Page 1 Title Page Grid Solutions M60 Motor Protection System UR Series Instruction Manual M60 Revision: 5.8x Manual P/N: 1601-0108-V2 (GEK-113558A) Copyright © 2017 GE Multilin Inc. 833711A2.CDR E83849 GE Grid Solutions LISTED 650 Markland Street IND.CONT. EQ. 52TL Markham, Ontario GE Multilin's Quality Management...
Page 3 GEK-113558A (revision V2) but are not included in the current M60 operations. The following functions and items are not yet available with the current version of the M60 relay: • Signal sources SRC 5 and SRC 6.
Page 5: Table Of Contents
1.3 ENERVISTA UR SETUP SOFTWARE 1.3.1 PC REQUIREMENTS ..................1-6 1.3.2 INSTALLATION....................1-6 1.3.3 CONFIGURING THE M60 FOR SOFTWARE ACCESS........1-8 1.3.4 USING THE QUICK CONNECT FEATURE............. 1-10 1.3.5 CONNECTING TO THE M60 RELAY .............. 1-16 1.4 UR HARDWARE 1.4.1 MOUNTING AND WIRING................
Page 6 MANAGED ETHERNET SWITCH MODULE HARDWARE......3-48 3.4.3 MANAGED SWITCH LED INDICATORS ............3-49 3.4.4 CONFIGURING THE MANAGED ETHERNET SWITCH MODULE ....3-49 3.4.5 UPLOADING M60 SWITCH MODULE FIRMWARE.........3-52 3.4.6 ETHERNET SWITCH SELF-TEST ERRORS...........3-54 4. HUMAN INTERFACES 4.1 ENERVISTA UR SETUP SOFTWARE INTERFACE 4.1.1 INTRODUCTION ....................4-1...
Page 7 DIRECT INPUTS AND OUTPUTS ..............5-227 5.8.11 TELEPROTECTION INPUTS AND OUTPUTS..........5-230 5.8.12 IEC 61850 GOOSE ANALOGS..............5-232 5.8.13 IEC 61850 GOOSE INTEGERS..............5-234 5.9 TRANSDUCER INPUTS AND OUTPUTS 5.9.1 DCMA INPUTS ....................5-235 GE Multilin M60 Motor Protection System...
Page 8 MODEL INFORMATION ...................6-27 6.5.2 FIRMWARE REVISIONS..................6-27 7. COMMANDS AND 7.1 COMMANDS TARGETS 7.1.1 COMMANDS MENU ...................7-1 7.1.2 VIRTUAL INPUTS ....................7-1 7.1.3 CLEAR RECORDS .....................7-2 7.1.4 SET DATE AND TIME ..................7-2 7.1.5 RELAY MAINTENANCE ..................7-3 viii M60 Motor Protection System GE Multilin...
Page 9 STORE MULTIPLE SETTINGS (FUNCTION CODE 10H) ........B-5 B.2.6 EXCEPTION RESPONSES ................B-5 B.3 FILE TRANSFERS B.3.1 OBTAINING RELAY FILES VIA MODBUS ............B-6 B.3.2 MODBUS PASSWORD OPERATION ...............B-7 B.4 MEMORY MAPPING B.4.1 MODBUS MEMORY MAP .................B-8 B.4.2 DATA FORMATS .....................B-67 GE Multilin M60 Motor Protection System...
Page 10 DNP V3.00 DEVICE PROFILE ................E-1 E.1.2 IMPLEMENTATION TABLE ................E-4 E.2 DNP POINT LISTS E.2.1 BINARY INPUT POINTS ................... E-8 E.2.2 BINARY AND CONTROL RELAY OUTPUT............E-9 E.2.3 COUNTERS..................... E-10 E.2.4 ANALOG INPUTS.................... E-11 M60 Motor Protection System GE Multilin...
Page 11 TABLE OF CONTENTS F. MISCELLANEOUS F.1 CHANGE NOTES F.1.1 REVISION HISTORY ..................F-1 F.1.2 CHANGES TO THE M60 MANUAL ..............F-2 F.2 ABBREVIATIONS F.2.1 STANDARD ABBREVIATIONS ................. F-6 F.3 WARRANTY F.3.1 GE MULTILIN WARRANTY ................F-8 INDEX GE Multilin M60 Motor Protection System...
Page 12 TABLE OF CONTENTS M60 Motor Protection System GE Multilin...
Page 13: Getting Started
Product disassembly and repairs are not permitted. All service needs to be conducted by the factory. This product is rated to Class A emissions levels and is to be used in Utility, Substation Industrial environments. Not to be used near electronic devices rated for Class B levels. GE Multilin M60 Motor Protection System...
Page 14: Inspection Checklist
• Mounting screws. For product information, instruction manual updates, and the latest software updates, please visit the GE Grid Solutions website. If there is any noticeable physical damage, or any of the contents listed are missing, contact GE Multilin immedi- ately. NOTE...
Page 15: Ur Overview
This new generation of equipment must also be easily incorporated into automation systems, at both the station and enterprise levels. The GE Multilin Universal Relay (UR) has been developed to meet these goals. GE Multilin...
Page 16: Hardware Architecture
(dual) ring configuration. This feature is optimized for speed and intended for pilot- aided schemes, distributed logic applications, or the extension of the input/output capabilities of a single relay chassis. M60 Motor Protection System GE Multilin...
Page 17: Software Architecture
Employing OOD/OOP in the software architecture of the M60 achieves the same features as the hardware architecture: modularity, scalability, and flexibility. The application software for any UR-series device (for example, feeder protection, transformer protection, distance protection) is constructed by combining objects from the various functionality classes.
Page 18: Enervista Ur Setup Software
Video capable of displaying 800 x 600 or higher in high-color mode (16-bit color) • RS232 and/or Ethernet port for communications to the relay The following qualified modems have been tested to be compliant with the M60 and the EnerVista UR Setup software. • US Robotics external 56K FaxModem 5686 •...
Page 19 Install Software window as shown below. Select the “Web” option to ensure the most recent software release, or select “CD” if you do not have a web connection, then click the Add Now button to list software items for the M60.
Page 20: Configuring The M60 For Software Access
OVERVIEW The user can connect remotely to the M60 through the rear RS485 port or the rear Ethernet port with a PC running the EnerVista UR Setup software. The M60 can also be accessed locally with a laptop computer through the front panel RS232 port or the rear Ethernet port using the Quick Connect feature.
Page 21 SERIAL PORTS 10. Click the Read Order Code button to connect to the M60 device and upload the order code. If an communications error occurs, ensure that the EnerVista UR Setup serial communications values entered in the previous step corre- spond to the relay setting values.
Page 22: Using The Quick Connect Feature
MODBUS PROTOCOL 11. Click the Read Order Code button to connect to the M60 device and upload the order code. If an communications error occurs, ensure that the three EnerVista UR Setup values entered in the previous steps correspond to the relay setting values.
Page 23 M60. This ensures that configuration of the EnerVista UR Setup software matches the M60 model number. b) USING QUICK CONNECT VIA THE REAR ETHERNET PORTS To use the Quick Connect feature to access the M60 from a laptop through Ethernet, first assign an IP address to the relay from the front panel keyboard.
Page 24 Right-click the Local Area Connection icon and select Properties. Select the Internet Protocol (TCP/IP) item from the list provided and click the Properties button. Click on the “Use the following IP address” box. 1-12 M60 Motor Protection System GE Multilin...
Page 25 1 GETTING STARTED 1.3 ENERVISTA UR SETUP SOFTWARE Enter an IP address with the first three numbers the same as the IP address of the M60 relay and the last number dif- ferent (in this example, 1.1.1.2). Enter a subnet mask equal to the one set in the M60 (in this example, 255.0.0.0).
Page 26 If this computer is used to connect to the Internet, re-enable any proxy server settings after the laptop has been discon- nected from the M60 relay. Verify that the latest version of the EnerVista UR Setup software is installed (available from the GE enerVista CD or online from http://www.gegridsolutions.com/multilin). See the Software Installation section for installation details.
Page 27 Each time the EnerVista UR Setup software is initialized, click the Quick Connect button to establish direct communica- tions to the M60. This ensures that configuration of the EnerVista UR Setup software matches the M60 model number. When direct communications with the M60 via Ethernet is complete, make the following changes: From the Windows desktop, right-click the My Network Places icon and select Properties to open the network con- nections window.
Page 28: Connecting To The M60 Relay
The EnerVista UR Setup software has several new quick action buttons that provide users with instant access to several functions that are often performed when using M60 relays. From the online window, users can select which relay to interro- gate from a pull-down window, then click on the button for the action they wish to perform. The following quick action func- tions are available: •...
Page 29: Ur Hardware
Figure 1–7: RELAY COMMUNICATIONS OPTIONS To communicate through the M60 rear RS485 port from a PC RS232 port, the GE Multilin RS232/RS485 converter box is required. This device (catalog number F485) connects to the computer using a “straight-through” serial cable. A shielded twisted-pair (20, 22, or 24 AWG) connects the F485 converter to the M60 rear communications port.
Page 30: Using The Relay
LED off. The relay in the “Not Programmed” state will block signaling of any output relay. These conditions will remain until the relay is explicitly put in the “Programmed” state. Select the menu message    SETTINGS PRODUCT SETUP INSTALLATION RELAY SETTINGS RELAY SETTINGS: Not Programmed 1-18 M60 Motor Protection System GE Multilin...
Page 31: Relay Passwords
See the Changing Settings section in Chapter 4 for complete instructions on setting up security level passwords. NOTE 1.5.6 FLEXLOGIC™ CUSTOMIZATION FlexLogic™ equation editing is required for setting up user-defined logic for customizing the relay operations. See the Flex- Logic™ section in Chapter 5 for additional details. GE Multilin M60 Motor Protection System 1-19...
Page 32: Commissioning
1 GETTING STARTED 1.5.7 COMMISSIONING The M60 requires a minimum amount of maintenance when it is commissioned into service. Since the M60 is a micropro- cessor-based relay, its characteristics do not change over time. As such, no further functional tests are required.
Page 33: Product Description
Another option provides two 10Base-F fiber optic ports for redundancy. The Ethernet port supports IEC 61850, Modbus TCP, and TFTP protocols, and allows access to the relay via any standard web browser (M60 web pages). The IEC 60870- 5-104 protocol is supported on the Ethernet port. DNP 3.0 and IEC 60870-5-104 cannot be enabled at the same time.
Page 34 DNP 3.0 or IEC 60870-5-104 protocol Reduced Voltage Starting Virtual Inputs (64) Ethernet Global Data Protocol (optional) Remote RTD Protection Virtual Outputs (96) Event Recorder RTD Inputs VT Fuse Failure FlexElements™ (16) RTD Protection M60 Motor Protection System GE Multilin...
Page 35: Ordering
2.1.2 ORDERING a) OVERVIEW The M60 is available as a 19-inch rack horizontal mount or reduced-size (¾) vertical unit and consists of the following mod- ules: power supply, CPU, CT/VT, digital input and output, transducer input and output, and inter-relay communications.
Page 36 2 PRODUCT DESCRIPTION b) ORDER CODES WITH TRADITIONAL CTS AND VTS The order codes for the horizontal mount units with traditional CTs and VTs are shown below. Table 2–3: M60 ORDER CODES (HORIZONTAL UNITS) * - F - W/X Full Size Horizontal Mount...
Page 37 2.1 INTRODUCTION The order codes for the reduced size vertical mount units with traditional CTs and VTs are shown below. Table 2–4: M60 ORDER CODES (REDUCED SIZE VERTICAL UNITS) * - F Reduced Size Vertical Mount (see note regarding P/R slot below)
Page 38 2 PRODUCT DESCRIPTION c) ORDER CODES WITH PROCESS BUS MODULES The order codes for the horizontal mount units with the process bus module are shown below. Table 2–5: M60 ORDER CODES (HORIZONTAL UNITS WITH PROCESS BUS) * - F - W/X...
Page 39: Replacement Modules
Replacement modules can be ordered separately as shown below. When ordering a replacement CPU module or face- plate, please provide the serial number of your existing unit. Not all replacement modules may be applicable to the M60 relay. Only the modules specified in the order codes are available as replacement modules.
Page 40 4 dcmA inputs, 4 dcmA outputs (only one 5A or 5D module is allowed) 8 RTD inputs INPUTS/OUTPUTS 4 RTD inputs, 4 dcmA outputs (only one 5A or 5D module is allowed) 4 dcmA inputs, 4 RTD inputs 8 dcmA inputs M60 Motor Protection System GE Multilin...
Page 41 4 dcmA inputs, 4 dcmA outputs (only one 5A or 5D module is allowed) 8 RTD inputs INPUTS/OUTPUTS 4 RTD inputs, 4 dcmA outputs (only one 5A or 5D module is allowed) 4 dcmA inputs, 4 RTD inputs 8 dcmA inputs GE Multilin M60 Motor Protection System...
Page 42: Protection Elements
1.00 to 1.50 in steps of 0.01 Inverse; IEC (and BS) A/B/C and Short Motor full load current (FLA): 0.050 to 1.000 pu in steps of 0.001 Inverse; GE IAC Inverse, Short/Very/ Standard overload curve, cutoff effect: Extremely Inverse; I t;...
Page 43 CT rating: ±1.5% of reading Pickup delay: 0.10 to 600.00 s in steps of 0.01 Reset delay: 0.00 to 600.00 s in steps of 0.01 Time accuracy: ±3% or ±20 ms, whichever is greater GE Multilin M60 Motor Protection System 2-11...
Page 44 Level accuracy: ±0.5% of reading from 10 to 208 V Dropout level: pickup + 0.03 Hz Curve shapes: GE IAV Inverse, Definite Time Level accuracy: ±0.001 Hz Curve multiplier: Time Dial = 0 to 600.00 in steps of 0.01 Time delay: 0 to 65.535 s in steps of 0.001...
Page 45: User-Programmable Elements
Power-up mode: restore from non-volatile memory or syn- Output: stored in non-volatile memory chronize to a 3-bit control input or synch/ Execution sequence: as input prior to protection, control, and restore mode FlexLogic™ GE Multilin M60 Motor Protection System 2-13...
Page 46: Monitoring
±0.001 Hz (when voltage signal is used Accuracy: ±1.0% of reading for frequency measurement) I = 0.1 to 0.25 pu: ±0.005 Hz I > 0.25 pu: ±0.001 Hz (when current signal is used for frequency measurement) 2-14 M60 Motor Protection System GE Multilin...
Page 47: Inputs
1 to 1000 in steps of 1 Unreturned message alarm: Responding to: Rate of unreturned messages in the ring configuration Monitoring message count: 10 to 10000 in steps of 1 Alarm threshold: 1 to 1000 in steps of 1 GE Multilin M60 Motor Protection System 2-15...
Page 48: Power Supply
95% voltage drop across the load impedance. Trickle current: approx. 1 to 2.5 mA Operate time: < 0.6 ms FORM-A CURRENT MONITOR Internal Limiting Resistor: 100 Ω, 2 W Threshold current: approx. 80 to 100 mA GE Multilin M60 Motor Protection System 2-16...
Page 49 Isolation: ±300 Vpk Internal fuse: 5 A / 350 V AC, Ceramic, Axial SLO REMOTE OUTPUTS (IEC 61850 GSSE/GOOSE) BLO; Standard output points: 32 Manufacturer: Conquer; Part number: SCD-A 005 User output points: GE Multilin M60 Motor Protection System 2-17...
Page 50: Communications
Shielded twisted pair: 150 m (492 ft.) MAXIMUM STANDARD FAST ETHERNET SEGMENT LENGTHS 10Base-T (CAT 3, 4, 5 UTP): 100 m (328 ft.) 100Base-TX (CAT 5 UTP):100 m (328 ft.) Shielded twisted pair: 150 m (492 ft.) 2-18 M60 Motor Protection System GE Multilin...
Page 51: Inter-Relay Communications
At extreme temperatures these values deviate based on component tolerance. On average, the output power decreases as the temperature is increased by a factor 1dB / 5°C. GE Multilin M60 Motor Protection System 2-19...
Page 52: Environmental
Operating temperature: –40 to 60°C; the LCD contrast may be Pollution degree: impaired at temperatures less than – Overvoltage category: 20°C Ingress protection: IP20 front, IP10 back HUMIDITY Humidity: operating up to 95% (non-condensing) at 55°C (as per IEC60068-2-30 variant 1, 6days). 2-20 M60 Motor Protection System GE Multilin...
Page 53: Type Tests
20 V/m, 80 MHz to 1 GHz Safety UL508 e83849 NKCR Safety UL C22.2-14 e83849 NKCR7 Safety UL1053 e83849 NKCR 2.2.12 PRODUCTION TESTS THERMAL Products go through an environmental test based upon an Accepted Quality Level (AQL) sampling process. GE Multilin M60 Motor Protection System 2-21...
Page 54: Approvals
Normally, cleaning is not required; but for situations where dust has accumulated on the faceplate display, a dry cloth can be used. Units that are stored in a de-energized state should be powered up once per year, for one hour continuously, to avoid deterioration of electrolytic capacitors. NOTE 2-22 M60 Motor Protection System GE Multilin...
Page 55: Hardware
HORIZONTAL UNITS The M60 Motor Protection System is available as a 19-inch rack horizontal mount unit with a removable faceplate. The faceplate can be specified as either standard or enhanced at the time of ordering. The enhanced faceplate contains addi- tional user-programmable pushbuttons and LED indicators.
Page 56 VERTICAL UNITS The M60 Motor Protection System is available as a reduced size (¾) vertical mount unit, with a removable faceplate. The faceplate can be specified as either standard or enhanced at the time of ordering. The enhanced faceplate contains addi- tional user-programmable pushbuttons and LED indicators.
Page 57 RS232 communications port. The relay is secured to the panel with the use of four screws supplied with the relay. 11.015” 7.482” 1.329” 13.560” 15.000” 14.025” 4.000” 9.780” 843809A1.CDR Figure 3–4: M60 VERTICAL DIMENSIONS (ENHANCED PANEL) GE Multilin M60 Motor Protection System...
Page 58 UR SERIES UR SERIES Figure 3–5: M60 VERTICAL MOUNTING AND DIMENSIONS (STANDARD PANEL) For details on side mounting M60 devices with the enhanced front panel, refer to the following documents available online from the GE Grid Solutions website. • GEK-113180: UR-series UR-V side-mounting front panel assembly instructions.
Page 59 3 HARDWARE 3.1 DESCRIPTION Figure 3–6: M60 VERTICAL SIDE MOUNTING INSTALLATION (STANDARD PANEL) GE Multilin M60 Motor Protection System...
Page 60: Module Withdrawal And Insertion
The enhanced faceplate can be opened to the left, once the thumb screw has been removed, as shown below. This allows for easy accessibility of the modules for withdrawal. The new wide-angle hinge assembly in the enhanced front panel opens completely and allows easy access to all modules in the M60. M60 Motor Protection System...
Page 61 When the clips have locked into position, the module will be fully inserted. All CPU modules except the 9E are equipped with 10/100Base-T or 100Base-F Ethernet connectors. These con- nectors must be individually disconnected from the module before it can be removed from the chassis. NOTE GE Multilin M60 Motor Protection System...
Page 62: Rear Terminal Layout
3.1 DESCRIPTION 3 HARDWARE The 4.0x release of the M60 relay includes new hardware modules.The new CPU modules are specified with codes 9E and higher. The new CT/VT modules are specified with the codes 8F and higher. NOTE The new CT/VT modules can only be used with new CPUs; similarly, old CT/VT modules can only be used with old CPUs.
Page 63 (rows 1 to 8), use a minimum of 17 inch-pounds. During manufacturing, the power supply and CPU modules are installed in slots B and D of the chassis with 13 inch-pounds of torque on the screws at the top and bottom of the modules. GE Multilin M60 Motor Protection System...
Page 64: Wiring
Please GROUNDED IF GROUND refer to the Instruction Manual for additional details on (Rear View) TERMINAL IS PROVIDED wiring based on various configurations. * Optional * Optional Figure 3–12: TYPICAL WIRING DIAGRAM 3-10 M60 Motor Protection System GE Multilin...
