectra.de Spectra PowerBox 100-IoT...
-
Page 51: Sata Configuration
■ SATA Mode This allows to set AHCI mode (default) or IDE mode. ■ Serial-ATA Port 0 Default is Enabled. ■ Serial-ATA Port 1 Default is Enabled. Spectra GmbH & Co. KG User Manual Version 1.1 vertrieb@spectra.de Spectra PowerBox 100-IoT November 2017... -
Page 52: Os Selection
Chapter 4: BIOS Setup 4.3.8 OS Selection For the Spectra Linux OS to operate properly, this option has to be ste to “all other OS”. Spectra GmbH & Co. KG User Manual Version 1.1 vertrieb@spectra.de Spectra PowerBox 100-IoT November 2017... -
Page 53: Csm Configuration
Chapter 4: BIOS Setup 4.3.9 CSM (Compatibility Support Module) Configuration Following shows default settings. Spectra GmbH & Co. KG User Manual Version 1.1 vertrieb@spectra.de Spectra PowerBox 100-IoT November 2017... - Page 54 Allows user to select whether to enable the UEFI or legacy option ROM for the storage device controller. Do not launch: Disables option ROM. UEFI: Enables UEFI option ROM only. Legacy: Enables legacy option ROM only. Spectra GmbH & Co. KG User Manual Version 1.1 vertrieb@spectra.de Spectra PowerBox 100-IoT...
-
Page 55: Usb Configuration
Chapter 4: BIOS Setup 4.3.10 USB Configuration Following shows default settings. Spectra GmbH & Co. KG User Manual Version 1.1 vertrieb@spectra.de Spectra PowerBox 100-IoT November 2017... - Page 56 Determines whether to enable EHCI Hand-off feature for an operating system without EHCI Hand-off support. ■ USB Mass Storage Driver Support Enables or disables support for USB storage devices. Spectra GmbH & Co. KG User Manual Version 1.1 vertrieb@spectra.de Spectra PowerBox 100-IoT...
-
Page 57: Chipset
You can select any of the items in the left frame of the screen to go to the sub menus. 4.4.1 North Bridge This section provides information on the installed memory size and memory/onboard graphics-related configuration options. Spectra GmbH & Co. KG User Manual Version 1.1 vertrieb@spectra.de Spectra PowerBox 100-IoT... - Page 58 This item will allow users to enable or disable DOP CG. GTT Size GTT size optimal between 1MB or 2MB. IGD Thermal This item will allow users to enable or disable IGD Thermal. Spectra GmbH & Co. KG User Manual Version 1.1 vertrieb@spectra.de Spectra PowerBox 100-IoT...
-
Page 59: South Bridge
Chapter 4: BIOS Setup 4.4.2 South Bridge Following shows default settings. Spectra GmbH & Co. KG User Manual Version 1.1 vertrieb@spectra.de Spectra PowerBox 100-IoT November 2017... -
Page 60: Audio Controller
USB Port 2 This item will allow users to enable or disable USB Port 2. USB Port 3 This item will allow users to enable or disable USB Port 3. Spectra GmbH & Co. KG User Manual Version 1.1 vertrieb@spectra.de... - Page 61 PCI Express Port 3 This item will allow users to enable or disable PCI Express Port 3. Speed Change the PCI Express interface speed. Select <AUTO> ,<Gen 2> or <Gen 1> Spectra GmbH & Co. KG User Manual Version 1.1 vertrieb@spectra.de...
