• EXPORT RESTRICTIONS. You acknowledge that SOFTWARE is subject to U.S. export jurisdiction. You agree to comply with all applicable international and national laws that apply to the SOFTWARE, including U.S. Export Administration Regulations, as well as end-user, end-use and destination restrictions issued by U.S. and other governments. For additional information see http://www.microsoft.com/exporting/. Accent 800/800-D Getting Started...
Disabling and Enabling the Toolbox..........................21 Backing up Your Vocabularies ............................. 21 Updating the NuVoice Software via a Wi-Fi Connection ..................... 22 Updating the NuVoice Software via USB Flash Drive ....................22 Finding Additional Information............................ 22 Accent 800/800-D Getting Started...
Y-adapter. If you have a joystick plugged in and it does not respond normally, reverse the way it is plugged in (plug switch A into jack B, switch B into jack A). Accent 800/800-D Getting Started...
If you use a switch or switches for access to your device, plug them into switch jacks A and B. To use a joystick, you will need a Y-adapter. If you have a joystick plugged in and it does not respond normally, reverse the way it is plugged in (plug switch A into jack B, switch B into jack A). Accent 800/800-D Getting Started...
1. Place the device face-down on a flat surface. 2. Rotate the stand away from the back of the device. 3. The legs will latch into place in the holders at the top of each leg. Wire stand legs latched in place Accent 800/800-D Getting Started...
5. Pull the stand free and put it in a safe place in case you need to use it later. Important! If you reattach the stand, be sure to secure the legs with the holders to prevent someone from pulling it loose accidentally. Accent 800/800-D Getting Started...
Mini USB Connector. See “To Reattach the Handle” below. To Reattach the Handle Remove the port cover, line up the holes in the handle with the holes on the back of the device, and insert the two screws. Accent 800/800-D Getting Started...
Remove the two screws that hold the port cover in place. Use the screws to mount a NuPoint module or to reattach the handle. Note: Store the port cover where you can find it if you need to use it again. Accent 800/800-D Getting Started...
2. Grasp one side of the frame and pull it loose 3. Pull the top and bottom tabs loose. from the device. Hint: You may want to use a flat-head screwdriver or a similar tool. 4. Pull the other side loose. Accent 800/800-D Getting Started...
Transporting the device in a carry case may also wake it. In that case, power off the device. Note: To change power button operation in the NuVoice software, see “Managing Power Settings” in the Accent 800 Hardware Manual. Download the manual from https://www.prentrom.com/support/accent. Restarting the Device Recommendation: Restart your device once per week.
If the device is on: The battery/charging LED will glow yellow. When the device is fully charged, the LED will turn green. If the device is off: The battery/charging LED will glow yellow. When the device is fully charged, • the LED will turn off. Accent 800/800-D Getting Started...
Try using the device. If it does not work, call the PRC Service Department and tell them what happened. They may ask you to send in your device for servicing. Accent 800/800-D Getting Started...
Page 15
TouchGuide, Keyguard, etc.) with glass cleaner, so the screen doesn’t discolor. 2. Allow the equipment to dry. For complete device information, instructions, and troubleshooting, download the Accent 800 Hardware Manual at www.prentrom.com/support. Select Device and Accessory Manuals, select the appropriate device, and select the download you want.
6. When the question “Switch to this User Area now?” appears, answer Yes or No. 7. Select OK twice to return to the vocabulary screen. 8. If you want to load all three LAMP WFL vocabularies, follow these same steps, selecting a different user area for each. Accent 800/800-D Getting Started...
Page 17
Unity-configured device, Essence vocabularies and settings can be loaded as a product configuration. To configure the device for the Essence language system, follows steps 1-5 under “CoreScanner” above, substituting Essence for CoreScanner in step 3. Accent 800/800-D Getting Started...
2. Select Replace User Area and then select the vocabulary you want to replace. 3. Select the vocabulary folder. Then select the specific vocabulary you want. 4. Select Yes in the yellow message box to continue. Accent 800/800-D Getting Started...
When the pronunciation is correct, select OK. The word will be listed on the Manage Pronunciations screen. Note: You can test the pronunciation of any word listed on the Manage Pronunciations screen by selecting Test Pronunciation. 8. Select OK to exit the Manage Pronunciations screen. Accent 800/800-D Getting Started...
4. Select Save as Icon. 5. Select Rename Icon, select Clear Display, type a name, select OK, and select OK again. 6. Select a category or select Cancel to send it to the Imports folder. 7. Select OK. Accent 800/800-D Getting Started...
5. Make sure the pre-set folder is a USB drive. If so, select OK. Type the file name and date (xx-xx-xx). 6. Select OK and wait for the information to be transferred. When the transfer is complete, select OK. Accent 800/800-D Getting Started...
11. When the update process is finished, remove the USB flash drive from your device. Note: Once your device is running the updated software, you can unplug the battery charger. Finding Additional Information For complete device information, instructions, and troubleshooting, download the Accent 800 Hardware Manual from https://www.prentrom.com/support/accent. Accent 800/800-D Getting Started...