Page 65: Dielectric Strength
(see the Self-test errors section in chapter 7) or control power is lost, the relay will de-energize. For high reliability systems, the M60 has a redundant option in which two M60 power supplies are placed in parallel on the bus.
Page 66: Ct/Vt Modules
Figure 3–13: CONTROL POWER CONNECTION When using an SH/SL power supply module or a M60 with the HardFiber system, before powering off the M60, save data in the compact flash memory using Commands > Relay Maintenance > Save Non-Volatile Data. When NOTE not saved or the relay loses power, up to the last two minutes of data is not saved to the compact flash memory.
Page 67 Substitute the tilde “~” symbol with the slot position of the module in the following figure. NOTE Current inputs Voltage inputs 8F, 8G, 8L, and 8M modules (4 CTs and 4 VTs) Current inputs 8H, 8J, 8N, and 8R modules (8 CTs) 842766A3.CDR Figure 3–15: CT/VT MODULE WIRING GE Multilin M60 Motor Protection System 3-13...
Page 68: Process Bus Modules
3.2.5 PROCESS BUS MODULES The M60 can be ordered with a process bus interface module. This module is designed to interface with the GE Multilin HardFiber system, allowing bi-directional IEC 61850 fiber optic communications with up to eight HardFiber merging units, known as Bricks.
Page 69 Wherever a tilde “~” symbol appears, substitute with the slot position of the module; wherever a number sign “#” appears, substitute the contact number NOTE GE Multilin M60 Motor Protection System 3-15...
Page 70: M60 Motor Protection System
Form-C ~6a, ~6c 2 Inputs Fast Form-C ~7a, ~7c 2 Inputs ~7a, ~7c 2 Inputs ~7a, ~7c 2 Inputs Fast Form-C ~8a, ~8c 2 Inputs ~8a, ~8c 2 Inputs ~8a, ~8c 2 Inputs 3-16 M60 Motor Protection System GE Multilin...
Page 71 Not Used ~5a, ~5c 2 Inputs 2 Outputs Solid-State Solid-State ~6a, ~6c 2 Inputs 2 Outputs Not Used Not Used ~7a, ~7c 2 Inputs 2 Outputs Solid-State Solid-State ~8a, ~8c 2 Inputs Not Used GE Multilin M60 Motor Protection System 3-17...
Page 72 3.2 WIRING 3 HARDWARE Figure 3–17: CONTACT INPUT AND OUTPUT MODULE WIRING (1 of 2) 3-18 M60 Motor Protection System GE Multilin...
Page 73 CONTACT IN CONTACT IN COMMON SURGE 842763A2.CDR Figure 3–18: CONTACT INPUT AND OUTPUT MODULE WIRING (2 of 2) Observe correct polarity for all contact input and solid state output connections for proper functional- ity. GE Multilin M60 Motor Protection System 3-19...
Page 74 M60 input even when the output is open, if there is a substantial distributed capacitance (represented by C1) present in the wiring between the output and the M60 input and the debounce time setting in the M60 relay is low enough.
Page 75 This operation of contact inputs also can be prevented by using the Auto-Burnish contact inputs or contact inputs with active impedance. Figure 3–21: CONTACT INPUT CONNECTED TO A CONTACT OUTPUT WITH RESISTOR (R2) ACROSS THE INPUT GE Multilin M60 Motor Protection System 3-21...
Page 76 (EQ 3.2) The 2 mA current is used in case the contact input is connected across the GE Form A contact output with voltage monitoring. Otherwise use the amperage of the active circuit connected to the contact input when its contact output is open and the voltage across the contact input is third trigger threshold to calculate the resistor value.
Page 77 (refer to the Contact Input and Output Module Wiring diagrams). This is beneficial when connecting contact inputs to separate voltage sources. Con- sequently, the threshold voltage setting is also defined per group of two contact inputs. GE Multilin M60 Motor Protection System 3-23...
Page 78 Contact inputs susceptible to parasitic capacitance caused by long cable runs affected by switching surges from external circuits can result in inadvertent activation of contact inputs with the external contact open. In this case, GE recommends using the digital I/O module with active impedance circuit.
Page 79 3 HARDWARE 3.2 WIRING Figure 3–24: ACTIVE IMPEDANCE CONTACT INPUT V-I CHARACTERISTIC GE Multilin M60 Motor Protection System 3-25...
Page 80: Transducer Inputs/Outputs
(5A, 5C, 5D, 5E, and 5F) and channel arrangements that may be ordered for the relay. Wherever a tilde “~” symbol appears, substitute with the slot position of the module. NOTE Figure 3–25: TRANSDUCER INPUT/OUTPUT MODULE WIRING 3-26 M60 Motor Protection System GE Multilin...
Page 81: Rs232 Faceplate Port
3.2.8 RS232 FACEPLATE PORT A 9-pin RS232C serial port is located on the M60 faceplate for programming with a personal computer. All that is required to use this interface is a personal computer running the EnerVista UR Setup software provided with the relay. Cabling for the RS232 port is shown in the following figure for both 9-pin and 25-pin connectors.
Page 82 For instance, the relays must be connected with all RS485 “+” terminals connected together, and all RS485 “–” terminals connected together. Though data is transmitted over a two-wire twisted pair, all RS485 devices require a shared 3-28 M60 Motor Protection System GE Multilin...
Page 83 This common voltage is implied to be a power supply common. Some systems allow the shield (drain wire) to be used as common wire and to connect directly to the M60 COM terminal (#3); others function cor- rectly only if the common wire is connected to the M60 COM terminal, but insulated from the shield.
Page 84 For optical power budgeting, splices are required every 1 km for the transmitter/receiver pair. When splicing optical fibers, the diameter and numerical aperture of each fiber must be the same. In order to engage or disengage the ST type connec- tor, only a quarter turn of the coupling is required. 3-30 M60 Motor Protection System GE Multilin...
Page 85: Irig-B
UR-series relays can be synchronized. The IRIG-B repeater has a bypass function to maintain the time signal even when a relay in the series is powered down. Figure 3–30: IRIG-B REPEATER Using an amplitude modulated receiver will cause errors up to 1 ms in event time-stamping. NOTE GE Multilin M60 Motor Protection System 3-31...
Page 86: Direct Input/Output Communications
3.3.1 DESCRIPTION The M60 direct inputs and outputs feature makes use of the type 7 series of communications modules. These modules are also used by the L90 Line Differential Relay for inter-relay communications. The direct input and output feature uses the communications channels provided by these modules to exchange digital state information between relays.
Page 87 These modules are listed in the following table. All fiber modules use ST type connectors. Not all the direct input and output communications modules may be applicable to the M60 relay. Only the modules specified in the order codes are available as direct input and output communications modules.
Page 88 Channel 1: G.703, channel 2: 1300 nm, single-mode, laser G.703, 1 channel G.703, 2 channels RS422, 1 channel RS422, 2 channels, 2 clock inputs RS422, 2 channels Observing any fiber transmitter output can cause eye injury. 3-34 M60 Motor Protection System GE Multilin...
Page 89: Fiber: Led And Eled Transmitters
When using a laser Interface, attenuators may be necessary to ensure that you do not exceed the maximum optical input power to the receiver. When using a laser Interface, attenuators may be necessary to ensure that you do not exceed the maximum optical input power to the receiver. GE Multilin M60 Motor Protection System 3-35...
Page 90: Interface
Remove the top cover by sliding it towards the rear and then lift it upwards. Set the timing selection switches (channel 1, channel 2) to the desired timing modes. Replace the top cover and the cover screw. 3-36 M60 Motor Protection System GE Multilin...
Page 91 For connection to a higher order system (UR- to-multiplexer, factory defaults), set to octet timing (S1 = ON) and set timing mode to loop timing (S5 = OFF and S6 = OFF). GE Multilin M60 Motor Protection System 3-37...
Page 92 G.703 line side of the interface while the other lies on the differential Manchester side of the interface. DMR = Differential Manchester Receiver DMX = Differential Manchester Transmitter G7X = G.703 Transmitter G7R = G.703 Receiver 842775A1.CDR Figure 3–41: G.703 DUAL LOOPBACK MODE 3-38 M60 Motor Protection System GE Multilin...
Page 93: Rs422 Interface
1 as shown below. If the terminal timing feature is not available or this type of connection is not desired, the G.703 interface is a viable option that does not impose timing restrictions. GE Multilin M60 Motor Protection System 3-39...
Page 94 Figure 3–44: TIMING CONFIGURATION FOR RS422 TWO-CHANNEL, 3-TERMINAL APPLICATION Data module 1 provides timing to the M60 RS422 interface via the ST(A) and ST(B) outputs. Data module 1 also provides timing to data module 2 TT(A) and TT(B) inputs via the ST(A) and AT(B) outputs. The data module pin numbers have been omitted in the figure above since they may vary depending on the manufacturer.
Page 95: Rs422 And Fiber Interface
When using a laser interface, attenuators can be necessary to ensure that you do not exceed the maximum optical input power to the receiver. Shield Tx – G.703 Rx – channel 1 Tx + Rx + Surge Fiber channel 2 842778A1.CDR Figure 3–47: G.703 AND FIBER INTERFACE CONNECTION GE Multilin M60 Motor Protection System 3-41...
Page 96: Ieee C37.94 Interface
5.60. For customers using firmware release 5.60 and higher, the module can be identified with "Rev D" printed on the module and is to be used on all ends of M60 commu- nication for two and three terminal applications.
Page 97 Once the clips have cleared the raised edge of the chassis, engage the clips simultaneously. When the clips have locked into position, the module will be fully inserted. GE Multilin M60 Motor Protection System 3-43...
Page 98 3.3 DIRECT INPUT/OUTPUT COMMUNICATIONS 3 HARDWARE Figure 3–48: IEEE C37.94 TIMING SELECTION SWITCH SETTING 3-44 M60 Motor Protection System GE Multilin...
Page 99: C37.94Sm Interface
5.60. For customers using firmware release 5.60 and higher, the module can be identified with "Rev D" printed on the module and is to be used on all ends of M60 commu- nication for two and three terminal applications.
Page 100 Once the clips have cleared the raised edge of the chassis, engage the clips simultaneously. When the clips have locked into position, the module will be fully inserted. 3-46 M60 Motor Protection System GE Multilin...
Page 101 3 HARDWARE 3.3 DIRECT INPUT/OUTPUT COMMUNICATIONS Figure 3–49: C37.94SM TIMING SELECTION SWITCH SETTING GE Multilin M60 Motor Protection System 3-47...
Page 102: Managed Ethernet Switch Modules
The type 2S and 2T embedded managed switch modules are supported by UR-series relays containing type 9S CPU mod- ules with revisions 5.5x and higher. The modules communicate to the M60 through an internal Ethernet port (referred to as the UR port or port 7) and provide an additional six external Ethernet ports: two 10/100Base-T ports and four multimode ST 100Base-FX ports.
Page 103: Managed Switch Led Indicators
Switch has been shipped with a default IP address of 192.168.1.2 and a subnet mask of 255.255.255.0. Consult your net- work administrator to determine if the default IP address, subnet mask or default gateway needs to be modified. Do not connect to network while configuring the switch module. GE Multilin M60 Motor Protection System 3-49...
Page 104 SAVING THE ETHERNET SWITCH SETTINGS TO A SETTINGS FILE The M60 allows the settings information for the Ethernet switch module to be saved locally as a settings file. This file con- tains the advanced configuration details for the switch not contained within the standard M60 settings file.
Page 105 Navigate to the folder containing the Ethernet switch settings file, select the file, then click Open. The settings file will be transferred to the Ethernet switch and the settings uploaded to the device. GE Multilin M60 Motor Protection System 3-51...
Page 106: Uploading M60 Switch Module Firmware
NOTE b) SELECTING THE PROPER SWITCH FIRMWARE VERSION The latest switch module firmware is available as a download from the GE Multilin web site. Use the following procedure to determine the version of firmware currently installed on your switch Log into the switch using the EnerVista web interface.
Page 107 Select the firmware file to be loaded on to the Switch, and select the Open option. The following window will pop up, indicating that the firmware file transfer is in progress. If the firmware load was successful, the following window will appear: Note GE Multilin M60 Motor Protection System 3-53...
Page 108: Ethernet Switch Self-Test Errors
No setting required; the M60 EQUIPMENT The M60 has not detected the The M60 failed to see the switch module will read the state of a general MISMATCH: Card XXX presence of the Ethernet on power-up, because switch won’t...
Page 109: Human Interfaces
To start using the EnerVista UR Setup software, a site definition and device definition must first be created. See the EnerV- ista UR Setup Help File or refer to the Connecting EnerVista UR Setup with the M60 section in Chapter 1 for details.
Page 110: Enervista Ur Setup Main Window
Site List window will automatically be sent to the on-line communicating device. g) FIRMWARE UPGRADES The firmware of a M60 device can be upgraded, locally or remotely, via the EnerVista UR Setup software. The correspond- ing instructions are provided by the EnerVista UR Setup Help file under the topic “Upgrading Firmware”.
Page 111 Device data view windows, with common tool bar. Settings file data view windows, with common tool bar. Workspace area with data view tabs. Status bar. 10. Quick action hot links. 842786A3.CDR Figure 4–1: ENERVISTA UR SETUP SOFTWARE MAIN WINDOW GE Multilin M60 Motor Protection System...
Page 112: Extended Enervista Ur Setup Features
(settings file templates) and online devices (online settings templates). The func- tionality is identical for both purposes. The settings template feature requires that both the EnerVista UR Setup software and the M60 firmware are at ver- sions 5.40 or higher.
Page 113 ADDING PASSWORD PROTECTION TO A TEMPLATE GE recommends that templates be saved with password protection to maximize security. When templates are created for online settings, the password is added during the initial template creation step. It does not need to be added after the template is created.
Page 114 Template Mode > View In Template Mode command. The template specifies that only the Pickup Curve Phase time overcurrent settings window without template applied. settings be available. 842858A1.CDR Figure 4–4: APPLYING TEMPLATES VIA THE VIEW IN TEMPLATE MODE COMMAND M60 Motor Protection System GE Multilin...
Page 115 Once a settings template is removed, it cannot be reapplied and a new settings template needs to be defined before use. Right-click the device in the Online or Offline Window area and select the Template Mode > Remove Template option. Enter the template password and click OK to continue. GE Multilin M60 Motor Protection System...
Page 116: Securing And Locking Flexlogic™ Equations
Select the Template Mode > View In Template Mode option to view the template. Optionally apply a password to the template by right-clicking the device and selecting the Template Mode > Pass- word Protect Template option. M60 Motor Protection System GE Multilin...
Page 117 A serial number is viewable under Actual Values > Product Info > Model Information, the inside front panel, and the rear of the device. GE Multilin M60 Motor Protection System...
Page 118: Settings File Traceability
When a settings file is transfered to a M60 device, the date, time, and serial number of the M60 are sent back to EnerVista UR Setup and added to the settings file on the local PC. This infor- mation can be compared with the M60 actual values at any later date to determine if security has been compromised.
Page 119 With respect to the above diagram, the traceability feature is used as follows. The transfer date of a setting file written to a M60 is logged in the relay and can be viewed via EnerVista UR Setup or the front panel display. Likewise, the transfer date of a setting file saved to a local PC is logged in EnerVista UR Setup.
Page 120: Automatic Configurator
ONLINE DEVICE TRACEABILITY INFORMATION The M60 serial number and file transfer date are available for an online device through the actual values. Select the Actual Values > Product Info > Model Information menu item within the EnerVista UR Setup online window as shown in the example below.
Page 121: Faceplate Interface
LED panel 1 LED panel 2 LED panel 3 Display Front panel RS232 port Small user-programmable User-programmable Keypad (control) pushbuttons 1 to 7 pushbuttons 1 to 12 827801A7.CDR Figure 4–16: UR-SERIES STANDARD HORIZONTAL FACEPLATE PANELS GE Multilin M60 Motor Protection System 4-13...
Page 122: Led Indicators
The status indicators in the first column are described below. • IN SERVICE: This LED indicates that control power is applied, all monitored inputs, outputs, and internal systems are OK, and that the device has been programmed. 4-14 M60 Motor Protection System GE Multilin...
Page 123 Support for applying a customized label beside every LED is provided. Default labels are shipped in the label pack- age of every M60, together with custom templates. The default labels can be replaced by user-printed labels. User customization of LED operation is of maximum benefit in installations where languages other than English are used to communicate with operators.
Page 124 LEDs on these panels. USER-PROGRAMMABLE LEDS USER-PROGRAMMABLE LEDS 842782A1.CDR Figure 4–20: LED PANELS 2 AND 3 (INDEX TEMPLATE) DEFAULT LABELS FOR LED PANEL 2: The default labels are intended to represent: 4-16 M60 Motor Protection System GE Multilin...
Page 125: Custom Labeling Of Leds
EnerVista UR Setup software is installed and operational. • The M60 settings have been saved to a settings file. • The M60 front panel label cutout sheet (GE Multilin part number 1006-0047) has been downloaded from http://www.gegridsolutions.com/products/support/ur/URLEDenhanced.doc and printed. •...
Page 126 Enter the text to appear next to each LED and above each user-programmable pushbuttons in the fields provided. Feed the M60 front panel label cutout sheet into a printer and press the Print button in the front panel report window.
Page 127 4.3 FACEPLATE INTERFACE Bend the tab at the center of the tool tail as shown below. The following procedure describes how to remove the LED labels from the M60 enhanced front panel and insert the custom labels. Use the knife to lift the LED label and slide the label tool underneath. Make sure the bent tabs are pointing away from the relay.
Page 128 Slide the new LED label inside the pocket until the text is properly aligned with the LEDs, as shown below. The following procedure describes how to remove the user-programmable pushbutton labels from the M60 enhanced front panel and insert the custom labels.
Page 129 Slide the label tool under the user-programmable pushbutton label until the tabs snap out as shown below. This will attach the label tool to the user-programmable pushbutton label. Remove the tool and attached user-programmable pushbutton label as shown below. GE Multilin M60 Motor Protection System 4-21...
Page 130 The panel templates provide relative LED locations and located example text (x) edit boxes. The following procedure demonstrates how to install/uninstall the custom panel labeling. Remove the clear Lexan Front Cover (GE Multilin part number: 1501-0014). Push in...
Page 131: Display
4.3.6 BREAKER CONTROL a) INTRODUCTION The M60 can interface with associated circuit breakers. In many cases the application monitors the state of the breaker, which can be presented on faceplate LEDs, along with a breaker trouble indication. Breaker operations can be manually initiated from faceplate keypad or automatically initiated from a FlexLogic™...
Page 132: Menus
Each press of the MENU key advances through the following main heading pages: • Actual values. • Settings. • Commands. • Targets. • User displays (when enabled). 4-24 M60 Motor Protection System GE Multilin...
Page 133 Display Properties. TIME: 1.0 s  To view the remaining settings associated with the Display Properties subheader, DEFAULT MESSAGE repeatedly press the MESSAGE DOWN key. The last message appears as shown. INTENSITY: 25% GE Multilin M60 Motor Protection System 4-25...
Page 134: Changing Settings
ENTERING ALPHANUMERIC TEXT Text settings have data values which are fixed in length, but user-defined in character. They may be comprised of upper case letters, lower case letters, numerals, and a selection of special characters. 4-26 M60 Motor Protection System GE Multilin...
Page 135: Settings
When the "NEW SETTING HAS BEEN STORED" message appears, the relay will be in "Programmed" state and the In Service LED will turn on. e) ENTERING INITIAL PASSWORDS The M60 supports password entry from a local or remote connection. GE Multilin M60 Motor Protection System...
Page 136 When an incorrect command or setting password has been entered via the faceplate interface three times within a 3-minute time span, the FlexLogic™ operand will be set to “On” and the M60 will not allow settings or com- LOCAL ACCESS DENIED...
Page 137 FlexLogic™ operand will be set to “On” and REMOTE ACCESS DENIED the M60 will not allow Settings or Command access via the any external communications interface for the next ten minutes. FlexLogic™ operand will be set to “Off” after the expiration of the ten-minute timeout.
Page 138 4.3 FACEPLATE INTERFACE 4 HUMAN INTERFACES 4-30 M60 Motor Protection System GE Multilin...