-
Page 62: Security
4.5.1 Administrator Password Administrator Password controls access to the BIOS Setup utility. 4.5.2 User Password User Password controls access to the system at boot and to the BIOS Setup utility. Spectra GmbH & Co. KG User Manual Version 1.1 vertrieb@spectra.de... -
Page 63: Boot
4.6.4 Fast Boot This item allows user to enable or disable Fast Boot option. 4.6.5 UEFI Boot This allows to boot device with UEFI-based (not legacy) OS. Spectra GmbH & Co. KG User Manual Version 1.1 vertrieb@spectra.de Spectra PowerBox 100-IoT... -
Page 64: Save & Exit
This item allows user to save the changes done so far as user defaults. 4.7.5 Restore User Defaults This item allows user to restore the user defaults to all the options. Spectra GmbH & Co. KG User Manual Version 1.1 vertrieb@spectra.de... -
Page 65: Chapter 5 Iiot Configuration
CHAPTER 5 IIoT CONFIGURATION... -
Page 66: Pb100-Iot Mouse/Keyboard Commissioning
5.1 PB100 IoT Mouse / Keyboard Commissioning The Spectra PowerBox 100-IoT is switched on by pressing the power button at the front of the housing. Input devices such as mouse and keyboard are connected via the USB ports which are also located at the front side. -
Page 67: Password Reset
During our regular office hours (Monday to Friday from 8 am to 5 pm), the Spectra support will generate a reset key which must be entered in the field “Please enter your reset key below”. -
Page 68: Changing The Password Of The Web Interface User
To prevent unauthorised persons from accessing the Web interface, the password of the Web interface user should be changed immediately after having commissioned the Spectra PowerBox 100-IoT! 5.2.4 Changing the Password of the Web Interface User Click on the avatar ( ) in the top right section to access your password change. -
Page 69: Configuration Options
5.3.2 Changing the Computer Name of the Spectra PowerBox 100-IoT At the HOSTNAME menu item, the computer name of the Spectra PowerBox 100-IoT can be changed. To ensure that all services are correctly functioning, the Spectra PowerBox 100-IoT must be restarted after having successfully changed the computer name! 5.3.3 Creating User Accounts for Node-Red / Allowing Anonymous Use... -
Page 70: Network Configuration
At the “NETWORK CONFIGURATION” menu item, the network can be configurated. The Web interface only allows for the configuration of the Ethernet network interfaces integrated in the Spectra PowerBox 100-IoT. Any optionally available WiFi hardware is configured via the XFCE operating system interface. - Page 71 5.3.4.1 General Settings The “Offline Mode” option enables the user to switch off the complete network system of the Spectra PowerBox 100-IoT (including optionally available WiFi components) and to set it to “Flight Mode”. If you only want to disable the integrated Ethernet network interfaces, you just have to remove the checkmark from the “Wired Networking enabled”...
- Page 72 5.3.4.2 Wired Connections Here, the Ethernet interfaces of the Spectra PowerBox 100-IoT can be configured. The colour indicator next to each interface designation shows whether an active network cable is applied to the interface or not. In the as delivered state, both ETH interfaces are configured so that the IPv4 address is automatically obtained via DHCP.
- Page 73 The currently obtained IP address is indicated in the corresponding fields. To reload the screen, you must possibly access the “Network Configuration” menu item again and click on the “Wired Connections” tab. Spectra GmbH & Co. KG User Manual Version 1.1 vertrieb@spectra.de...
- Page 74 The Web interface checks the entered addresses for plausibility. However, the topology of the network landscape must always be assessed by an administrator and/or system integrator which is familiar with the network. Spectra GmbH & Co. KG User Manual Version 1.1 vertrieb@spectra.de...
-
Page 75: Data Backup
Desktop settings and profile of the user “pbgui” The screen allows for • starting a backup run • accessing a list of earlier backups saved on the Spectra PowerBox 100-IoT • downloading backups • deleting backups Spectra GmbH & Co. KG User Manual Version 1.1... -
Page 76: Restoring The Data Backup
Backups, however, will be maintained. MQTT-Broker Configuration The Spectra PowerBox 100-IoT is equipped with an MQTT-Broker which can be used to deliver messages on the basis of the MQTT protocol. Configuration changes must be saved by clicking on the “Save changes” button. The changes are applied by clicking on the “Apply changes”... -
Page 77: General Settings
Enable the “Unlimited” check box to remove preset restrictions. Spectra GmbH & Co. KG User Manual Version 1.1 vertrieb@spectra.de... -
Page 78: Security
MQTT user account opens up. Here, you must enter the desired user name and a password. The specified login data must now be entered in the corresponding MQTT configurations (devices and/or Node-Red)! Spectra GmbH & Co. KG User Manual Version 1.1 vertrieb@spectra.de... -
Page 79: Ssl/Tls Configuration
Spectra PowerBox 100-IoT. When enabling the SSL/TLS encryption for the first time by checking the “Use SSL/TLS encryption” box, the following dialogue opens up which, however, does not yet include any certificates. Spectra GmbH & Co. KG User Manual Version 1.1 vertrieb@spectra.de... - Page 80 Click on the “Create new Root-CA” button to generate your own certification authority on the Spectra PowerBox 100-IoT. The setting process may take some time. Note: Each click on this button creates new certificates which in turn requires the reconfiguration of the services and devices connected to the broker! The “SSL Listener Port”...
