Makita DLS714 Instruction Manual page 4

2. Do not use the power tool if the switch does not turn
it on and off.
with the switch is dangerous and must be repaired.
3. Disconnect the plug from the power source and/or
the battery pack from the power tool before making
any adjustments, changing accessories, or storing
power tools.
the risk of starting the power tool accidentally.
4. Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool
or these instructions to operate the power tool.
tools are dangerous in the hands of untrained users.
5. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool's operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
6. Keep cutting tools sharp and clean.
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
7. Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to be
performed.
from those intended could result in a hazardous situation.
Battery tool use and care
1.
the manufacturer.
when used with another battery pack.
2.
nated battery packs.
3. When battery pack is not in use, keep it away from
other metal objects, like paper clips, coins, keys, nails,
screws or other small metal objects, that can make a
connection from one terminal to another.
4. Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact acciden-
additionally seek medical help.
the battery may cause irritation or burns.
Service
1.
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
2. Follow instruction for lubricating and chang-
ing accessories.
3. Keep handles dry, clean and free from oil and grease.
Cordless miter saw safety warnings
1. Keep hands out of path of saw blade. Avoid contact
with any coasting blade. It can still cause severe injury.
2. Check the saw blade carefully for cracks or
deformation before operation.
Replace damaged blades immediately.
3. Replace the kerf board when worn.
4.
turer which conform to EN847-1.
5. Do not use saw blades manufactured from
high speed steel.
6. Wear eye protection.
7. Wear hearing protection to reduce the risk of
hearing loss.
8. Wear gloves for handling saw blade (saw
blades shall be carried in a holder wherever
practicable) and rough material.
9. Connect miter saws to a dust collecting device
when sawing.
10. Select saw blades in relation to the material to be cut.
11. Always secure all moving portions before car-
rying the tool. When lifting or carrying the tool,
do not use the guard as a carrying handle.
12. Do not operate saw without guards in place. Check
blade guard for proper closing before each use. Do
not operate saw if blade guard does not move freely
and close instantly. Never clamp or tie the blade
guard into the open position.
13.
chips and cut-offs.
14. Use only saw blades that are marked with a
maximum speed equal to or higher than the no
load speed marked on the tool.
15.
not replace the laser or LED with a different
type.
16. Never remove any cut-offs or other parts of the
workpiece from the cutting area whilst the tool
is running with an unguarded saw blade.
17. Do not perform any operation freehand. The work-
guide fence with the vise during all operations. Never
-
use your hand to secure the workpiece.
18. Ensure that the tool is stable before each cut.
19. Fix the tool to a work bench, if needed.
20. Support long workpieces with appropriate
additional supports.
21. Never cut so small workpiece which cannot be
securely held by the vise. Improperly held workpiece
22. Never reach around saw blade.
23. Turn off tool and wait for saw blade to stop before
moving workpiece or changing settings.
24. Disconnect the plug from the power source
and/or the battery pack from the power tool
before changing blade or servicing.
25. Stopper pin which locks the cutter head down
is for carrying and storage purposes only and
not for any cutting operations.
26.
ble liquids or gases. The electrical operation of
27.
28.
cially the installing surface) or bolt. Damage to
these parts could result in blade breakage.
29. Make sure that the turn base is properly
secured so it will not move during operation.
30. For your safety, remove the chips, small
-
pieces, etc. from the table top before
operation.
31. Avoid cutting nails. Inspect for and remove all
nails from the workpiece before operation.
4 ENGLISH
-
-