Page 139: Overview
See page 5-65.   INSTALLATION See page 5-65.   SETTINGS  AC INPUTS See page 5-68.  SYSTEM SETUP   POWER SYSTEM See page 5-69.   SIGNAL SOURCES See page 5-70.  GE Multilin M60 Motor Protection System...
Page 140  OVERFREQUENCY See page 5-195.   START SUPERVISION See page 5-196.   REDUCED VOLTAGE See page 5-199.  STARTING  DIGITAL ELEMENTS See page 5-201.   DIGITAL COUNTERS See page 5-205.  M60 Motor Protection System GE Multilin...
Page 141  TRANSDUCER I/O   RTD INPUTS See page 5-236.   RRTD INPUTS See page 5-238.   DCMA OUTPUTS See page 5-242.   SETTINGS TEST MODE See page 5-246.  TESTING FUNCTION: Disabled GE Multilin M60 Motor Protection System...
Page 142: Introduction To Elements
“Disabled”. Once programmed to “Enabled”, any element associated with the function becomes active and all options become available. • NAME setting: This setting is used to uniquely identify the element. • SOURCE setting: This setting is used to select the parameter or set of parameters to be monitored. M60 Motor Protection System GE Multilin...
Page 143: Introduction To Ac Sources
BACKGROUND The M60 may be used on systems with breaker-and-a-half or ring bus configurations. In these applications, each of the two three-phase sets of individual phase currents (one associated with each breaker) can be used as an input to a breaker fail- ure element.
Page 144 INCREASING SLOT POSITION LETTER --> CT/VT MODULE 1 CT/VT MODULE 2 CT/VT MODULE 3 < bank 1 > < bank 3 > < bank 5 > < bank 2 > < bank 4 > < bank 6 > M60 Motor Protection System GE Multilin...
Page 145 CTs on each of two breakers is required to measure the winding current flow. GE Multilin M60 Motor Protection System...
Page 146: Product Setup
When entering a settings or command password via EnerVista or any serial interface, the user must enter the correspond- ing connection password. If the connection is to the back of the M60, the remote password must be used. If the connection is to the RS232 port of the faceplate, the local password must be used.
Page 147 The remote password settings are only visible from a remote connection via the EnerVista UR Setup software. Select the Settings > Product Setup > Password Security menu item to open the remote password settings window. Figure 5–2: REMOTE PASSWORD SETTINGS WINDOW GE Multilin M60 Motor Protection System...
Page 148 INVALID ATTEMPS BEFORE LOCKOUT The M60 provides a means to raise an alarm upon failed password entry. Should password verification fail while accessing a password-protected level of the relay (either settings or commands), the FlexLogic™ operand is UNAUTHORIZED ACCESS asserted.
Page 149 ACCESS AUTH TIMEOUT immediately denied. If access is permitted and an off-to-on transition of the FlexLogic™ operand is detected, the time- out is restarted. The status of this timer is updated every 5 seconds. GE Multilin M60 Motor Protection System 5-11...
Page 150: Display Properties
DEFAULT MESSAGE TIMEOUT: If the keypad is inactive for a period of time, the relay automatically reverts to a default message. The inactivity time is modified via this setting to ensure messages remain on the screen long enough during programming or reading of actual values. 5-12 M60 Motor Protection System GE Multilin...
Page 151 Some customers prefer very low currents to display as zero, while others prefer the current be displayed even when the value reflects noise rather than the actual signal. The M60 applies a cut- off value to the magnitudes and angles of the measured currents.
Page 152: Clear Relay Records
Selected records can be cleared from user-programmable conditions with FlexLogic™ operands. Assigning user-program- mable pushbuttons to clear specific records are typical applications for these commands. Since the M60 responds to rising edges of the configured FlexLogic™ operands, they must be asserted for at least 50 ms to take effect.
Page 153: Communications
SERIAL PORTS The M60 is equipped with up to three independent serial communication ports. The faceplate RS232 port is intended for local use and is fixed at 19200 baud and no parity. The rear COM1 port type is selected when ordering: either an Ethernet or RS485 port.
Page 154 If the RS485 COM2 port is used for an RRTD, then there must not be any other devices connected in the daisy-chain for any other purpose. The port is strictly dedicated to RRTD usage when is selected as “RRTD”. COM2 USAGE Power must be cycled to the M60 for changes to the setting to take effect. COM2 USAGE NOTE...
Page 155 MODBUS SLAVE ADDRESS grammed. For the RS485 ports each M60 must have a unique address from 1 to 254. Address 0 is the broadcast address which all Modbus slave devices listen to. Addresses do not have to be sequential, but no two devices can have the same address or conflicts resulting in errors will occur.
Page 156 DEADBAND: 30000 Range: 0 to 100000000 in steps of 1 DNP OTHER DEFAULT MESSAGE DEADBAND: 30000 Range: 1 to 10080 min. in steps of 1 DNP TIME SYNC IIN MESSAGE PERIOD: 1440 min 5-18 M60 Motor Protection System GE Multilin...
Page 157 TIMEOUT: 120 s The M60 supports the Distributed Network Protocol (DNP) version 3.0. The M60 can be used as a DNP slave device con- nected to multiple DNP masters (usually an RTU or a SCADA master station). Since the M60 maintains two sets of DNP data change buffers and connection information, two DNP masters can actively communicate with the M60 at one time.
Page 158 DNP analog input points that are voltages will be returned with values 1000 times smaller (for example, a value of 72000 V on the M60 will be returned as 72). These settings are useful when analog input values must be adjusted to fit within cer- tain ranges in DNP masters.
Page 159 0 to 32 binary output paired controls. Points not configured as paired oper- TROL POINTS ate on a one-to-one basis. setting is the DNP slave address. This number identifies the M60 on a DNP communications link. Each DNP ADDRESS DNP slave should be assigned a unique address.
Page 160 The M60 supports the Manufacturing Message Specification (MMS) protocol as specified by IEC 61850. MMS is supported over two protocol stacks: TCP/IP over ethernet and TP4/CLNP (OSI) over ethernet. The M60 operates as an IEC 61850 server. The Remote inputs and outputs section in this chapter describe the peer-to-peer GSSE/GOOSE message scheme.
Page 161 IEC 61850 GSSE application ID name string sent as part of each GSSE message. This GSSE ID string identifies the GSSE message to the receiving device. In M60 releases previous to 5.0x, this name string was repre- sented by the setting.
Page 162 DESTINATION MAC address; the least significant bit of the first byte must be set. In M60 releases previous to 5.0x, the destination Ethernet MAC address was determined automatically by taking the sending MAC address (that is, the unique, local MAC address of the M60) and setting the multicast bit.
Page 163 The M60 has the ability of detecting if a data item in one of the GOOSE datasets is erroneously oscillating. This can be caused by events such as errors in logic programming, inputs improperly being asserted and de-asserted, or failed station components.
Page 164 Configure the transmission dataset. Configure the GOOSE service settings. Configure the data. The general steps required for reception configuration are: Configure the reception dataset. Configure the GOOSE service settings. Configure the data. 5-26 M60 Motor Protection System GE Multilin...
Page 165 MMXU1 HZ DEADBAND change greater than 45 mHz, from the previous MMXU1.MX.mag.f value, in the source frequency. The M60 must be rebooted (control power removed and re-applied) before these settings take effect. The following procedure illustrates the reception configuration. Configure the reception dataset by making the following changes in the ...
Page 166 IEC61850 GOOSE ANALOG INPUT 1 UNITS The GOOSE analog input 1 can now be used as a FlexAnalog™ value in a FlexElement™ or in other settings. The M60 must be rebooted (control power removed and re-applied) before these settings take effect.
Page 167 CPU resources. When server scanning is disabled, there will be not updated to the IEC 61850 logical node sta- tus values in the M60. Clients will still be able to connect to the server (M60 relay), but most data values will not be updated.
Page 168 (_) character, and the first character in the prefix must be a letter. This conforms to the IEC 61850 standard. Changes to the logical node prefixes will not take effect until the M60 is restarted. The main menu for the IEC 61850 MMXU deadbands is shown below.
Page 169 The GGIO2 control configuration settings are used to set the control model for each input. The available choices are “0” (status only), “1” (direct control), and “2” (SBO with normal security). The GGIO2 control points are used to control the M60 virtual inputs.
Page 170 GGIO1 (binary status values). The settings allow the selection of FlexInteger™ values for each GGIO5 integer value point. It is intended that clients use GGIO5 to access generic integer values from the M60. Additional settings are provided to allow the selection of the number of integer values available in GGIO5 (1 to 16), and to assign FlexInteger™ values to the GGIO5 integer inputs.
Page 171 Changes to the report configuration take effect when the M60 is restarted. Disconnect any IEC 61850 client connection to the M60 prior to making setting changes to the report configuration. Disconnecting the rear Ethernet connection from the M60 disconnects the IEC 61850 client connection.
Page 172 NUMBER: The Trivial File Transfer Protocol (TFTP) can be used to transfer files from the M60 over a network. The M60 operates as a TFTP server. TFTP client software is available from various sources, including Microsoft Windows NT. The dir.txt file obtained from the M60 contains a list and description of all available files (event records, oscillography, etc.).
Page 173 The M60 supports the IEC 60870-5-104 protocol. The M60 can be used as an IEC 60870-5-104 slave device connected to a maximum of two masters (usually either an RTU or a SCADA master station). Since the M60 maintains two sets of IEC 60870-5-104 data change buffers, no more than two masters should actively communicate with the M60 at one time.
Page 174 M60 clock is closely synchronized with the SNTP/NTP server. It may take up to two minutes for the M60 to signal an SNTP self-test error if the server is offline.
Page 175 MESSAGE (Modbus register address range) Fast exchanges (50 to 1000 ms) are generally used in control schemes. The M60 has one fast exchange (Exchange 1) and two slow exchanges (Exchanges 2 and 3). The settings menu for the slow EGD exchanges is shown below: ...
Page 176: Modbus User Map
EXCH 1 DATA ITEM 1 to 20/50: These settings specify the data items that are part of this EGD exchange. Almost any data from the M60 memory map can be configured to be included in an EGD exchange. The settings are the starting Modbus register address for the data item in decimal format.
Page 177: Real Time Clock
SNTP, the offset is used to determine the local time for the M60 clock, since SNTP provides UTC time. The daylight savings time (DST) settings can be used to allow the M60 clock can follow the DST rules of the local time zone.
Page 178: User-Programmable Fault Report
The user programmable record contains the following information: the user-programmed relay name, detailed firmware revision (5.8x, for example) and relay model (M60), the date and time of trigger, the name of pre-fault trigger (a specific FlexLogic™ operand), the name of fault trigger (a specific FlexLogic™ operand), the active setting group at pre-fault trig- ger, the active setting group at fault trigger, pre-fault values of all programmed analog channels (one cycle before pre-fault trigger), and fault values of all programmed analog channels (at the fault trigger).
Page 179: Oscillography
Reducing the sampling rate allows longer records to be stored. This setting has no effect on the internal sampling rate of the relay which is always 64 samples per cycle; that is, it has no effect on the fundamental calculations of the device. GE Multilin M60 Motor Protection System 5-41...
Page 180 IB signal on terminal 2 of the CT/VT module in slot F. If there are no CT/VT modules and analog input modules, no analog traces will appear in the file; only the digital traces will appear. 5-42 M60 Motor Protection System GE Multilin...
Page 181: Data Logger
DATA LOGGER MODE: This setting configures the mode in which the data logger will operate. When set to “Continu- ous”, the data logger will actively record any configured channels at the rate as defined by the . The DATA LOGGER RATE GE Multilin M60 Motor Protection System 5-43...
Page 182: User-Programmable Leds
All 62 LEDs on the relay are illuminated. This is a quick test to verify if any of the LEDs is “burned”. This stage lasts as long as the control input is on, up to a maximum of 1 minute. After 1 minute, the test will end. 5-44 M60 Motor Protection System GE Multilin...
Page 183 Configure user-programmable pushbutton 1 by making the following entries in the  SETTINGS   menu: PRODUCT SETUP USER-PROGRAMMABLE PUSHBUTTONS USER PUSHBUTTON 1 “Self-reset” PUSHBUTTON 1 FUNCTION: “0.10 s” PUSHBTN 1 DROP-OUT TIME: GE Multilin M60 Motor Protection System 5-45...
Page 184 “Latched”, the LED, once lit, remains so until reset by the faceplate RESET button, from a remote device via a com- munications channel, or from any programmed operand, even if the LED operand state de-asserts. 5-46 M60 Motor Protection System GE Multilin...
Page 185: User-Programmable Self Tests
ANY SELF-TEST mode, minor alarms continue to function along with other major and minor alarms. Refer to the Relay self-tests section in chapter 7 for additional information on major and minor self-test alarms. GE Multilin M60 Motor Protection System 5-47...
Page 186: Control Pushbuttons
The location of the control pushbuttons are shown in the following figures. Control pushbuttons 842813A1.CDR Figure 5–4: CONTROL PUSHBUTTONS (ENHANCED FACEPLATE) An additional four control pushbuttons are included on the standard faceplate when the M60 is ordered with the twelve user-programmable pushbutton option. STATUS EVENT CAUSE...
Page 187: User-Programmable Pushbuttons
PUSHBTN 1 DROP-OUT MESSAGE TIME: 0.00 s Range: FlexLogic™ operand PUSHBTN 1 LED CTL: MESSAGE Range: Disabled, Normal, High Priority PUSHBTN 1 MESSAGE: MESSAGE Disabled Range: Disabled, Enabled PUSHBUTTON 1 MESSAGE EVENTS: Disabled GE Multilin M60 Motor Protection System 5-49...
Page 188 5.2 PRODUCT SETUP 5 SETTINGS The M60 is provided with this optional feature, specified as an option at the time of ordering. Using the order code for your device, see the order codes in chapter 2 for details. User-programmable pushbuttons provide an easy and error-free method of entering digital state (on, off) information. The number depends on the front panel ordered.
Page 189 This setting is applicable only if the user-programmable pushbutton is in "Latched" mode. • PUSHBTN 1 AUTORST: This setting enables the user-programmable pushbutton autoreset feature. This setting is applicable only if the pushbutton is in “Latched” mode. GE Multilin M60 Motor Protection System 5-51...
Page 190 To allow front panel keypad operation, when a keypad button is pressed the message is supressed for 10 seconds. • PUSHBUTTON 1 EVENTS: If this setting is enabled, each user-programmable pushbutton state change is logged as an event into the event recorder. 5-52 M60 Motor Protection System GE Multilin...
Page 191 5 SETTINGS 5.2 PRODUCT SETUP The figures show the user-programmable pushbutton logic. Figure 5–9: USER-PROGRAMMABLE PUSHBUTTON LOGIC (Sheet 1 of 2) GE Multilin M60 Motor Protection System 5-53...
Page 192: Flex State Parameters
16 states may be read out in a single Modbus register. The state bits can be configured so that all of the states which are of interest to the user are available in a minimum number of Modbus registers. 5-54 M60 Motor Protection System GE Multilin...
Page 193: User-Definable Displays
INVOKE AND SCROLL play, not at the first user-defined display. The pulses must last for at least 250 ms to take effect. INVOKE AND SCROLL GE Multilin M60 Motor Protection System 5-55...
Page 194 4 seconds. While viewing a user display, press the ENTER key and then select the ‘Yes” option to remove the display from the user display list. Use the MENU key again to exit the user displays menu. 5-56 M60 Motor Protection System GE Multilin...
Page 195 On type 7 cards that sup- port two channels, direct output messages are sent from both channels simultaneously. This effectively sends direct output GE Multilin M60 Motor Protection System 5-57...
Page 196 Delivery time for direct input and output messages is approximately 0.2 of a power system cycle at 128 kbps and 0.4 of a power system cycle at 64 kbps, per each ‘bridge’. 5-58 M60 Motor Protection System GE Multilin...
Page 197 The following application examples illustrate the basic concepts for direct input and output configuration. Please refer to the Inputs and outputs section in this chapter for information on configuring FlexLogic™ operands (flags, bits) to be exchanged. GE Multilin M60 Motor Protection System 5-59...
Page 198 UR IED 1 BLOCK UR IED 4 UR IED 2 UR IED 3 842712A1.CDR Figure 5–12: SAMPLE INTERLOCKING BUSBAR PROTECTION SCHEME For increased reliability, a dual-ring configuration (shown below) is recommended for this application. 5-60 M60 Motor Protection System GE Multilin...
Page 199 The complete application requires addressing a number of issues such as failure of both the communications rings, failure or out-of-service conditions of one of the relays, etc. Self-monitoring flags of the direct inputs and outputs feature would be primarily used to address these concerns. GE Multilin M60 Motor Protection System 5-61...
Page 200 Inputs and outputs section. A blocking pilot-aided scheme should be implemented with more security and, ideally, faster message delivery time. This could be accomplished using a dual-ring configuration as shown below. 5-62 M60 Motor Protection System GE Multilin...
Page 201 EVENTS: Disabled The M60 checks integrity of the incoming direct input and output messages using a 32-bit CRC. The CRC alarm function is available for monitoring the communication medium noise by tracking the rate of messages failing the CRC check. The monitoring function counts all incoming messages, including messages that failed the CRC check.
Page 202: Direct Inputs/Outputs
MESSAGE EVENTS: Disabled The M60 checks integrity of the direct input and output communication ring by counting unreturned messages. In the ring configuration, all messages originating at a given device should return within a pre-defined period of time. The unreturned messages alarm function is available for monitoring the integrity of the communication ring by tracking the rate of unre- turned messages.
Page 203: Teleprotection
TERMINAL 1 ID NUMBER 5.2.18 INSTALLATION   PATH: SETTINGS PRODUCT SETUP INSTALLATION Range: Not Programmed, Programmed  INSTALLATION RELAY SETTINGS:  Not Programmed Range: up to 20 alphanumeric characters RELAY NAME: MESSAGE Relay-1 GE Multilin M60 Motor Protection System 5-65...
Page 204 This name will appear on generated reports. This name RELAY NAME is also used to identify specific devices which are engaged in automatically sending/receiving data over the Ethernet com- munications channel using the IEC 61850 protocol. 5-66 M60 Motor Protection System GE Multilin...
Page 205: Remote Resources Configuration
Bricks. Remote resources settings configure the point-to-point connection between specific fiber optic ports on the M60 process card and specific Brick. The relay is then configured to measure spe- cific currents, voltages and contact inputs from those Bricks, and to control specific outputs.
Page 206: System Setup
1000:1 CT before summation. If a protection element is set up to act on SRC 1 currents, then a pickup level of 1 pu will operate on 1000 A primary. The same rule applies for current sums from CTs with different secondary taps (5 A and 1 A). 5-68 M60 Motor Protection System GE Multilin...
Page 207: Power System
GE Multilin M60 Motor Protection System 5-69...
Page 208: Signal Sources
FREQUENCY TRACKING cial variable-frequency applications. NOTE The frequency tracking feature will function only when the M60 is in the “Programmed” mode. If the M60 is “Not Programmed”, then metering values will be available but may exhibit significant errors. NOTE 5.4.3 SIGNAL SOURCES ...
Page 209 CT/VT inputs that are used to provide the data. DSP Bank Source 1 Source 2 Amps Amps Source 3 51BF-1 51BF-2 Volts Amps Amps Volts Source 4 UR Relay Figure 5–18: EXAMPLE USE OF SOURCES GE Multilin M60 Motor Protection System 5-71...
Page 210 MOTOR OVERLOAD FACTOR: This setting defines the current level at which the motor is considered to be over- loaded. If the motor current exceeds the threshold, the M60 thermal model reacts by accu- MOTOR OVERLOAD FACTOR mulating thermal capacity. Normally, this factor is set slightly above the motor service factor to account for inherent load measuring errors (CTs and limited relay accuracy).
Page 211 M60 to determine which settings should be active at any given time. To maintain correct motor status indication, the M60 expects a transition from speed 1 to speed 2 within two seconds; otherwise, the motor status value may be reset.
Page 212: Motor
SPEED2 MOTOR FLA: This setting specifies the motor full load current for speed 2. MOTOR CT bank 1 CT bank 2 STOP M60 protection and logic HIGH 833723A1.CDR Figure 5–19: TWO SPEED MOTOR CONNECTIONS 5-74 M60 Motor Protection System GE Multilin...