-
Page 81: Shutdown / Reboot
The subject matter of individual license conditions is that the source codes must also be made accessible. On a case-by-case basis, Spectra GmbH & Co. KG refers to the publicly available source code archives of each software project (Github, Sourceforge, etc.). Some of the binary software components are the intellectual property of Spectra GmbH &... -
Page 82: Chapter 6 Iiot Surface
CHAPTER 6 IIoT SURFACE... -
Page 83: General
6.1 General The operating system of the Spectra PowerBox 100-IoT has a graphic user interface which allows for the easy use of the system without extensive Linux knowledge and on the basis of the user-friendliness which you know from the standard operating systems in your office environment. -
Page 84: Settings
6.3.1 Screen Resolution The screen resolution can be set as follows: Start the “Settings Manager” via the Start button -> Settings. Now you can make the desired settings in the “Display” item. Spectra GmbH & Co. KG User Manual Version 1.1 vertrieb@spectra.de... -
Page 85: Wireless Network / Wlan
Now left-click on the desired wireless network in the left column and press the “Connect” button. Here you can also define whether the IP address is to be assigned statically or configured by the DHCP server. Spectra GmbH & Co. KG User Manual Version 1.1 vertrieb@spectra.de... -
Page 86: Desktop Symbols
In the as delivered state, there are shortcut icons on the desktop. • Trash: File recycle bin • File system: Access to the file system of the Spectra PowerBox 100-IoT (file manager) • Home: The “User directory” of the user account “pbgui” •... -
Page 87: Chapter 7 Iiot Miscellaneous
CHAPTER 7 IIoT MISCELLANEOUS... -
Page 88: General
7.1 General As already mentioned, no specific Linux knowledge is required for using the Spectra PowerBox 100-IoT. However, in rare cases, the Linux console must be used for some functions and maintenance options. Moreover, it might become necessary to inspect protocols, in particular when developing Node-Red flows. -
Page 89: Acquiring Administrator / Root Rights
7.3.1 Acquiring Administrator / Root Rights Since the operating system of the Spectra PowerBox 100-IoT includes the “sudo” package, you have the choice between three approaches to run commands with the root rights. Any command requiring root rights can be prefixed with ”sudo”. Example: „sudo /etc/init.d/pm2-init.sh restart“... -
Page 90: Operating System Updates
Web interface and offer Node-Red updates. Since the application situation of the Spectra PowerBox 100-IoT as well as the update strategy of the user may be very different, these updates must be installed explicitly. Relating to Node-Red, please note that there might be compatibility issues with existing flows between the different versions and that they should be adjusted at first. - Page 91 If individual services do not work as expected after the update, you should reboot the Spectra PowerBox 100-IoT. As described above, the operating status of the relevant services can be viewed via the start page of the Web interface.
- Page 92 CHAPTER 8 IIoT NODE- RED...
-
Page 93: Node-Red Programming
Node-Red editor, the process logics must be individually programmed in most of the cases due to the diversity of data structures. The user manual of the Spectra PowerBox 100-IoT can only cover the technical operation of Node-Red, also for reasons of topicality. Since Node-Red is continuously developing, the online documentation should be the first source for details on Node-Red nodes and flow programming. -
Page 94: Viewing The Node-Red Runtime Log
The Node-Red process can be stopped by running the command pm2 stop node-red. 8.2.4 Starting the Node-Red Process The Node-Red process can be started by running the command pm2 start node-red. Spectra GmbH & Co. KG User Manual Version 1.1 vertrieb@spectra.de... -
Page 95: Activities For Repairing Node-Red Instances Not Starting
Optionally, you may try to remove the error from the flow file and then restart the process. In general, it is also possible to import a backup via the Web interface thus restoring functional operation. Spectra GmbH & Co. KG User Manual Version 1.1 vertrieb@spectra.de... - Page 96 Spectra GmbH & Co. KG Sales Offices Phone +49 (0) 7121 1432 + ext. Mahdenstr. 3 North 06, 10-31, 38-39 -148 72768 Reutlingen Center 32-37, 40-54, 56-59 -123 Germany Southwest-West 55, 60-69, 72000-72519, 72700-72999, 75-79, 87-88 -155 +49 (0) 7121 1432-10...
Need help?
Do you have a question about the PowerBox 100-IoT-J19 and is the answer not in the manual?
Questions and answers