Replacing Main Controller Pcb; When Replacing The Sram Pcb; When Replacing The Hdd - Canon imagerunner C5180 Service Manual

LDADJ5-Y/M/C/K
LDADJ6-Y/M/C/K
Patch Constants Adjustment
COPIER > OPTION > BODY > P-ALPHA
Write Start Position Adjustment (Margin along
leading edge of image)
COPIER > ADJUST > FEED-ADJ > REGIST
Duplexing Side Registration Adjustment
COPIER > ADJUST > FEED-ADJ > ADJ-REFE
Duplexing Write Start Position Adjustment
COPIER > ADJUST > FEED-ADJ > REGIST2
Adjustment of Paper Width Standard Value of
Manual Feed Tray
COPIER > ADJUST > CST-ADJ > MF-A4R
COPIER > ADJUST > CST-ADJ > MF-A6R
COPIER > ADJUST > CST-ADJ > MF-A4
Adjusting the paper width standard value of the
manual feed tray.
3)Turn OFF/ON the main power switch.

16.6.3 Replacing Main Controller PCB

After mounting the main controller PCB (main),
mount each PCB that is removed before the
replacement.
[1] Main Controller PCB (Sub R-A)
[2] Main Controller PCB (Sub PDEM-EF-A)
[3] Main Controller PCB (Sub SJ-A)
[4] Main Controller PCB (Sub LAN-bar-A)
[5] Storage of program for BOOT ROM BOOT
[6] SRAM PCB
[7] DDR-SDRAM
[8] Main Controller PCB (Sub RB-A)
[9] HDD
[9]
[8] [7]
F-16-39
16.6.4 When Replacing the SRAM
PCB
When the SRAM PCB is replaced, all data in its
memory will be lost (file-related, user mode-related,
service mode-related, history-related files). There
will be no error operation, and initialization will take
place automatically.
If you pull out the SRAM PCB from machine B and
mount it to machine A, the PCB will be initialized
and be rendered useless for machine A or B. Take
full care.
1) When you turn on the power after replacing the
SRAM PCB, the machine will perform automatic
initialization and will indicate a message on its
panel to the effect that you are to turn off and then
on the power switch found on its right side.
Follow the message and turn off and then on the
machine.
2) Using service mode, initialize the RAM.
COPIER>FUNCTION>CLEAR>MN-CON
Before starting the work, be sure to inform the user
that all image data stored in the Box will be lost and
obtain his/her consent.
[1]

16.6.5 When Replacing the HDD

[2]
1. If NetSpot Accountant (NSA) Is Not Used
[2]
1) Formatting the HDD
While holding down the 2 and 8 keys on the
[3]
control panel, turn on the power to start up. Using
the HD formatting function of the SST, format all
partitions.
2) Downloading the Software
[4]
Using the SST, download the various software
(system, language, RUI). The machine will take
about 10 min to start up after downloading.
[5]
2. If NetSpot Accountant (NSA) Is Used Together
with a Card Reader
The card ID used by the NSA resides on the HDD. If
you have replaced the HDD, therefore, you will have
to newly download the card data from NSA to enable
the statistical operations of NSA. After going
through steps 1) and 2) above, perform the
following:
[6]
1) Set the following in service mode:
Select the following : COPIER >FUNCTION
>INSTALL >CARD; then, enter the number of
the first card, and press [OK].
(For instance, if cards No. 1 through No. 1000 are
Chapter 16
16-15