Page 213: Breakers
Range: 0.000 to 1 000 000.000 s in steps of 0.001 MANUAL CLOSE RECAL1 MESSAGE TIME: 0.000 s Range: FlexLogic™ operand BREAKER 1 OUT OF SV: MESSAGE Range: Disabled, Enabled BREAKER 1 EVENTS: MESSAGE Disabled GE Multilin M60 Motor Protection System 5-75...
Page 214 1. The number of breaker control elements is dependent on the number of CT/VT modules specified with the M60. The follow- ing settings are available for each breaker control element.
Page 215 5 SETTINGS 5.4 SYSTEM SETUP Figure 5–20: DUAL BREAKER CONTROL SCHEME LOGIC (Sheet 1 of 2) IEC 61850 functionality is permitted when the M60 is in “Programmed” mode and not in the local control mode. NOTE GE Multilin M60 Motor Protection System...
Page 216 FLEXLOGIC OPERANDS BREAKER 1 ANY P OPEN BREAKER 1 1P OPEN BREAKER 1 OOS SETTING BREAKER 1 OUT OF SV = Off 842025A1.CDR Figure 5–21: DUAL BREAKER CONTROL SCHEME LOGIC (Sheet 2 of 2) 5-78 M60 Motor Protection System GE Multilin...
Page 217: Disconnect Switches
1. • SWITCH 1 MODE: This setting selects “3-pole” mode, where all disconnect switch poles are operated simultaneously, or “1-pole” mode where all disconnect switch poles are operated either independently or simultaneously. GE Multilin M60 Motor Protection System 5-79...
Page 218 SWITCH 1 ALARM DELAY: This setting specifies the delay interval during which a disagreement of status among the three-pole position tracking operands will not declare a pole disagreement. This allows for non-simultaneous operation of the poles. IEC 61850 functionality is permitted when the M60 is in “Programmed” mode and not in the local control mode. NOTE 5-80...
Page 219 5 SETTINGS 5.4 SYSTEM SETUP Figure 5–22: DISCONNECT SWITCH SCHEME LOGIC GE Multilin M60 Motor Protection System 5-81...
Page 220: Flexcurves
1.03 pu. It is recommended to set the two times to a similar value; otherwise, the linear approximation may result in undesired behavior for the operating quantity that is close to 1.00 pu. 5-82 M60 Motor Protection System GE Multilin...
Page 221 The multiplier and adder settings only affect the curve portion of the characteristic and not the MRT and HCT set- tings. The HCT settings override the MRT settings for multiples of pickup greater than the HCT ratio. NOTE GE Multilin M60 Motor Protection System 5-83...
Page 222 EnerVista UR Setup software generates an error message and discards the proposed changes. NOTE e) STANDARD RECLOSER CURVES The standard recloser curves available for the M60 are displayed in the following graphs. 5-84 M60 Motor Protection System...
Page 223 CURRENT (multiple of pickup) 842723A1.CDR Figure 5–26: RECLOSER CURVES GE101 TO GE106 GE142 GE138 GE120 GE113 0.05 7 8 9 10 12 CURRENT (multiple of pickup) 842725A1.CDR Figure 5–27: RECLOSER CURVES GE113, GE120, GE138 AND GE142 GE Multilin M60 Motor Protection System 5-85...
Page 224 Figure 5–28: RECLOSER CURVES GE134, GE137, GE140, GE151 AND GE201 GE152 GE141 GE131 GE200 7 8 9 10 12 CURRENT (multiple of pickup) 842728A1.CDR Figure 5–29: RECLOSER CURVES GE131, GE141, GE152, AND GE200 5-86 M60 Motor Protection System GE Multilin...
Page 225 Figure 5–30: RECLOSER CURVES GE133, GE161, GE162, GE163, GE164 AND GE165 GE132 GE139 GE136 GE116 0.05 GE117 GE118 0.02 0.01 7 8 9 10 12 CURRENT (multiple of pickup) 842726A1.CDR Figure 5–31: RECLOSER CURVES GE116, GE117, GE118, GE132, GE136, AND GE139 GE Multilin M60 Motor Protection System 5-87...
Page 226 Figure 5–32: RECLOSER CURVES GE107, GE111, GE112, GE114, GE115, GE121, AND GE122 GE202 GE135 GE119 7 8 9 10 12 CURRENT (multiple of pickup) 842727A1.CDR Figure 5–33: RECLOSER CURVES GE119, GE135, AND GE202 5-88 M60 Motor Protection System GE Multilin...
Page 227: Flexlogic
Figure 5–34: UR ARCHITECTURE OVERVIEW The states of all digital signals used in the M60 are represented by flags (or FlexLogic™ operands, which are described later in this section). A digital “1” is represented by a 'set' flag. Any external contact change-of-state can be used to block an element from operating, as an input to a control feature in a FlexLogic™...
Page 228 Some types of operands are present in the relay in multiple instances; e.g. contact and remote inputs. These types of oper- ands are grouped together (for presentation purposes only) on the faceplate display. The characteristics of the different types of operands are listed in the table below. Table 5–8: M60 FLEXLOGIC™ OPERAND TYPES OPERAND TYPE STATE...
Page 229 5 SETTINGS 5.5 FLEXLOGIC™ The operands available for this relay are listed alphabetically by types in the following table. Table 5–9: M60 FLEXLOGIC™ OPERANDS (Sheet 1 of 8) OPERAND TYPE OPERAND SYNTAX OPERAND DESCRIPTION CONTROL CONTROL PUSHBTN 1 ON Control pushbutton 1 is being pressed...
Page 230 5.5 FLEXLOGIC™ 5 SETTINGS Table 5–9: M60 FLEXLOGIC™ OPERANDS (Sheet 2 of 8) OPERAND TYPE OPERAND SYNTAX OPERAND DESCRIPTION ELEMENT: BREAKER 1 OFF CMD Breaker 1 open command initiated Breaker control BREAKER 1 ON CMD Breaker 1 close command initiated BREAKER 1 ΦA BAD ST...
Page 231 5 SETTINGS 5.5 FLEXLOGIC™ Table 5–9: M60 FLEXLOGIC™ OPERANDS (Sheet 3 of 8) OPERAND TYPE OPERAND SYNTAX OPERAND DESCRIPTION ELEMENT: MECHANICAL JAM PKP The mechanical jam element has picked up Motor mechanical MECHANICAL JAM DPO The mechanical jam element has dropped out...
Page 232 5.5 FLEXLOGIC™ 5 SETTINGS Table 5–9: M60 FLEXLOGIC™ OPERANDS (Sheet 4 of 8) OPERAND TYPE OPERAND SYNTAX OPERAND DESCRIPTION ELEMENT: PHASE UV1 PKP At least one phase of phase undervoltage 1 has picked up Phase undervoltage PHASE UV1 OP At least one phase of phase undervoltage 1 has operated...
Page 233 5 SETTINGS 5.5 FLEXLOGIC™ Table 5–9: M60 FLEXLOGIC™ OPERANDS (Sheet 5 of 8) OPERAND TYPE OPERAND SYNTAX OPERAND DESCRIPTION ELEMENT: SH STAT GND STG1 PKP Stage 1 of the sub-harmonic stator ground protection has picked up Sub-harmonic stator SH STAT GND STG1 DPO...
Page 234 5.5 FLEXLOGIC™ 5 SETTINGS Table 5–9: M60 FLEXLOGIC™ OPERANDS (Sheet 6 of 8) OPERAND TYPE OPERAND SYNTAX OPERAND DESCRIPTION ELEMENT: TELEPRO INPUT 1-1 On Flag is set, Logic =1 ↓ ↓ Teleprotection inputs/outputs TELEPRO INPUT 1-16 On Flag is set, Logic =1...
Page 235 5 SETTINGS 5.5 FLEXLOGIC™ Table 5–9: M60 FLEXLOGIC™ OPERANDS (Sheet 7 of 8) OPERAND TYPE OPERAND SYNTAX OPERAND DESCRIPTION INPUTS/OUTPUTS: REMOTE INPUT 1 On Flag is set, logic=1 ↓ ↓ Remote inputs REMOTE INPUT 32 On Flag is set, logic=1...
Page 236 5.5 FLEXLOGIC™ 5 SETTINGS Table 5–9: M60 FLEXLOGIC™ OPERANDS (Sheet 8 of 8) OPERAND TYPE OPERAND SYNTAX OPERAND DESCRIPTION SELF- ANY MAJOR ERROR Any of the major self-test errors generated (major error) DIAGNOSTICS ANY MINOR ERROR Any of the minor self-test errors generated (minor error)
Page 237: Flexlogic™ Rules
When making changes to settings, all FlexLogic™ equations are re-compiled whenever any new setting value is entered, so all latches are automatically reset. If it is necessary to re-initialize FlexLogic™ during testing, for exam- ple, it is suggested to power the unit down and then back up. GE Multilin M60 Motor Protection System 5-99...
Page 238: Flexlogic™ Example
DIGITAL ELEMENT 1 on Dropout State=Pickup (200 ms) DIGITAL ELEMENT 2 Timer 1 State=Operated Time Delay on Pickup (800 ms) CONTACT INPUT H1c State=Closed VIRTUAL OUTPUT 3 827026A2.VSD Figure 5–36: LOGIC EXAMPLE WITH VIRTUAL OUTPUTS 5-100 M60 Motor Protection System GE Multilin...
Page 239 Following the procedure outlined, start with parameter 99, as follows: 99: The final output of the equation is virtual output 3, which is created by the operator "= Virt Op n". This parameter is therefore "= Virt Op 3." GE Multilin M60 Motor Protection System 5-101...
Page 240 87: The input just below the upper input to OR #1 is operand “Virt Op 2 On". 86: The upper input to OR #1 is operand “Virt Op 1 On". 85: The last parameter is used to set the latch, and is operand “Virt Op 4 On". 5-102 M60 Motor Protection System GE Multilin...
Page 241 In the following equation, virtual output 3 is used as an input to both latch 1 and timer 1 as arranged in the order shown below: DIG ELEM 2 OP Cont Ip H1c On AND(2) GE Multilin M60 Motor Protection System 5-103...
Page 242: Flexlogic™ Equation Editor
TIMER 1 TYPE: This setting is used to select the time measuring unit. • TIMER 1 PICKUP DELAY: Sets the time delay to pickup. If a pickup delay is not required, set this function to "0". 5-104 M60 Motor Protection System GE Multilin...
Page 243: Flexelements
The element can be programmed to respond either to a signal level or to a rate-of-change (delta) over a pre-defined period of time. The output operand is asserted when the operating signal is higher than a threshold or lower than a threshold as per user's choice. GE Multilin M60 Motor Protection System 5-105...
Page 244 The FLEXELEMENT 1 DIRECTION following figure explains the application of the FLEXELEMENT 1 DIRECTION FLEXELEMENT 1 PICKUP FLEXELEMENT 1 HYS- settings. TERESIS 5-106 M60 Motor Protection System GE Multilin...
Page 245 DIRECTION = Under; FLEXELEMENT INPUT MODE = Signed; FlexElement 1 OpSig FLEXELEMENT 1 PKP FLEXELEMENT DIRECTION = Under; FLEXELEMENT INPUT MODE = Absolute; FlexElement 1 OpSig 842706A2.CDR Figure 5–44: FLEXELEMENT™ INPUT MODE SETTING GE Multilin M60 Motor Protection System 5-107...
Page 246 “Delta”. FLEXELEMENT 1 COMP MODE This setting specifies the pickup delay of the element. The setting FLEXELEMENT 1 PKP DELAY FLEXELEMENT 1 RST DELAY specifies the reset delay of the element. 5-108 M60 Motor Protection System GE Multilin...
Page 247: Non-Volatile Latches
LATCH N LATCH N LATCH N LATCH N TYPE RESET Reset Dominant Previous Previous State State Dominant Previous Previous State State Figure 5–45: NON-VOLATILE LATCH OPERATION TABLE (N = 1 to 16) AND LOGIC GE Multilin M60 Motor Protection System 5-109...
Page 248: Grouped Elements
Each of the six setting group menus is identical. Setting group 1 (the default active group) automatically becomes active if no other group is active (see the Control elements section for additional details). 5-110 M60 Motor Protection System GE Multilin...
Page 249 The figure below shows examples of constant and variable acceleration currents and explains measurement of the acceler- ation time and current. Part A represents a constant current start and part B represents a variable current start. GE Multilin M60 Motor Protection System 5-111...
Page 250 Peak acceleration current ACCELERATION TIME = Ib magnitude Effective acceleration current EFFECTIVE CURENT Acceleration time = Ic magnitude PEAK CURRENT FLEXLOGIC OPERANDS MOTOR STARTING MOTOR RUNNING 833013A3.CDR Figure 5–47: ACCELERATION TIME SCHEME LOGIC 5-112 M60 Motor Protection System GE Multilin...
Page 251 Range: 1.50 to 20.00 x FLA in steps of 0.01 VD ACCELL. INTERSECT MESSAGE @ MIN V: 4.00 x FLA Range: 1.50 to 20.00 x FLA in steps of 0.01 VD STALL CURRENT @ MESSAGE 100% V: 6.00 x FLA GE Multilin M60 Motor Protection System 5-113...
Page 252 Once the motor load current exceeds the overload level (FLA x overload factor), it enters an overload phase; that is, the heat accumulation becomes greater than the heat dissipation. The M60 thermal model reacts by incrementing the thermal capacity used (TCU) at a rate dependent on the selected thermal curve and overload level. When the thermal capacity reaches 100%, the operand (typically configured to trip the motor) is set.
Page 253 20.82 If “IEC” is selected as the thermal model curve, the M60 can apply the IEC 255-8 hot and cold curve characteristics to the thermal model. The M60 will evaluate the thermal capacity at motor start and choose the appropriate curve. The hot curve characteristic is applied when the thermal capacity is greater than or equal to 5% (that is, a point above where the motor is not at complete rest, or cold).
Page 254 IEC CURVE k FACTOR: This setting applies only to the IEC motor curve and is applied as described in the THERMAL setting description. Refer to the IEC 255-8 standard for additional details on its application. MODEL CURVE 5-116 M60 Motor Protection System GE Multilin...
Page 255 Multiples of Pickup ( Pickup = OF x FLA) Figure 5–49: STANDARD MOTOR CURVES During the interval of discontinuity, the longer of the two trip times is used to reduce the chance of nuisance tripping during motor starts. NOTE GE Multilin M60 Motor Protection System 5-117...
Page 256 0.56 2800 28000 833004A2.CDR Figure 5–50: FLEXCURVE™ EXAMPLE The FlexCurve™ programming is based on per-unit current values. The equivalent primary amperes and mul- tiplier of full load current are also indicated above. NOTE 5-118 M60 Motor Protection System GE Multilin...
Page 257 Motor cooling is calculated as follows: t τ ⁄ – (EQ 5.14) – start   1   ------------------------------------------ - ---------- - × 100% (EQ 5.15) –     overload_pickup cold GE Multilin M60 Motor Protection System 5-119...
Page 258 (average three phase RMS and the selected setting. Thermal capacity used will either rise at the fixed rate of 5% per minute or fall as dictated by the running cool time constant.   × ---------- - × 100% (EQ 5.16) –   cold 5-120 M60 Motor Protection System GE Multilin...
Page 259 100%, the load current must be above the overload pickup setting to set the output. Do not program setpoint greater than 200°C if using a remote RTD unit, since the RRTD RTD BIAS MAXIMUM only measures temperatures up to 200°C. NOTE GE Multilin M60 Motor Protection System 5-121...
Page 260 TCU values are to be applied: TC accumulated from the moment the motor was stopped start (EQ 5.23)     margin 100% × ------------------------- - –     maxStart 100% 5-122 M60 Motor Protection System GE Multilin...
Page 261 MULTIPLES OF FULL LOAD AMPS 806821A4.CDR Voltage dependent overload functionality is operational only if the selected (see the MOTOR LINE SOURCE SYS-  menu) is assigned to a valid three-phase VT. MOTOR SETUP NOTE GE Multilin M60 Motor Protection System 5-123...
Page 262 ). This value can be typically determined from motor acceleration curves. The value at the breakdown torque for the minimum volt- age start is recommended for this setting. 833714A1.CDR Figure 5–54: TYPICAL MOTOR ACCELERATION CHARACTERISTICS 5-124 M60 Motor Protection System GE Multilin...
Page 263 1.00 PER UNIT CURRENT THERMAL MODEL CURVE LOCKED ROTOR LINE MIN V ACCELERATE 100% ACCELERATE 110% ACCELERATE MIN V LINE 100% V LINE 110% V LINE 833715A1.CDR Figure 5–55: VOLTAGE DEPENDENT OVERLOAD CURVES GE Multilin M60 Motor Protection System 5-125...
Page 264 The following three figures illustrate the resultant overload protection curve for minimum, 100%, and maximum line voltages. For voltages between these limits, the M60 will shift the acceleration curve linearly and constantly, based on the measured line voltage during a motor start.
Page 265 PER UNIT CURRENT 833716A1.CDR Figure 5–56: VOLTAGE DEPENDENT OVERLOAD CURVE PROTECTION AT MINIMUM VOLTAGE 10000.00 1000.00 100.00 10.00 1.00 PER UNIT CURRENT 833717A1.CDR Figure 5–57: VOLTAGE DEPENDENT OVERLOAD CURVE PROTECTION AT 100% VOLTAGE GE Multilin M60 Motor Protection System 5-127...
Page 266 The following three figures illustrate the motor starting curves for the following abnormal conditions: line voltages below the minimum, above 110%, and the situation for voltage loss. 10000.00 1000.00 100.00 10.00 1.00 PER UNIT CURRENT 833719A1.CDR Figure 5–59: VOLTAGE DEPENDENT OVERLOAD CURVE PROTECTION AT LESS THAN MINIMUM VOLTAGE 5-128 M60 Motor Protection System GE Multilin...
Page 267 833720A1.CDR Figure 5–60: VOLTAGE DEPENDENT OVERLOAD CURVE PROTECTION AT VOLTAGE LOSS CONDITION 10000.00 1000.00 100.00 10.00 1.00 PER UNIT CURRENT 833721A1.CDR Figure 5–61: VOLTAGE DEPENDENT OVERLOAD CURVE PROTECTION AT MORE THAN 110% VOLTAGE GE Multilin M60 Motor Protection System 5-129...
Page 268 5.6 GROUPED ELEMENTS 5 SETTINGS For the three abnormal voltage situations, the M60 makes a transition from the acceleration curve to Motor or Flex- Curve when the operands are asserted. MOTOR RUNNING MOTOR OVERLOADED NOTE SETTING Voltage Dependent Function Disabled = 0...
Page 269 5 SETTINGS 5.6 GROUPED ELEMENTS Figure 5–63: THERMAL MODEL LOGIC GE Multilin M60 Motor Protection System 5-131...
Page 270: Motor
3 to 10 seconds. • AMP UNBAL 1(2) RESET DELAY: This timer can be used to maintain the output until other equipment or an operator can react to the unbalance condition. 5-132 M60 Motor Protection System GE Multilin...
Page 271 SYSTEM SETUP MOTOR MOTOR LINE SOURCE motor status asserted by the thermal model element. Both the signal source and thermal protection must be configured properly in order for the mechanical jam protection to operate. GE Multilin M60 Motor Protection System 5-133...
Page 272   setting. SYSTEM SETUP MOTOR MOTOR LINE SOURCE Phase currents must be configured on this source; otherwise, the undercurrent function will not be operational. The ele- ment responds to a per-phase current. 5-134 M60 Motor Protection System GE Multilin...
Page 273 FLEXLOGIC OPERANDS magnitude Ia < PICKUP MOTOR LINE SOURCE U/CURR ALARM PKP = Ia magnitude Ib < PICKUP U/CURR TRIP PKP = Ib magnitude IC < PICKUP = Ic 833024A1.CDR Figure 5–66: UNDERCURRENT LOGIC GE Multilin M60 Motor Protection System 5-135...
Page 274 When two-speed motor functionality is used, these settings allow the selection of proper parameters for the thermal model when motor is switched to the second speed. There is one thermal model in the M60, and it has inputs for overload condi- tions from calculations at both speeds.
Page 275 The acceleration time at speed 2 becomes functional only if the acceleration time at speed 1 is enabled. When the acceleration time at any speed is not required, it can be per- manently blocked. GE Multilin M60 Motor Protection System 5-137...
Page 276 2. Prior to starting, the motor state is determined from the operand. Refer to MOTOR OFFLINE the Motor setup section for additional information on the motor offline state determination. The speed 2 undercurrent 5-138 M60 Motor Protection System GE Multilin...
Page 277 IA_mag < PICKUP = Ia magnitude U/CURR SP2 ALARM PKP = Ib magnitude IB_mag < PICKUP U/CURR SP2 TRIP PKP IC_mag < PICKUP = Ic magnitude 833022A1.CDR Figure 5–69: SPEED 2 UNDERCURRENT LOGIC GE Multilin M60 Motor Protection System 5-139...
Page 278: Stator Differential
This element has a dual slope characteristic. The main purpose of the percent-slope characteristic is to prevent a maloper- ation caused by unbalances between CTs during external faults. CT unbalances arise as a result of the following factors: CT accuracy errors 5-140 M60 Motor Protection System GE Multilin...
Page 279 STATOR DIFF PKP B D.F.T. SETTING STATOR DIFF DPO B STATOR DIFF Differential NEUTRAL END SOURCE: and Restraint Restraint Phasors FLEXLOGIC OPERANDS STATOR DIFF PKP C STATOR DIFF DPO C Figure 5–71: STATOR DIFFERENTIAL SCHEME LOGIC GE Multilin M60 Motor Protection System 5-141...
Page 280 In order to provide additional security against maloperations during these events, the M60 incorporates saturation detection logic. When saturation is detected the element will make an additional check on the angle between the neutral and output current.
Page 281: Power
5.6.5 POWER a) MAIN MENU    PATH: SETTINGS GROUPED ELEMENTS SETTING GROUP 1(6) POWER  POWER  SENSITIVE See page 5-144.   DIRECTIONAL POWER  UNDERPOWER MESSAGE See page 5-147.  GE Multilin M60 Motor Protection System 5-143...
Page 282 The operating quantity is displayed in the   actual ACTUAL VALUES METERING SENSITIVE DIRECTIONAL POWER 1(2) value. The element has two independent (as to the pickup and delay settings) stages for alarm and trip, respectively. 5-144 M60 Motor Protection System GE Multilin...
Page 283 RCA = 0 SMIN < 0 SMIN > 0 OPERATE RESTRAIN RESTRAIN OPERATE RCA = 90 RCA = 270 SMIN > 0 SMIN < 0 842702A1.CDR Figure 5–75: DIRECTIONAL POWER ELEMENT SAMPLE APPLICATIONS GE Multilin M60 Motor Protection System 5-145...
Page 284 DIR POWER 1 OP Three-phase reactive power (Q) DIR POWER 1 STG2 DPO DIR POWER 1 STG2 OP SETTING DIR POWER 1 STG2 DELAY: 100 ms 842003A3.CDR Figure 5–76: SENSITIVE DIRECTIONAL POWER SCHEME LOGIC 5-146 M60 Motor Protection System GE Multilin...
Page 285 3 × VT pu base × CT pu base per source selected as a motor line source. This setting should be less than the corresponding setting for the alarm stage. GE Multilin M60 Motor Protection System 5-147...
Page 286 Vb > 0.25 pu UNDERPOWER 1 magnitude Vc > 0.25 pu FUNCTION = Enabled UNDERPOWER 1 BLOCK = Off SETTING UNDERPOWER 1 START BLOCK DLY FLEXLOGIC OPERAND MOTOR OFFLINE 833025A1.CDR Figure 5–77: UNDERPOWER LOGIC 5-148 M60 Motor Protection System GE Multilin...
Page 287: Phase Current
 PHASE MESSAGE See page 5-152.  DIRECTIONAL 2 The M60 Motor Protection System has up to eight (8) phase instantaneous overcurrent elements (dependent on CT/VT modules ordered) and two (2) phase directional overcurrent elements. GE Multilin M60 Motor Protection System...
Page 288 The phase instantaneous overcurrent element may be used as an instantaneous element with no intentional delay or as a definite time element. The input current is the fundamental phasor magnitude. The phase instantaneous overcurrent timing curves are shown below for form-A contacts in a 60 Hz system. 5-150 M60 Motor Protection System GE Multilin...
Page 289 5 SETTINGS 5.6 GROUPED ELEMENTS Figure 5–78: PHASE INSTANTANEOUS OVERCURRENT TIMING CURVES Figure 5–79: PHASE INSTANTANEOUS OVERCURRENT 1 SCHEME LOGIC GE Multilin M60 Motor Protection System 5-151...
Page 290 30° +90° Phasors for Phase A Polarization: × VPol = VBC (1/_ECA) = polarizing voltage IA = operating current ECA = Element Characteristic Angle at 30° 827800A2.CDR Figure 5–80: PHASE A DIRECTIONAL POLARIZATION 5-152 M60 Motor Protection System GE Multilin...
Page 291 When set to "Yes", the directional element blocks the operation of any phase overcurrent element under directional control, when voltage memory expires; when set to "No", the directional element allows tripping of phase overcurrent elements under directional control. GE Multilin M60 Motor Protection System 5-153...
Page 292 FLEXLOGIC OPERAND PHASE B LOGIC SIMILAR TO PHASE A PH DIR1 BLK B FLEXLOGIC OPERAND PHASE C LOGIC SIMILAR TO PHASE A PH DIR1 BLK C 827078A6.CDR Figure 5–81: PHASE DIRECTIONAL SCHEME LOGIC 5-154 M60 Motor Protection System GE Multilin...
Page 293: Neutral Current
MESSAGE See page 5-156.  DIRECTIONAL 2 The M60 Motor Protection System has up to eight (8) neutral instantaneous overcurrent elements (dependent on CT/VT modules ordered) and two (2) neutral directional overcurrent elements. b) NEUTRAL INSTANTANEOUS OVERCURRENT (ANSI 50N) ...
Page 294 Range: 40 to 90° in steps of 1 NEUTRAL DIR OC1 REV MESSAGE LIMIT ANGLE: 90° Range: 0.006 to 30.000 pu in steps of 0.001 NEUTRAL DIR OC1 REV MESSAGE PICKUP: 0.050 pu 5-156 M60 Motor Protection System GE Multilin...
Page 295 | > 0.8 pu –V_0 + Z_offset × I_0 I_0 × 1∠ECA = 3 × (|I_0|) if |I | ≤ 0.8 pu Forward Dual –V_0 + Z_offset × I_0 –I_0 × 1∠ECA Reverse –I_0 GE Multilin M60 Motor Protection System 5-157...
Page 296 If “Voltage” polarizing is selected, the element uses the zero-sequence voltage angle for polarization. The user can use either the zero-sequence voltage V_0 calculated from the phase voltages, or the zero-sequence voltage supplied externally as the auxiliary voltage V_X, both from the NEUTRAL DIR OC1 SOURCE 5-158 M60 Motor Protection System GE Multilin...
Page 297 “Calculated 3I0” mode of operation. • NEUTRAL DIR OC1 REV LIMIT ANGLE: This setting defines a symmetrical (in both directions from the ECA) limit angle for the reverse direction. GE Multilin M60 Motor Protection System 5-159...
Page 298: Ground Current
 GROUND CURRENT  GROUND TOC1 See page 5-166.    GROUND TOC2 MESSAGE See page 5-166.   GROUND IOC1 MESSAGE See page 5-167.   GROUND IOC2 MESSAGE See page 5-167.  5-160 M60 Motor Protection System GE Multilin...
Page 299 5.6 GROUPED ELEMENTS b) INVERSE TOC CURVE CHARACTERISTICS The inverse time overcurrent curves used by the time overcurrent elements are the IEEE, IEC, GE Type IAC, and I t stan- dard curve shapes. This allows for simplified coordination with downstream devices.
Page 300 5.041 4.827 38.634 22.819 14.593 11.675 10.130 9.153 8.470 7.960 7.562 7.241 51.512 30.426 19.458 15.567 13.507 12.204 11.294 10.614 10.083 9.654 10.0 64.390 38.032 24.322 19.458 16.883 15.255 14.117 13.267 12.604 12.068 5-162 M60 Motor Protection System GE Multilin...
Page 301 0.60 1.835 1.067 0.668 0.526 0.451 0.404 0.371 0.346 0.327 0.311 0.80 2.446 1.423 0.890 0.702 0.602 0.538 0.494 0.461 0.435 0.415 1.00 3.058 1.778 1.113 0.877 0.752 0.673 0.618 0.576 0.544 0.518 GE Multilin M60 Motor Protection System 5-163...
Page 302 = characteristic constant, and T = reset time in seconds (assuming energy capacity is 100% RESET is “Timed”) RESET Table 5–20: GE TYPE IAC INVERSE TIME CURVE CONSTANTS IAC CURVE SHAPE IAC Extreme Inverse 0.0040 0.6379 0.6200 1.7872 0.2461...
Page 303 = Reset Time in seconds (assuming energy capacity is 100% and RESET: Timed) RESET RECLOSER CURVES: The M60 uses the FlexCurve™ feature to facilitate programming of 41 recloser curves. Please refer to the FlexCurve™ section in this chapter for additional details. GE Multilin...
Page 304 GROUND TOC 1 SETTING GROUND TOC1 PKP RESET: GROUND TOC1 GROUND TOC1 DPO IG ≥ PICKUP SOURCE: GROUND TOC1 OP SETTING GROUND TOC1 BLOCK: Off = 0 827036A3.VSD Figure 5–85: GROUND TOC1 SCHEME LOGIC 5-166 M60 Motor Protection System GE Multilin...
Page 305 Enabled = 1 SETTING DELAY: GROUND IOC1 GROUND IOC1 RESET SETTING PICKUP: DELAY: GROUND IOC1 SOURCE: IG ≥ PICKUP SETTING GROUND IOC1 BLOCK: 827037A4.VSD Off = 0 Figure 5–86: GROUND IOC1 SCHEME LOGIC GE Multilin M60 Motor Protection System 5-167...
Page 306: Breaker Failure
Range: 0.001 to 30.000 pu in steps of 0.001 BF1 N AMP HISET MESSAGE PICKUP: 1.050 pu Range: 0.001 to 30.000 pu in steps of 0.001 BF1 PH AMP LOSET MESSAGE PICKUP: 1.050 pu 5-168 M60 Motor Protection System GE Multilin...
Page 307 This can also occur in breaker-and-a-half or ring bus configurations where the first breaker closes into a fault; the protection trips and attempts to initiate breaker failure for the second breaker, which is in the process of closing, but does not yet have current flowing through it. GE Multilin M60 Motor Protection System 5-169...
Page 308 BREAKER FAILURE TIMER No. 2 (±1/8 cycle) INITIATE (1/8 cycle) BREAKER FAILURE CURRENT DETECTOR PICKUP (1/8 cycle) BREAKER FAILURE OUTPUT RELAY PICKUP (1/4 cycle) FAULT cycles OCCURS 827083A6.CDR Figure 5–87: BREAKER FAILURE MAIN PATH SEQUENCE 5-170 M60 Motor Protection System GE Multilin...
Page 309 In microprocessor relays this time is not significant. In M60 relays, which use a Fourier transform, the calculated current magnitude will ramp-down to zero one power frequency cycle after the current is interrupted, and this lag should be included in the overall margin duration, as it occurs after current interruption.
Page 310 Upon operation of the breaker failure element for a single pole trip command, a three-pole trip command should be given via output operand BKR FAIL 1 TRIP OP 5-172 M60 Motor Protection System GE Multilin...
Page 311 5 SETTINGS 5.6 GROUPED ELEMENTS Figure 5–89: SINGLE-POLE BREAKER FAILURE, INITIATE (Sheet 1 of 2) GE Multilin M60 Motor Protection System 5-173...
Page 312 5.6 GROUPED ELEMENTS 5 SETTINGS Figure 5–90: SINGLE-POLE BREAKER FAILURE, TIMERS (Sheet 2 of 2) 5-174 M60 Motor Protection System GE Multilin...
Page 313 5 SETTINGS 5.6 GROUPED ELEMENTS Figure 5–91: THREE-POLE BREAKER FAILURE, INITIATE (Sheet 1 of 2) GE Multilin M60 Motor Protection System 5-175...
Page 314 5.6 GROUPED ELEMENTS 5 SETTINGS Figure 5–92: THREE-POLE BREAKER FAILURE, TIMERS (Sheet 2 of 2) 5-176 M60 Motor Protection System GE Multilin...
Page 315 The time delay is adjustable from 0 to 600.00 seconds in steps of 0.01. The undervoltage elements can also be programmed to have an inverse time delay char- acteristic. GE Multilin M60 Motor Protection System 5-177...
Page 316 V = secondary voltage applied to the relay = pickup level pickup % of voltage pickup 842788A1.CDR Figure 5–93: INVERSE TIME UNDERVOLTAGE CURVES At 0% of pickup, the operating time equals the UNDERVOLTAGE DELAY setting. NOTE 5-178 M60 Motor Protection System GE Multilin...
Page 317 Source VT = Wye FLEXLOGIC OPERAND SETTING PHASE UV1 PKP PHASE UV1 MODE: FLEXLOGIC OPERAND Phase to Ground Phase to Phase PHASE UV1 OP FLEXLOGIC OPERAND PHASE UV1 DPO 827039AB.CDR Figure 5–94: PHASE UNDERVOLTAGE1 SCHEME LOGIC GE Multilin M60 Motor Protection System 5-179...
Page 318 FLEXLOGIC OPERAND PHASE OV1 PKP 827066A7.CDR Figure 5–95: PHASE OVERVOLTAGE SCHEME LOGIC > × If the source VT is wye-connected, then the phase overvoltage pickup condition is Pickup for V and V NOTE 5-180 M60 Motor Protection System GE Multilin...
Page 319 “Definite time”. The source assigned to this element must be configured for a phase VT. NEUTRAL OV1 CURVE VT errors and normal voltage unbalance must be considered when setting this element. This function requires the VTs to be wye-connected. Figure 5–96: NEUTRAL OVERVOLTAGE1 SCHEME LOGIC GE Multilin M60 Motor Protection System 5-181...
Page 320 NEG SEQ OV1 DPO NEG SEQ OV1 OP SETTING ≥ V_2 or 3 × V_2 PKP NEG SEQ OV1 SIGNAL SOURCE: Wye VT Delta VT 3 × V_2 827839A3.CDR Figure 5–97: NEGATIVE-SEQUENCE OVERVOLTAGE SCHEME LOGIC 5-182 M60 Motor Protection System GE Multilin...
Page 321: Voltage Elements
AUX UV1 EVENTS: MESSAGE Disabled The M60 contains one auxiliary undervoltage element for each VT bank. This element is intended for monitoring undervolt- age conditions of the auxiliary voltage. The selects the voltage level at which the time undervoltage ele- AUX UV1 PICKUP ment starts timing.
Page 322 AUX OV1 EVENTS: MESSAGE Disabled The M60 contains one auxiliary overvoltage element for each VT bank. This element is intended for monitoring overvoltage conditions of the auxiliary voltage. The nominal secondary voltage of the auxiliary voltage channel entered under SYSTEM ...
Page 323: Control Elements
If more than one operate-type operand is required, it may be assigned directly from the trip bus menu. GE Multilin M60 Motor Protection System 5-185...
Page 324 TRIP BUS 1 PKP = Enabled TRIP BUS 1 BLOCK = Off SETTINGS TRIP BUS 1 LATCHING = Enabled TRIP BUS 1 RESET = Off FLEXLOGIC OPERAND RESET OP 842023A1.CDR Figure 5–101: TRIP BUS LOGIC 5-186 M60 Motor Protection System GE Multilin...
Page 325: Setting Groups
The assigned operand is used to control the “On” state of a particular settings group. VIRTUAL OUTPUT 1 GE Multilin M60 Motor Protection System 5-187...
Page 326: Selector Switch
Range: FlexLogic™ operand SELECTOR 1 3BIT ACK: MESSAGE Range: Restore, Synchronize, Sync/Restore SELECTOR 1 POWER-UP MESSAGE MODE: Restore Range: Self-reset, Latched, Disabled SELECTOR 1 TARGETS: MESSAGE Self-reset Range: Disabled, Enabled SELECTOR 1 EVENTS: MESSAGE Disabled 5-188 M60 Motor Protection System GE Multilin...
Page 327 • SELECTOR 1 3BIT A0, A1, and A2: These settings specify a three-bit control input of the selector. The three-bit con- trol word pre-selects the position using the following encoding convention: POSITION rest GE Multilin M60 Motor Protection System 5-189...
Page 328 The selector position pre-selected via the stepping up control input has not been confirmed before the time out. SELECTOR 1 BIT ALARM The selector position pre-selected via the three-bit control input has not been confirmed before the time out. 5-190 M60 Motor Protection System GE Multilin...
Page 329 3BIT A1 3BIT A2 POS 1 POS 2 POS 3 POS 4 POS 5 POS 6 POS 7 BIT 0 BIT 1 BIT 2 STP ALARM BIT ALARM ALARM 842737A1.CDR Figure 5–103: TIME-OUT MODE GE Multilin M60 Motor Protection System 5-191...
Page 330 Make the following changes to selector switch element in the    SETTINGS CONTROL ELEMENTS SELECTOR SWITCH menu to assign control to user programmable pushbutton 1 and contact inputs 1 through 3: SELECTOR SWITCH 1 5-192 M60 Motor Protection System GE Multilin...
Page 331 3-bit acknowledge SELECTOR 1 BIT ALARM 3-bit position out SELECTOR 1 ALARM SELECTOR 1 PWR ALARM SELECTOR 1 BIT 0 SELECTOR 1 BIT 1 SELECTOR 1 BIT 2 842012A2.CDR Figure 5–105: SELECTOR SWITCH LOGIC GE Multilin M60 Motor Protection System 5-193...
Page 332: Underfrequency
SETTING ≤ 0 < f PICKUP UNDERFREQ 1 OP UNDERFREQ 1 ACTUAL VALUES MIN VOLT / AMP: UNDERFREQ 1 SOURCE: ≥ Level Minimum VOLT / AMP Frequency 827079A8.CDR Figure 5–106: UNDERFREQUENCY SCHEME LOGIC 5-194 M60 Motor Protection System GE Multilin...
Page 333: Overfrequency
OVERFREQ 1 BLOCK: OVERFREQ 1 RESET OVERFREQ 1 PKP DELAY : Off = 0 OVERFREQ 1 DPO OVERFREQ 1 OP SETTING ≥ PICKUP OVERFREQ 1 SOURCE: Frequency 827832A5.CDR Figure 5–107: OVERFREQUENCY SCHEME LOGIC GE Multilin M60 Motor Protection System 5-195...
Page 334: Motor Start Supervision
A method to prevent starting is by wiring an M60 output contact actuated by motor start supervision elements in the motor energizing control circuit. The output contact changes state only when the motor is stopped to accommodate control circuits that must be continuously energized such as a contactor.
Page 335 STARTS-PER-HOUR DPO STARTS-PER-HOUR OP FLEXLOGIC OPERANDS ACTUAL VALUE MOTOR STARTING STARTS/HR LOCKOUT MOTOR OFFLINE LOCKOUT TIME SETTINGS SETTINGS / SYSTEM SETUP / MOTOR / EMERGENCY RESTART: 833015A2.CDR Figure 5–108: MAXIMUM STARTING RATE SCHEME LOGIC GE Multilin M60 Motor Protection System 5-197...
Page 336 TIME-BTWN-STARTS DPO FLEXLOGIC OPERAND MOTOR STARTING TIME-BTWN-STARTS OP MOTOR OFFLINE ACTUAL VALUE SETTINGS BTWN STARTS LOCKOUT SETTINGS / SYSTEM SETUP / MOTOR / EMERGENCY RESTART: 833016A2.CDR Figure 5–109: TIME BETWEEN STARTS SCHEME LOGIC 5-198 M60 Motor Protection System GE Multilin...
Page 337: Reduced Voltage Starting
Range: 1.0 to 600.0 s in steps of 0.1 REDUCED VOLT TIMER: MESSAGE 10.0 s Range: FlexLogic™ operand REDUCED VOLT BLOCK: MESSAGE Range: Self-reset, Latched, Disabled REDUCED VOLT TARGET: MESSAGE Self-reset Range: Disabled, Enabled REDUCED VOLT EVENTS: MESSAGE Disabled GE Multilin M60 Motor Protection System 5-199...
Page 338 5.7 CONTROL ELEMENTS 5 SETTINGS The M60 can control the transition of a motor start from reduced to full voltage. This feature uses motor load and a supervi- sory timer to initiate a one second control signal (the operand) that can be used to switch to full volt- REDUCED VOLT CTRL age.
Page 339: Digital Elements
Range: Disabled, Enabled DIG ELEMENT MESSAGE PICKUP LED: Enabled Range: FlexLogic™ operand DIG ELEM 1 BLOCK: MESSAGE Range: Self-reset, Latched, Disabled DIGITAL ELEMENT MESSAGE TARGET: Self-reset Range: Disabled, Enabled DIGITAL ELEMENT MESSAGE EVENTS: Disabled GE Multilin M60 Motor Protection System 5-201...
Page 340 If the circuit presents a high resis- tance, the trickle current will fall below the monitor threshold and an alarm would be declared. 5-202 M60 Motor Protection System GE Multilin...
Page 341 The settings to use digital element 1 to monitor the breaker trip circuit are indicated below (EnerVista UR Setup example shown): setting should be greater than the operating time of the breaker to avoid nuisance alarms. PICKUP DELAY NOTE GE Multilin M60 Motor Protection System 5-203...
Page 342 “Off”. In this case, the settings are as follows (EnerVista UR Setup example shown). Figure 5–115: TRIP CIRCUIT EXAMPLE 2 The wiring connection for two examples above is applicable to both form-A contacts with voltage monitoring and solid-state contact with voltage monitoring. NOTE 5-204 M60 Motor Protection System GE Multilin...
Page 343: Digital Counters
–2,147,483,648 counts, the counter will rollover to +2,147,483,647. • COUNTER 1 BLOCK: Selects the FlexLogic™ operand for blocking the counting operation. All counter operands are blocked. GE Multilin M60 Motor Protection System 5-205...
Page 344 COUNTER 1 RESET: COUNTER 1 FROZEN: Off = 0 STORE DATE & TIME Date & Time SETTING COUNT1 FREEZE/RESET: Off = 0 827065A1.VSD SETTING COUNT1 FREEZE/COUNT: Off = 0 Figure 5–116: DIGITAL COUNTER SCHEME LOGIC 5-206 M60 Motor Protection System GE Multilin...
Page 345: Monitoring Elements
See page 5–213.   VT FUSE FAILURE 3 MESSAGE See page 5–213.   VT FUSE FAILURE 4 MESSAGE See page 5–213.   BROKEN ROTOR BAR MESSAGE See page 5–214.  GE Multilin M60 Motor Protection System 5-207...
Page 346 Voltage drop measured from either side of the breaker during the flashover period, Voltage difference drop, and Measured flashover current through the breaker. Furthermore, the scheme is applicable for cases where either one or two sets of three-phase voltages are available across the breaker. 5-208 M60 Motor Protection System GE Multilin...
Page 347 This application do not require detection of breaker status via a 52a contact, as it uses a voltage difference larger than the setting. However, monitoring the breaker contact will ensure scheme stability. BRK 1 FLSHOVR DIFF V PKP GE Multilin M60 Motor Protection System 5-209...
Page 348 BRK 1 FLSHOVR SPV A to BRK 1 FLSHOVR SPV C: These settings specifiy FlexLogic™ operands (per breaker pole) that supervise the operation of the element per phase. Supervision can be provided by operation of other protec- 5-210 M60 Motor Protection System GE Multilin...
Page 349 A six-cycle time delay applies after the selected Flex- Logic™ operand resets. • BRK FLSHOVR PKP DELAY: This setting specifies the time delay to operate after a pickup condition is detected. GE Multilin M60 Motor Protection System 5-211...
Page 350 5.7 CONTROL ELEMENTS 5 SETTINGS Figure 5–117: BREAKER FLASHOVER SCHEME LOGIC 5-212 M60 Motor Protection System GE Multilin...
Page 351 An additional condition is introduced to inhibit a fuse failure declaration when the monitored circuit is de-energized; positive sequence voltage and current are both below threshold levels. The function setting enables and disables the fuse failure feature for each source. Figure 5–118: VT FUSE FAIL SCHEME LOGIC GE Multilin M60 Motor Protection System 5-213...
Page 352 On the other hand, while the motor load is small, there is not enough resolution to accurately calculate a miniscule spectral component caused by a rotor bar fail- ure. 5-214 M60 Motor Protection System GE Multilin...
Page 353 Using the same values from previous example, this value should be programmed as follows. – sf max 0.3 min 2sf – end_offset (EQ 5.50) × × 0.01 60 Hz 0.40 Hz – – GE Multilin M60 Motor Protection System 5-215...
Page 354 This setting can be left at its default value since the element updates its state one to two times per minute. • BRB BLOCK: This setting selects a FlexLogic™ operand used to block the broken rotor bar detection feature. Typi- cally, a panel cut-off switch or other user-specified conditions blocks this function. 5-216 M60 Motor Protection System GE Multilin...
Page 355: Inputs And Outputs
The DC input voltage is compared to a user-settable threshold. A new contact input state must be maintained for a user- settable debounce time in order for the M60 to validate the new contact state. In the figure below, the debounce time is set at 2.5 ms;...
Page 356 Event Records menu, make the following settings changes: "Breaker Closed (52b)" CONTACT INPUT H5A ID: "Enabled" CONTACT INPUT H5A EVENTS: Note that the 52b contact is closed when the breaker is open and open when the breaker is closed. 5-218 M60 Motor Protection System GE Multilin...
Page 357: Virtual Inputs
SETTING “Virtual Input 1 to OFF = 0” VIRTUAL INPUT 1 ID: (Flexlogic Operand) SETTING Virt Ip 1 VIRTUAL INPUT 1 TYPE: Latched Self - Reset 827080A2.CDR Figure 5–120: VIRTUAL INPUTS SCHEME LOGIC GE Multilin M60 Motor Protection System 5-219...
Page 358: Contact Outputs
The most dependable protection of the initiating contact is provided by directly measuring current in the tripping circuit, and using this parameter to control resetting of the initiating relay. This scheme is often called trip seal-in. This can be realized in the M60 using the FlexLogic™ operand to seal-in the contact output as follows: CONT OP 1 ION “Cont Op 1"...
Page 359 5.8 INPUTS AND OUTPUTS The M60 latching output contacts are mechanically bi-stable and controlled by two separate (open and close) coils. As such they retain their position even if the relay is not powered up. The relay recognizes all latching output contact cards and pop- ulates the setting menu accordingly.
Page 360: Virtual Outputs
FlexLogic™ equations. Any change of state of a virtual output can be logged as an event if programmed to do so. For example, if Virtual Output 1 is the trip signal from FlexLogic™ and the trip relay is used to signal events, the settings would be programmed as follows: 5-222 M60 Motor Protection System GE Multilin...
Page 361: Remote Devices
The remote input/output facility provides for 32 remote inputs and 64 remote outputs. b) LOCAL DEVICES: ID OF DEVICE FOR TRANSMITTING GSSE MESSAGES In a M60 relay, the device ID that represents the IEC 61850 GOOSE application ID (GoID) name string sent as part of each GOOSE message is programmed in the ...
Page 362: Remote Inputs
This setting identifies the Ethernet application identification in the GOOSE message. It should match the corre- sponding settings on the sending device. setting provides for the choice of the M60 fixed (DNA/UserSt) dataset (that is, containing REMOTE DEVICE 1 DATASET DNA and UserSt bit pairs), or one of the configurable datasets.
Page 363: Remote Double-Point Status Inputs
REMOTE OUTPUTS DNA BIT PAIRS REMOTE OUPUTS DNA- 1(32) BIT PAIR Range: FlexLogic™ operand  REMOTE OUTPUTS DNA- 1 OPERAND:  DNA- 1 BIT PAIR Range: Disabled, Enabled DNA- 1 EVENTS: MESSAGE Disabled GE Multilin M60 Motor Protection System 5-225...
Page 364: Resetting
RESET OP to identify the source of the command. The setting RESET OP (PUSHBUTTON) RESET OP (COMMS) RESET OP (OPERAND) shown above selects the operand that will create the operand. RESET OP (OPERAND) 5-226 M60 Motor Protection System GE Multilin...
Page 365: Direct Inputs And Outputs
FlexLogic™ operand that determines the state of this direct output. c) APPLICATION EXAMPLES The examples introduced in the earlier Direct inputs and outputs section (part of the Product Setup section) are continued below to illustrate usage of the direct inputs and outputs. GE Multilin M60 Motor Protection System 5-227...
Page 366 5.8 INPUTS AND OUTPUTS 5 SETTINGS EXAMPLE 1: EXTENDING INPUT/OUTPUT CAPABILITIES OF A M60 RELAY Consider an application that requires additional quantities of digital inputs or output contacts or lines of programmable logic that exceed the capabilities of a single UR-series chassis. The problem is solved by adding an extra UR-series IED, such as the C30, to satisfy the additional inputs/outputs and programmable logic requirements.
Page 367 "3" (effectively, this is a message from IED 1) DIRECT INPUT 6 BIT NUMBER: UR IED 2: "1" DIRECT INPUT 5 DEVICE ID: "2" DIRECT INPUT 5 BIT NUMBER: "3" DIRECT INPUT 6 DEVICE ID: "2" DIRECT INPUT 6 BIT NUMBER: GE Multilin M60 Motor Protection System 5-229...
Page 368: Teleprotection Inputs And Outputs
Range: Off, On, Latest/Off, Latest/On TELEPROT INPUT 2-1 MESSAGE DEFAULT: Off Range: Off, On, Latest/Off, Latest/On TELEPROT INPUT 2-2 MESSAGE DEFAULT: Off ↓ Range: Off, On, Latest/Off, Latest/On TELEPROT INPUT 2-16 MESSAGE DEFAULT: Off 5-230 M60 Motor Protection System GE Multilin...
Page 369 (teleprotection outputs at the sending end or corresponding teleprotection inputs at the receiving end). On three-terminal two-channel systems, redundancy is achieved by programming signal re-transmittal in the case of channel failure between any pair of relays. GE Multilin M60 Motor Protection System 5-231...
Page 370: Iec 61850 Goose Analogs
GOOSE analog input value. GOOSE Analogs are floating-point values, with no units. The GOOSE UNIT and PU base settings allow the user to configure GOOSE Analog, so that it can be used in a FlexElement. 5-232 M60 Motor Protection System GE Multilin...
Page 371 GOOSE ANALOG 1 PU: This setting specifies the per-unit base factor when using the GOOSE analog input FlexAna- log™ values in other M60 features, such as FlexElements™. The base factor is applied to the GOOSE analog input FlexAnalog quantity to normalize it to a per-unit quantity. The base units are described in the following table.
Page 372: Iec 61850 Goose Integers
“Default Value”, then the value of the GOOSE uinteger input is defined by the setting. UINTEGER 1 DEFAULT The GOOSE integer input FlexInteger™ values are available for use in other M60 functions that use FlexInteger™ values. 5-234 M60 Motor Protection System...
Page 373 –20 to +180 MW; in this case the value would be “–20” and the DCMA INPUT H1 MIN VALUE DCMA INPUT H1 MAX value “180”. Intermediate values between the min and max values are scaled linearly. VALUE GE Multilin M60 Motor Protection System 5-235...
Page 374: Transducer Inputs And Outputs
RTD INPUT H1 ID: An alphanumeric ID is assigned to the channel. This ID will be included in the channel actual val- ues. It is also used to reference the channel as the input parameter to features designed to measure this type of parameter. 5-236 M60 Motor Protection System GE Multilin...
Page 375 A value of “None” specifies that the RTD will operate individually and not part of any RTD group. All RTDs programmed to “Stator” are used for RTD biasing of the M60 ther- mal model.
Page 376: Rrtd Inputs
 RRTD See page 5-239.    RRTD MESSAGE See page 5-239.  ↓  RRTD 12 MESSAGE See page 5-239.  Menus are available to configure each of the remote RTDs. 5-238 M60 Motor Protection System GE Multilin...
Page 377 5.9 TRANSDUCER INPUTS AND OUTPUTS It is recommended to use the M60 to configure the RRTD parameters. If the RRTDPC software is used to change the RRTD settings directly (the application and type settings), then one of the following two operations is required for changes to be reflected in the M60.
Page 378 ” If the RRTD communication link with the M60 is broken, then the last temperature actual values are retained until the RRTD communication failure is detected. When this occurs, a RRTD COMM FAILURE self-test alarm and target message is gen- erated, and an event is logged in the event recorder and the temperature actual values reset to 0.
Page 379 RTD group. All remote RTDs programmed to “Stator” are used for RTD biasing of the M60 thermal model. Common groups are provided for rotating machines applications such as ambient, bearing, group 1, or group 2. If the setting value is “Group”, then it is allowed to issue a trip if N –...
Page 380: Dcma Outputs
. The follow- MIN VAL MAX VAL RANGE ing equation is applied: < if x  MIN VAL  if x >  MAX VAL (EQ 5.51)  otherwise  – MIN VAL 5-242 M60 Motor Protection System GE Multilin...
Page 381 20% overload compared to the nominal. The nominal three-phase power is: × × × 13.8 kV 0.8 kA 17.21 MW (EQ 5.53) The three-phase power with 20% overload margin is: × 1.2 17.21 MW 20.65 MW (EQ 5.54) GE Multilin M60 Motor Protection System 5-243...
Page 382 400 kV 400 kV × ------------------ - × ------------------ - 161.66 kV, 254.03 kV (EQ 5.60) The base unit for voltage (refer to the FlexElements section in this chapter for additional details) is: 5-244 M60 Motor Protection System GE Multilin...
Page 383 254.03 kV 1.27 kV – • ±0.5% of reading For example, under nominal conditions, the positive-sequence reads 230.94 kV and the worst-case error is 0.005 x 230.94 kV + 1.27 kV = 2.42 kV. GE Multilin M60 Motor Protection System 5-245...
Page 384: Test Mode
TEST MODE FORCING: MESSAGE The M60 provides a test facility to verify the functionality of contact inputs and outputs, some communication channels and the phasor measurement unit (where applicable), using simulated conditions. The test mode is indicated on the relay face- plate by a Test Mode LED indicator.
Page 385: Force Contact Inputs
Following a restart, power up, settings TEST MODE FUNCTION upload, or firmware upgrade, the test mode will remain at the last programmed value. This allows a M60 that has been placed in isolated mode to remain isolated during testing and maintenance activities. On restart, the TEST MODE FORCING setting and the force contact input and force contact output settings all revert to their default states.
Page 386: Force Contact Outputs
PUSHBUTTON 1 FUNCTION input 1 to initiate the Test mode, make the following changes in the menu:   SETTINGS TESTING TEST MODE “Enabled” and “ ” TEST MODE FUNCTION: TEST MODE INITIATE: 5-248 M60 Motor Protection System GE Multilin...
Page 387  STATUS  IEC 61850 See page 6-9.  GOOSE UINTEGERS  EGD PROTOCOL See page 6-9.  STATUS  TELEPROT CH TESTS See page 6-10.   ETHERNET SWITCH See page 6-11.  GE Multilin M60 Motor Protection System...
Page 388: Dcma Inputs
  OSCILLOGRAPHY See page 6-26.   DATA LOGGER See page 6-26.   ACTUAL VALUES  MODEL INFORMATION See page 6-27.  PRODUCT INFO   FIRMWARE REVISIONS See page 6-27.  M60 Motor Protection System GE Multilin...
Page 389: Motor
The present status of the contact inputs is shown here. The first line of a message display indicates the ID of the contact input. For example, ‘Cont Ip 1’ refers to the contact input in terms of the default name-array index. The second line of the display indicates the logic state of the contact input. GE Multilin M60 Motor Protection System...
Page 390: Virtual Inputs
The present state of the remote double-point status inputs is shown here. The actual values indicate if the remote double- point status inputs are in the on (close), off (open), intermediate, or bad state. M60 Motor Protection System GE Multilin...
Page 391: Teleprotection Inputs
For form-A contact outputs, the state of the voltage and current detectors is displayed as Off, VOff, IOff, On, IOn, and VOn. For form-C contact outputs, the state is displayed as Off or On. NOTE GE Multilin M60 Motor Protection System...
Page 392: Virtual Outputs
The present state of up to 16 programmed remote devices is shown here. The message indi- ALL REMOTE DEVICES ONLINE cates whether or not all programmed remote devices are online. If the corresponding state is "No", then at least one required remote device is not online. M60 Motor Protection System GE Multilin...
Page 393: Digital Counters
Range: Current Position / 7 SELECTOR SWITCH 2 MESSAGE POSITION: 0/7 The display shows both the current position and the full range. The current position only (an integer from 0 through 7) is the actual value. GE Multilin M60 Motor Protection System...
Page 394: Flex States
MESSAGE CH1: 0 AVG MSG RETURN MESSAGE TIME CH2: 0 ms UNRETURNED MSG MESSAGE COUNT CH2: 0 CRC FAIL COUNT MESSAGE CH2: 0 DIRECT INPUT MESSAGE DIRECT INPUT MESSAGE ↓ DIRECT INPUT 32: MESSAGE M60 Motor Protection System GE Multilin...
Page 395: Direct Devices Status
UINT INPUT 16 MESSAGE The M60 Motor Protection System is provided with optional IEC 61850 communications capability. This feature is specified as a software option at the time of ordering. Refer to the Ordering section of chapter 2 for additional details. The IEC 61850 protocol features are not available if CPU type E is ordered.
Page 396: Teleprotection Channel Tests
“FAIL” message will be displayed. The “N/A” value appears if the local relay ID is set to a default value of “0”, the chan- nel is failed, or if the teleprotection inputs/outputs are not enabled. 6-10 M60 Motor Protection System GE Multilin...
Page 397: Ethernet Switch
SWITCH MAC ADDRESS: MESSAGE 00A0F40138FA These actual values appear only if the M60 is ordered with an Ethernet switch module (type 2S or 2T). The status informa- tion for the Ethernet switch is shown in this menu. • SWITCH 1 PORT STATUS to SWITCH 6 PORT STATUS: These values represents the receiver status of each port on the Ethernet switch.
Page 398: Metering Conventions
PF = Lag WATTS = Negative VARS = Positive PF = Lead PF = Lag PF = Lead Current UR RELAY 827239AC.CDR S=VI Generator Figure 6–1: FLOW DIRECTION OF SIGNED VALUES FOR WATTS AND VARS 6-12 M60 Motor Protection System GE Multilin...
Page 399 ABC phase rotation: • ACB phase rotation: -- - V -- - V -- - V -- - V -- - V -- - V The above equations apply to currents as well. GE Multilin M60 Motor Protection System 6-13...
Page 400 The power system voltages are phase-referenced – for simplicity – to VAG and VAB, respectively. This, however, is a relative matter. It is important to remember that the M60 displays are always referenced as specified under SETTINGS ...
Page 401: Stator Differential
MOTOR UNBALANCE: This value is the amount of unbalance in the motor currents. A full explanation of the calcula- tion of this value is presented for the Amp Unbalance element • U/B BIASED MOTOR LOAD: Unbalance Bias Motor Load shows the equivalent motor heating current caused by the unbalance k factor. GE Multilin M60 Motor Protection System 6-15...
Page 402: Sources
PHASOR Ia: MESSAGE 0.000 0.0° SRC 1 PHASOR Ib: MESSAGE 0.000 0.0° SRC 1 PHASOR Ic: MESSAGE 0.000 0.0° SRC 1 PHASOR In: MESSAGE 0.000 0.0° SRC 1 ZERO SEQ I0: MESSAGE 0.000 0.0° 6-16 M60 Motor Protection System GE Multilin...
Page 403 SRC 1 RMS Vbc: MESSAGE 0.00 SRC 1 RMS Vca: MESSAGE 0.00 SRC 1 PHASOR Vab: MESSAGE 0.000 0.0° SRC 1 PHASOR Vbc: MESSAGE 0.000 0.0° SRC 1 PHASOR Vca: MESSAGE 0.000 0.0° GE Multilin M60 Motor Protection System 6-17...
Page 404 REACTIVE PWR MESSAGE φc: 0.000 SRC 1 APPARENT PWR MESSAGE 3φ: 0.000 SRC 1 APPARENT PWR MESSAGE φa: 0.000 SRC 1 APPARENT PWR MESSAGE φb: 0.000 SRC 1 APPARENT PWR MESSAGE φc: 0.000 6-18 M60 Motor Protection System GE Multilin...
Page 405: Sensitive Directional Power
6.3.5 SENSITIVE DIRECTIONAL POWER   PATH: ACTUAL VALUES METERING SENSITIVE DIRECTIONAL POWER  SENSITIVE DIRECTIONAL POWER 1  DIRECTIONAL POWER 3Φ: 0.000 W DIRECTIONAL POWER 2 MESSAGE 3Φ: 0.000 W GE Multilin M60 Motor Protection System 6-19...
Page 406: Broken Rotor Bar
LOAD DEV. AT BRB MAX: This value indicates the motor load standard deviation at the time when data for the maxi- mum broken rotor bar was acquired. • TIME OF MAXIMUM BRB: This value indicates the time stamp of the maximum broken rotor bar component level. 6-20 M60 Motor Protection System GE Multilin...
Page 407: Tracking Frequency
THERMAL MODEL BASE = 10 minutes (Model Lockout Time) THERMAL MODEL BASE = 1.00 pu of FLA (Thermal Model Load) (Biased Motor Load) THERMAL MODEL BASE = 10 seconds (Trip Time on Overload) GE Multilin M60 Motor Protection System 6-21...
Page 408: Iec 61580 Goose Analog Values
MESSAGE 0.000 The M60 Motor Protection System is provided with optional IEC 61850 communications capability. This feature is specified as a software option at the time of ordering. Refer to the Ordering section of chapter 2 for additional details. The IEC 61850 protocol features are not available if CPU type E is ordered.
Page 409: Records
START 1 EFFECTIVE MESSAGE CURRENT: 5.85 x FLA START 1 PEAK MESSAGE CURRENT: 6.70 x FLA Up to five motor starts are displayed. When the buffer is full, the newest record overwrites the oldest record. GE Multilin M60 Motor Protection System 6-23...
Page 410: Motor Learned Data
Learned values associated with motor acceleration require the acceleration time function to be enabled. The learned features are not be used until at least N + 1 successful motor starts have occurred. NOTE 6-24 M60 Motor Protection System GE Multilin...
Page 411: Event Records
EVENT: XXXX  RESET OP(PUSHBUTTON) ↓ EVENT: 3 EVENT 3 MESSAGE POWER ON DATE: 2000/07/14 EVENT: 2 EVENT 3 MESSAGE POWER OFF TIME: 14:53:00.03405 EVENT: 1 Date and Time Stamps MESSAGE EVENTS CLEARED GE Multilin M60 Motor Protection System 6-25...
Page 412: Oscillography
It counts up at the defined sampling rate. If the data logger channels are defined, then both values are static. Refer to the  menu for clearing data logger records. COMMANDS CLEAR RECORDS 6-26 M60 Motor Protection System GE Multilin...
Page 413: Product Information
6.5PRODUCT INFORMATION 6.5.1 MODEL INFORMATION   PATH: ACTUAL VALUES PRODUCT INFO MODEL INFORMATION Range: standard GE order code format;  MODEL INFORMATION ORDER CODE LINE 1: example order code shown  M60-A00-HCH-F8A-H6A Range: standard GE order code format ORDER CODE LINE 2:...
Page 414 6.5 PRODUCT INFORMATION 6 ACTUAL VALUES 6-28 M60 Motor Protection System GE Multilin...
Page 415: Commands And
The states of up to 64 virtual inputs are changed here. The first line of the display indicates the ID of the virtual input. The second line indicates the current or selected status of the virtual input. This status will be a state off (logic 0) or on (logic 1). GE Multilin M60 Motor Protection System...
Page 416: Clear Records
24-hour clock. The complete date, as a minimum, must be entered to allow execution of this com- mand. The new time will take effect at the moment the ENTER key is clicked. M60 Motor Protection System GE Multilin...
Page 417: Relay Maintenance
Various self-checking diagnostics are performed in the background while the M60 is running, and diagnostic information is stored on the non-volatile memory from time to time based on the self-checking result. Although the diagnostic information is cleared before the M60 is shipped from the factory, the user may want to clear the diagnostic information for themselves under certain circumstances.
Page 418: Targets Menu
The critical fail relay on the power supply module is de-energized. • All other output relays are de-energized and are prevented from further operation. • The faceplate In Service LED indicator is turned off. • event is recorded. RELAY OUT OF SERVICE M60 Motor Protection System GE Multilin...
Page 419 Contact Factory (xxx) • Latched target message: Yes. • Description of problem: One or more installed hardware modules is not compatible with the M60 order code. • How often the test is performed: Module dependent. • What to do: Contact the factory and supply the failure code noted in the display. The “xxx” text identifies the failed mod- ule (for example, F8L).
Page 420 How often the test is performed: Monitored every five seconds. An error is issued after five consecutive failures • What to do: Check the M60 device and switch IP configuration settings. Check for incorrect UR port (port 7) settings on the Ethernet switch. Check the power to the switch.
Page 421 What to do: Check direct input and output configuration and wiring. REMOTE DEVICE FAIL: COMM Path Incomplete • Latched target message: No. • Description of problem: One or more GOOSE devices are not responding. GE Multilin M60 Motor Protection System...
Page 422 Description of problem: The ambient temperature is greater than the maximum operating temperature (+80°C). • How often the test is performed: Every hour. • What to do: Remove the M60 from service and install in a location that meets operating temperature standards. UNEXPECTED RESTART: Press “RESET” key •...
Page 423 Brick output failing to respond to an output command can only be detected while the command is active, and so in this case the target is latched. A latched target can be unlatched by pressing the faceplate reset key if the command has ended, however the output may still be non-functional. GE Multilin M60 Motor Protection System...
Page 424 7.2 TARGETS 7 COMMANDS AND TARGETS 7-10 M60 Motor Protection System GE Multilin...
Page 425: Security
When entering a settings or command password via EnerVista or any serial interface, the user must enter the correspond- ing connection password. If the connection is to the back of the M60, the remote password must be used. If the connection is to the RS232 port of the faceplate, the local password must be used.
Page 426: Password Security Menu
If an entered password is lost (or forgotten), consult the factory with the corresponding ENCRYPTED PASSWORD If the setting and command passwords are identical, then this one password allows access to both commands and settings. NOTE M60 Motor Protection System GE Multilin...
Page 427: Remote Passwords
 ACCESS LEVEL  SUPERVISION  TIMEOUTS Range: 2 to 5 in steps of 1 INVALID ATTEMPTS MESSAGE BEFORE LOCKOUT: 3 Range: 5 to 60 minutes in steps of 1 PASSWORD LOCKOUT MESSAGE DURATION: 5 min GE Multilin M60 Motor Protection System...
Page 428: Dual Permission Security Access
INVALID ATTEMPS BEFORE LOCKOUT The M60 provides a means to raise an alarm upon failed password entry. Should password verification fail while accessing a password-protected level of the relay (either settings or commands), the FlexLogic™ operand is UNAUTHORIZED ACCESS asserted.
Page 429 If access is permitted and an off-to-on transition of the FlexLogic™ operand is detected, the timeout is restarted. The status of this timer is updated every 5 seconds. GE Multilin M60 Motor Protection System...
Page 430: Settings Security
(settings file templates) and online devices (online settings templates). The func- tionality is identical for both purposes. The settings template feature requires that both the EnerVista UR Setup software and the M60 firmware are at ver- sions 5.40 or higher.
Page 431 ADDING PASSWORD PROTECTION TO A TEMPLATE GE recommends that templates be saved with password protection to maximize security. When templates are created for online settings, the password is added during the initial template creation step. It does not need to be added after the template is created.
Page 432 Template Mode > View In Template Mode command. The template specifies that only the Pickup Curve Phase time overcurrent settings window without template applied. settings be available. 842858A1.CDR Figure 8–4: APPLYING TEMPLATES VIA THE VIEW IN TEMPLATE MODE COMMAND M60 Motor Protection System GE Multilin...
Page 433 Once a settings template is removed, it cannot be reapplied and a new settings template needs to be defined before use. Right-click the device in the Online or Offline Window area and select the Template Mode > Remove Template option. Enter the template password and click OK to continue. GE Multilin M60 Motor Protection System...
Page 434: Securing And Locking Flexlogic™ Equations
Select the Template Mode > View In Template Mode option to view the template. Optionally apply a password to the template by right-clicking the device and selecting the Template Mode > Pass- word Protect Template option. 8-10 M60 Motor Protection System GE Multilin...
Page 435 A serial number is viewable under Actual Values > Product Info > Model Information, the inside front panel, and the rear of the device. GE Multilin M60 Motor Protection System 8-11...
Page 436: Settings File Traceability
When a settings file is transfered to a M60 device, the date, time, and serial number of the M60 are sent back to EnerVista UR Setup and added to the settings file on the local PC. This infor- mation can be compared with the M60 actual values at any later date to determine if security has been compromised.
Page 437 With respect to the above diagram, the traceability feature is used as follows. The transfer date of a setting file written to a M60 is logged in the relay and can be viewed via EnerVista UR Setup or the front panel display. Likewise, the transfer date of a setting file saved to a local PC is logged in EnerVista UR Setup.
Page 438 ONLINE DEVICE TRACEABILITY INFORMATION The M60 serial number and file transfer date are available for an online device through the actual values. Select the Actual Values > Product Info > Model Information menu item within the EnerVista UR Setup online window as shown in the example below.
Page 439: Enervista Security Management System
Select the Security > User Management menu item to open the user management configuration window. Enter a username in the User field. The username must be between 4 and 20 characters in length. GE Multilin M60 Motor Protection System 8-15...
Page 440: Modifying User Privileges
The EnerVista security management system must be enabled. The following procedure describes how to modify user privileges. Select the Security > User Management menu item to open the user management configuration window. Locate the username in the User field. 8-16 M60 Motor Protection System GE Multilin...
Page 441 When this box is checked, the user will become an EnerVista URPlus Setup administrator, therefore receiving all of the administrative rights. Exercise caution when granting administrator rights. Click OK to save the changes to user to the security management system. GE Multilin M60 Motor Protection System 8-17...
Page 442 8.3 ENERVISTA SECURITY MANAGEMENT SYSTEM 8 SECURITY 8-18 M60 Motor Protection System GE Multilin...
Page 443: Theory Of Operation
9.1.1 CT SATURATION DETECTION The saturation detector of the M60 takes advantage of the fact that any CT operates correctly for a short period of time even under very large primary currents that would subsequently cause a very deep saturation. As a result of that, in the case of an external fault, the differential current stays very low during the initial period of linear operation of the CTs while the restraining signal develops rapidly.
Page 444 The differential- restraining trajectory The differential out of the differential characteristic characteristic for a entered certain period of time EXTERNAL FAULT and CT SATURATION SAT := 1 836729A1.CDR Figure 9–2: SATURATION DETECTOR STATE MACHINE M60 Motor Protection System GE Multilin...
Page 445: Commissioning
Injection to a particular M60 frequency element must be to its configured source and to the channels the source uses for frequency measurement. For frequency measurement, a source will use the first quantity configured in the following order: Phase voltages.
Page 446 1 second from test set time reading of ramp start to relay operation. Note that the M60 event records only show the “pickup delay” component, a definite time timer. This is exclusive of the time taken by the frequency responding component to pickup.
Page 447: Parameter Lists
Source 2 neutral current magnitude 6227 SRC 2 In Angle Degrees Source 2 neutral current angle 6228 SRC 2 Ig RMS Amps Source 2 ground current RMS 6230 SRC 2 Ig Mag Degrees Source 2 ground current magnitude GE Multilin M60 Motor Protection System...
Page 448 Source 4 neutral current angle 6356 SRC 4 Ig RMS Amps Source 4 ground current RMS 6358 SRC 4 Ig Mag Degrees Source 4 ground current magnitude 6360 SRC 4 Ig Angle Amps Source 4 ground current angle M60 Motor Protection System GE Multilin...
Page 449 SRC 2 Vab RMS Volts Source 2 phase AB voltage RMS 6737 SRC 2 Vbc RMS Volts Source 2 phase BC voltage RMS 6739 SRC 2 Vca RMS Volts Source 2 phase CA voltage RMS GE Multilin M60 Motor Protection System...
Page 450 SRC 4 Vcg RMS Volts Source 4 phase CG voltage RMS 6854 SRC 4 Vag Mag Volts Source 4 phase AG voltage magnitude 6856 SRC 4 Vag Angle Degrees Source 4 phase AG voltage angle M60 Motor Protection System GE Multilin...
Page 451 Source 2 phase A reactive power 7212 SRC 2 Qb Vars Source 2 phase B reactive power 7214 SRC 2 Qc Vars Source 2 phase C reactive power 7216 SRC 2 S Source 2 three-phase apparent power GE Multilin M60 Motor Protection System...
Page 452 1 actual value 13506 DCMA Inputs 2 Value dcmA input 2 actual value 13508 DCMA Inputs 3 Value dcmA input 3 actual value 13510 DCMA Inputs 4 Value dcmA input 4 actual value M60 Motor Protection System GE Multilin...
Page 453 RTD input 24 actual value 13576 RTD Inputs 25 Value RTD input 25 actual value 13577 RTD Inputs 26 Value RTD input 26 actual value 13578 RTD Inputs 27 Value RTD input 27 actual value GE Multilin M60 Motor Protection System...
Page 454 Remote RTD input 10 actual value 34762 RRTD RTD 11 Value °C Remote RTD input 11 actual value 34763 RRTD RTD 12 Value °C Remote RTD input 12 actual value 39425 FlexElement 1 Value FlexElement™ 1 actual value M60 Motor Protection System GE Multilin...
Page 455 IEC 61850 GOOSE analog input 20 45624 GOOSE Analog In 21 IEC 61850 GOOSE analog input 21 45626 GOOSE Analog In 22 IEC 61850 GOOSE analog input 22 45628 GOOSE Analog In 23 IEC 61850 GOOSE analog input 23 GE Multilin M60 Motor Protection System...
Page 456 45642 GOOSE Analog In 30 IEC 61850 GOOSE analog input 30 45644 GOOSE Analog In 31 IEC 61850 GOOSE analog input 31 45646 GOOSE Analog In 32 IEC 61850 GOOSE analog input 32 A-10 M60 Motor Protection System GE Multilin...
Page 457: Flexinteger Items
IEC61850 GOOSE UInteger input 13 9994 GOOSE UInt Input 14 IEC61850 GOOSE UInteger input 14 9996 GOOSE UInt Input 15 IEC61850 GOOSE UInteger input 15 9998 GOOSE UInt Input 16 IEC61850 GOOSE UInteger input 16 GE Multilin M60 Motor Protection System A-11...
Page 458 A.1 PARAMETER LISTS APPENDIX A A-12 M60 Motor Protection System GE Multilin...
Page 459: Introduction
Broadcast mode is only recognized when associated with function code 05h. For any other function code, a packet with broadcast mode slave address 0 will be ignored. GE Multilin M60 Motor Protection System...
Page 460: Algorithm
No: go to 8; Yes: G (+) A --> A and continue. Is j = 8? No: go to 5; Yes: continue i + 1 --> i Is i = N? No: go to 3; Yes: continue A --> CRC M60 Motor Protection System GE Multilin...
Page 461: Modbus Function Codes
Since some PLC implementations of Modbus only support one of function codes 03h and 04h. The M60 interpretation allows either function code to be used for reading one or more consecutive data registers. The data starting address will determine the type of data being read.
Page 462: Execute Operation (Function Code 05H
DATA STARTING ADDRESS - low DATA STARTING ADDRESS - low DATA - high DATA - high DATA - low DATA - low CRC - low CRC - low CRC - high CRC - high M60 Motor Protection System GE Multilin...
Page 463: Store Multiple Settings (Function Code 10H
PACKET FORMAT EXAMPLE (HEX) SLAVE ADDRESS SLAVE ADDRESS FUNCTION CODE FUNCTION CODE CRC - low order byte ERROR CODE CRC - high order byte CRC - low order byte CRC - high order byte GE Multilin M60 Motor Protection System...
Page 464: File Transfers
Last Cleared Date" to the present date and time. To read binary COMTRADE oscillography files, read the following filenames: OSCnnnn.CFG and OSCnnn.DAT Replace “nnn” with the desired oscillography trigger number. For ASCII format, use the following file names OSCAnnnn.CFG and OSCAnnn.DAT M60 Motor Protection System GE Multilin...
Page 465: Modbus Password Operation
When entering a settings or command password via EnerVista or any serial interface, the user must enter the correspond- ing connection password. If the connection is to the back of the M60, the remote password must be used. If the connection is to the RS232 port of the faceplate, the local password must be used.
Page 466: Memory Mapping
0 (Off) 0418 Virtual Input 25 State 0 to 1 F108 0 (Off) 0419 Virtual Input 26 State 0 to 1 F108 0 (Off) 041A Virtual Input 27 State 0 to 1 F108 0 (Off) M60 Motor Protection System GE Multilin...
Page 468 0 to 65535 F500 160A Field Latching Output Close Driver States 0 to 65535 F500 160B Field Latching Output Physical States 0 to 65535 F500 160C Field Unit Online/Offline States 0 to 65535 F500 B-10 M60 Motor Protection System GE Multilin...
Page 469 1813 Source 1 Neutral Current Angle -359.9 to 0 degrees F002 1814 Source 1 Ground Current RMS 0 to 999999.999 0.001 F060 1816 Source 1 Ground Current Magnitude 0 to 999999.999 0.001 F060 GE Multilin M60 Motor Protection System B-11...
Page 471 Breaker Flashover 1 Status Closed B 0 to 65535 F300 21AB Breaker Flashover 1 Status Closed C 0 to 65535 F300 21AC Breaker Flashover 1 Voltage Pickup Level 0 to 1.5 0.001 F001 GE Multilin M60 Motor Protection System B-13...
Page 472 0 to 4294967295 F003 2700 IEC 61850 Received uinteger 9 0 to 4294967295 F003 2702 IEC 61850 Received uinteger 10 0 to 4294967295 F003 2704 IEC 61850 Received uinteger 11 0 to 4294967295 F003 B-14 M60 Motor Protection System GE Multilin...
Page 473 -9999999 to 9999999 0.001 F004 34C6 DCMA Inputs 4 Value -9999999 to 9999999 0.001 F004 34C8 DCMA Inputs 5 Value -9999999 to 9999999 0.001 F004 34CA DCMA Inputs 6 Value -9999999 to 9999999 0.001 F004 GE Multilin M60 Motor Protection System B-15...
Page 474 -32768 to 32767 °C F002 3510 RTD Input 33 Value -32768 to 32767 °C F002 3511 RTD Input 34 Value -32768 to 32767 °C F002 3512 RTD Input 35 Value -32768 to 32767 °C F002 B-16 M60 Motor Protection System GE Multilin...
Page 475 Remote Ground CT 1 Secondary 0 to 1 F123 0 (1 A) 3899 Remote Phase VT 1 Connection 0 to 1 F100 0 (Wye) 389A Remote Phase VT 1 Secondary 25 to 240 F001 GE Multilin M60 Motor Protection System B-17...
Page 477 Field Shared Output 1 Unit Dest 2 0 to 8 F256 0 (None) 3DCA Field Shared Output 1 Channel Dest 2 1 to 15 F001 3DCB Field Shared Output 1 Events 0 to 1 F102 1 (Enabled) GE Multilin M60 Motor Protection System B-19...
Page 479 TCP Port Number for the Modbus protocol 1 to 65535 F001 40A4 TCP/UDP Port Number for the DNP Protocol 1 to 65535 F001 20000 40A5 TCP Port Number for the HTTP (Web Server) Protocol 1 to 65535 F001 GE Multilin M60 Motor Protection System B-21...
Page 480 DNP Object 32 Default Variation 0 to 5 F525 0 (1) Ethernet Switch (Read/Write Setting) 4148 Ethernet Switch IP Address 0 to 4294967295 F003 3232235778 414A Ethernet Switch Modbus IP Port Number 1 to 65535 F001 B-22 M60 Motor Protection System GE Multilin...
Page 481 Oscillography Digital Channel n (63 items) 0 to 65535 F300 Trip and Alarm LEDs (Read/Write Setting) 4260 Trip LED Input FlexLogic Operand 0 to 65535 F300 4261 Alarm LED Input FlexLogic Operand 0 to 65535 F300 GE Multilin M60 Motor Protection System B-23...
Page 483 Breaker 1 Function 0 to 1 F102 0 (Disabled) 4701 Breaker 1 Name F206 “Bkr 1" 4704 Breaker 1 Mode 0 to 1 F157 0 (3-Pole) 4705 Breaker 1 Open 0 to 65535 F300 GE Multilin M60 Motor Protection System B-25...
Page 484 4E08 Raw Field Data AC3 Angle 0 to 0.01 degree F002 4E09 Raw Field Data AC4 Mag 0 to 0.001 0.001 F003 4E0B Raw Field Data AC4 Angle 0 to 0.01 degree F002 B-26 M60 Motor Protection System GE Multilin...
Page 485 RTD Input 1 Events 0 to 1 F102 0 (Disabled) 5413 ...Repeated for RTD Input 2 5426 ...Repeated for RTD Input 3 5439 ...Repeated for RTD Input 4 544C ...Repeated for RTD Input 5 GE Multilin M60 Motor Protection System B-27...
Page 487 Neutral Instantaneous Overcurrent 1 Pickup 0 to 30 0.001 F001 1000 5C03 Neutral Instantaneous Overcurrent 1 Delay 0 to 600 0.01 F001 5C04 Neutral Instantaneous Overcurrent 1 Reset Delay 0 to 600 0.01 F001 GE Multilin M60 Motor Protection System B-29...
Page 489 0 to 1 F102 0 (Disabled) 64D1 Overfrequency 1 Block 0 to 65535 F300 64D2 Overfrequency 1 Source 0 to 5 F167 0 (SRC 1) 64D3 Overfrequency 1 Pickup 20 to 65 0.01 F001 6050 GE Multilin M60 Motor Protection System B-31...
Page 490 0 (Disabled) 66AB Reserved (5 items) 0 to 65535 F001 66B0 ...Repeated for Sensitive Directional Power 2 Underpower (Read/Write Grouped Setting) (2 modules) 66D0 Underpower 1 Function 0 to 1 F102 0 (Disabled) B-32 M60 Motor Protection System GE Multilin...
Page 491 69A2 Restart Delay Block 0 to 65535 F300 69A3 Restart Delay Target 0 to 2 F109 0 (Self-reset) 69A4 Restart Delay Events 0 to 1 F102 0 (Disabled) 69A5 Reserved (11 items) F001 GE Multilin M60 Motor Protection System B-33...
Page 492 Phase Directional Overcurrent 1 Pol V Threshold 0 to 3 0.001 F001 7265 Phase Directional Overcurrent 1 Block Overcurrent 0 to 1 F126 0 (No) 7266 Phase Directional Overcurrent 1 Target 0 to 2 F109 0 (Self-reset) B-34 M60 Motor Protection System GE Multilin...
Page 494 F001 7B05 Thermal Model Time Constant Stopped 1 to 65000 F001 7B06 Thermal Model Hot Cold Ratio 0.01 to 1 0.01 F001 7B07 Thermal Model RTD Bias 0 to 1 F102 0 (Disabled) B-36 M60 Motor Protection System GE Multilin...
Page 495 User Programmable Pushbutton 1 Target 0 to 2 F109 0 (Self-reset) 7B81 User Programmable Pushbutton 1 Events 0 to 1 F102 0 (Disabled) 7B82 User Programmable Pushbutton 1 LED Operand 0 to 65535 F300 GE Multilin M60 Motor Protection System B-37...
Page 496 0 to 65535 F001 7F10 ...Repeated for Neutral Overvoltage 2 7F20 ...Repeated for Neutral Overvoltage 3 Auxiliary Overvoltage (Read/Write Grouped Setting) (2 modules) 7F30 Auxiliary Overvoltage 1 Function 0 to 1 F102 0 (Disabled) B-38 M60 Motor Protection System GE Multilin...
Page 497 846B EGD Slow Producer Exchange 1 Data Rate 500 to 1000 F001 1000 846C EGD Slow Producer Exchange 1 Data Item 1 (50 items) 0 to 65535 F001 849E Reserved (50 items) F001 GE Multilin M60 Motor Protection System B-39...
Page 498 0 (None) 86DF Remote RTD 1 Block 0 to 65535 F300 86E0 Remote RTD 1 Open 0 to 2 F552 0 (None) 86E1 Remote RTD 1 Target 0 to 2 F109 0 (Self-Reset) B-40 M60 Motor Protection System GE Multilin...
Page 500 0 to 65535 F300 8E13 Trip Bus 1 Input 16 0 to 65535 F300 8E14 Trip Bus 1 Latching 0 to 1 F102 0 (Disabled) 8E15 Trip Bus 1 Reset 0 to 65535 F300 B-42 M60 Motor Protection System GE Multilin...
Page 502 IEC 61850 GOOSE uinteger Input 1 Mode 0 to 1 F491 0 (Default Value) 9913 ...Repeated for IEC61850 GOOSE UInteger 2 9916 ...Repeated for IEC61850 GOOSE UInteger 3 9919 ...Repeated for IEC61850 GOOSE UInteger 4 B-44 M60 Motor Protection System GE Multilin...
Page 503 F500 9BB0 Teleprotection Input 1 States, one per register (16 items) 0 to 1 F108 0 (Off) 9BC0 Teleprotection Input 2 States, one per register (16 items) 0 to 1 F108 0 (Off) GE Multilin M60 Motor Protection System B-45...
Page 505 Digital Counter 1 Function 0 to 1 F102 0 (Disabled) A801 Digital Counter 1 Name F205 “Counter 1" A807 Digital Counter 1 Units F206 (none) A80A Digital Counter 1 Block 0 to 65535 F300 GE Multilin M60 Motor Protection System B-47...
Page 507 Repeated for IEC 61850 XSWI14 AEEB Repeated for IEC 61850 XSWI15 AEED Repeated for IEC 61850 XSWI16 AEEF Repeated for IEC 61850 XSWI17 AEF1 Repeated for IEC 61850 XSWI18 AEF3 Repeated for IEC 61850 XSWI19 GE Multilin M60 Motor Protection System B-49...
Page 508 IEC 61850 Standard GOOSE ID F209 “GOOSEOut” B064 IEC 61850 Standard GOOSE Destination MAC Address F072 B067 IEC 61850 GOOSE VLAN Transmit Priority 0 to 7 F001 B068 IEC 61850 GOOSE VLAN ID 0 to 4095 F001 B-50 M60 Motor Protection System GE Multilin...
Page 510 IEC 61850 Configurable GOOSE ID F209 “GOOSEOut_x_” B5C2 Configurable GOOSE Destination MAC Address F072 B5C5 IEC 61850 Configurable GOOSE VLAN Transmit Priority 0 to 7 F001 B5C6 IEC 61850 Configurable GOOSE VLAN ID 0 to 4095 F001 B-52 M60 Motor Protection System GE Multilin...
Page 517 Control Pushbutton 1 Function 0 to 1 F102 0 (Disabled) C761 Control Pushbutton 1 Events 0 to 1 F102 0 (Disabled) C762 ...Repeated for Control Pushbutton 2 C764 ...Repeated for Control Pushbutton 3 GE Multilin M60 Motor Protection System B-59...
Page 519 1 to 1000 F001 CAE0 Direct I/O Ch 1 Unreturned Messages Alarm Function 0 to 1 F102 0 (Disabled) CAE1 Direct I/O Ch 1 Unreturned Messages Alarm Msg Count 100 to 10000 F001 GE Multilin M60 Motor Protection System B-61...
Page 521 0 (Disabled) D2A2 Reserved (2 items) 0 to 1 F001 D2A4 ...Repeated for Remote Output 2 D2A8 ...Repeated for Remote Output 3 D2AC ...Repeated for Remote Output 4 D2B0 ...Repeated for Remote Output 5 GE Multilin M60 Motor Protection System B-63...
Page 522 IEC 61850 GGIO2.CF.SPCSO23.ctlModel Value 0 to 2 F001 D337 IEC 61850 GGIO2.CF.SPCSO24.ctlModel Value 0 to 2 F001 D338 IEC 61850 GGIO2.CF.SPCSO25.ctlModel Value 0 to 2 F001 D339 IEC 61850 GGIO2.CF.SPCSO26.ctlModel Value 0 to 2 F001 B-64 M60 Motor Protection System GE Multilin...
Page 524 FlexLogic™ Displays Active 0 to 1 F102 1 (Enabled) ED01 Reserved (6 items) F205 (none) ED07 Last Settings Change Date 0 to 4294967295 F050 ED09 Template Bitmask (750 items) 0 to 65535 F001 B-66 M60 Motor Protection System GE Multilin...
Page 525: Data Formats
POWER_FACTOR (SIGNED 16 BIT INTEGER) 0 = Time-Out, 1 = Acknowledge Positive values indicate lagging power factor; negative values indicate leading. F084 ENUMERATION: SELECTOR POWER UP 0 = Restore, 1 = Synchronize, 2 = Sync/Restore GE Multilin M60 Motor Protection System B-67...
Page 526 0 = 25%, 1 = 50%, 2 = 75%, 3 = 100% F111 ENUMERATION: UNDERVOLTAGE CURVE SHAPES F102 0 = Definite Time, 1 = Inverse Time ENUMERATION: DISABLED/ENABLED 0 = Disabled; 1 = Enabled B-68 M60 Motor Protection System GE Multilin...
Page 527 0 = 1 A, 1 = 5 A F124 ENUMERATION: LIST OF ELEMENTS bitmask element Phase Instantaneous Overcurrent 1 Phase Instantaneous Overcurrent 2 Phase Time Overcurrent 1 Phase Time Overcurrent 2 Neutral Instantaneous Overcurrent 1 GE Multilin M60 Motor Protection System B-69...
Page 528 Digital Element 14 FlexElement™ 2 Digital Element 15 FlexElement™ 3 Digital Element 16 FlexElement™ 4 Digital Element 17 FlexElement™ 5 Digital Element 18 FlexElement™ 6 Digital Element 19 FlexElement™ 7 Digital Element 20 B-70 M60 Motor Protection System GE Multilin...
Page 529 User-Programmable Pushbutton 16 RTD Input 12 Disconnect switch 1 RTD Input 13 Disconnect switch 2 RTD Input 14 Disconnect switch 3 RTD Input 15 Disconnect switch 4 RTD Input 16 Disconnect switch 5 GE Multilin M60 Motor Protection System B-71...
Page 530 Port 6 Offline RRTD Communications Failure Voltage Monitor F129 FlexLogic Error Token ENUMERATION: FLEXLOGIC TIMER TYPE Equipment Mismatch 0 = millisecond, 1 = second, 2 = minute Process Bus Failure Unit Not Programmed B-72 M60 Motor Protection System GE Multilin...
Page 531 A bit value of 0 = no error, 1 = error Unauthorized Access System Integrity Recovery System Integrity Recovery 06 F144 System Integrity Recovery 07 ENUMERATION: FORCED CONTACT INPUT STATE 0 = Disabled, 1 = Open, 2 = Closed GE Multilin M60 Motor Protection System B-73...
Page 532 0 = 52a, 1 = 52b, 2 = None F166 ENUMERATION: AUXILIARY VT CONNECTION TYPE 0 = Vn, 1 = Vag, 2 = Vbg, 3 = Vcg, 4 = Vab, 5 = Vbc, 6 = Vca B-74 M60 Motor Protection System GE Multilin...
Page 533 0 = A, 1 = B, 2 = C, 3 = G F175 ENUMERATION: PHASE LETTERS 0 = A, 1 = B, 2 = C F186 ENUMERATION: MEASUREMENT MODE 0 = Phase to Ground, 1 = Phase to Phase GE Multilin M60 Motor Protection System B-75...
Page 534 0 = Disabled, 1 = Enabled, 2 = Custom ENUMERATION: TEST ENUMERATION 0 = Test Enumeration 0, 1 = Test Enumeration 1 F200 TEXT40: 40-CHARACTER ASCII TEXT 20 registers, 16 Bits: 1st Char MSB, 2nd Char. LSB B-76 M60 Motor Protection System GE Multilin...
Page 535 MMXU2.MX.A.phsB.cVal.ang.f MMXU1.MX.PPV.phsAB.cVal.mag.f MMXU2.MX.A.phsC.cVal.mag.f MMXU1.MX.PPV.phsAB.cVal.ang.f MMXU2.MX.A.phsC.cVal.ang.f MMXU1.MX.PPV.phsBC.cVal.mag.f MMXU2.MX.A.neut.cVal.mag.f MMXU1.MX.PPV.phsBC.cVal.ang.f MMXU2.MX.A.neut.cVal.ang.f MMXU1.MX.PPV.phsCA.cVal.mag.f MMXU2.MX.W.phsA.cVal.mag.f MMXU1.MX.PPV.phsCA.cVal.ang.f MMXU2.MX.W.phsB.cVal.mag.f MMXU1.MX.PhV.phsA.cVal.mag.f MMXU2.MX.W.phsC.cVal.mag.f MMXU1.MX.PhV.phsA.cVal.ang.f MMXU2.MX.VAr.phsA.cVal.mag.f MMXU1.MX.PhV.phsB.cVal.mag.f MMXU2.MX.VAr.phsB.cVal.mag.f MMXU1.MX.PhV.phsB.cVal.ang.f MMXU2.MX.VAr.phsC.cVal.mag.f MMXU1.MX.PhV.phsC.cVal.mag.f MMXU2.MX.VA.phsA.cVal.mag.f MMXU1.MX.PhV.phsC.cVal.ang.f MMXU2.MX.VA.phsB.cVal.mag.f MMXU1.MX.A.phsA.cVal.mag.f MMXU2.MX.VA.phsC.cVal.mag.f MMXU1.MX.A.phsA.cVal.ang.f MMXU2.MX.PF.phsA.cVal.mag.f MMXU1.MX.A.phsB.cVal.mag.f MMXU2.MX.PF.phsB.cVal.mag.f MMXU1.MX.A.phsB.cVal.ang.f MMXU2.MX.PF.phsC.cVal.mag.f GE Multilin M60 Motor Protection System B-77...
Page 536 MMXU5.MX.PhV.phsC.cVal.mag.f MMXU4.MX.TotW.mag.f MMXU5.MX.PhV.phsC.cVal.ang.f MMXU4.MX.TotVAr.mag.f MMXU5.MX.A.phsA.cVal.mag.f MMXU4.MX.TotVA.mag.f MMXU5.MX.A.phsA.cVal.ang.f MMXU4.MX.TotPF.mag.f MMXU5.MX.A.phsB.cVal.mag.f MMXU4.MX.Hz.mag.f MMXU5.MX.A.phsB.cVal.ang.f MMXU4.MX.PPV.phsAB.cVal.mag.f MMXU5.MX.A.phsC.cVal.mag.f MMXU4.MX.PPV.phsAB.cVal.ang.f MMXU5.MX.A.phsC.cVal.ang.f MMXU4.MX.PPV.phsBC.cVal.mag.f MMXU5.MX.A.neut.cVal.mag.f MMXU4.MX.PPV.phsBC.cVal.ang.f MMXU5.MX.A.neut.cVal.ang.f MMXU4.MX.PPV.phsCA.cVal.mag.f MMXU5.MX.W.phsA.cVal.mag.f MMXU4.MX.PPV.phsCA.cVal.ang.f MMXU5.MX.W.phsB.cVal.mag.f MMXU4.MX.PhV.phsA.cVal.mag.f MMXU5.MX.W.phsC.cVal.mag.f MMXU4.MX.PhV.phsA.cVal.ang.f MMXU5.MX.VAr.phsA.cVal.mag.f MMXU4.MX.PhV.phsB.cVal.mag.f MMXU5.MX.VAr.phsB.cVal.mag.f MMXU4.MX.PhV.phsB.cVal.ang.f MMXU5.MX.VAr.phsC.cVal.mag.f MMXU4.MX.PhV.phsC.cVal.mag.f MMXU5.MX.VA.phsA.cVal.mag.f B-78 M60 Motor Protection System GE Multilin...
Page 537 GGIO5.ST.UIntIn8.stVal MMXU6.MX.VA.phsB.cVal.mag.f GGIO5.ST.UIntIn9.q MMXU6.MX.VA.phsC.cVal.mag.f GGIO5.ST.UIntIn9.stVal MMXU6.MX.PF.phsA.cVal.mag.f GGIO5.ST.UIntIn10.q MMXU6.MX.PF.phsB.cVal.mag.f GGIO5.ST.UIntIn10.stVal MMXU6.MX.PF.phsC.cVal.mag.f GGIO5.ST.UIntIn11.q GGIO4.MX.AnIn1.mag.f GGIO5.ST.UIntIn11.stVal GGIO4.MX.AnIn2.mag.f GGIO5.ST.UIntIn12.q GGIO4.MX.AnIn3.mag.f GGIO5.ST.UIntIn12.stVal GGIO4.MX.AnIn4.mag.f GGIO5.ST.UIntIn13.q GGIO4.MX.AnIn5.mag.f GGIO5.ST.UIntIn13.stVal GGIO4.MX.AnIn6.mag.f GGIO5.ST.UIntIn14.q GGIO4.MX.AnIn7.mag.f GGIO5.ST.UIntIn14.stVal GGIO4.MX.AnIn8.mag.f GGIO5.ST.UIntIn15.q GGIO4.MX.AnIn9.mag.f GGIO5.ST.UIntIn15.stVal GGIO4.MX.AnIn10.mag.f GGIO5.ST.UIntIn16.q GGIO4.MX.AnIn11.mag.f GGIO5.ST.UIntIn16.stVal GE Multilin M60 Motor Protection System B-79...
Page 538 April GGIO3.MX.AnIn26.mag.f GGIO3.MX.AnIn27.mag.f June GGIO3.MX.AnIn28.mag.f July GGIO3.MX.AnIn29.mag.f August GGIO3.MX.AnIn30.mag.f September GGIO3.MX.AnIn31.mag.f October GGIO3.MX.AnIn32.mag.f November GGIO3.ST.IndPos1.stVal December GGIO3.ST.IndPos2.stVal GGIO3.ST.IndPos3.stVal F238 GGIO3.ST.IndPos4.stVal ENUMERATION: REAL TIME CLOCK DAY GGIO3.ST.IndPos5.stVal GGIO3.ST.UIntIn1.q value GGIO3.ST.UIntIn1.stVal Sunday GGIO3.ST.UIntIn2.q Monday GGIO3.ST.UIntIn2.stVal B-80 M60 Motor Protection System GE Multilin...
Page 539 ENUMERATION: BRICK TRANSDUCER RANGE U6/AC4 U6/AC8 Value Description U7/AC5 -5...5V U7/AC8 -1...1mA U8/AC5 0...1mA U8/AC8 0...-1mA 0...5mA F253 0...10mA ENUMERATION: BRICK TRANSDUCER ORIGIN 0...20mA 4...20mA Value Description potentiometer None tap position U1/DC1 U1/DC2 U1/DC3 U2/DC1 GE Multilin M60 Motor Protection System B-81...
Page 540 17 to 32 (if required). The third register indicates [3] CONTACT INPUTS OFF (1 to 96) input/output state with bits 0 to 15 corresponding to input/output [4] VIRTUAL INPUTS (1 to 32) B-82 M60 Motor Protection System GE Multilin...
Page 541 0 = –1 to 1 mA, 1 = 0 to 1 mA, 2 = 4 to 20 mA Escape User 3 User 5 Message User PB 1 User 6 Right User PB 2 User 7 F531 ENUMERATION: LANGUAGE 0 = English, 1 = French, 2 = Chinese, 3 = Russian GE Multilin M60 Motor Protection System B-83...
Page 542 ENUMERATION: REMOTE DOUBLE-POINT STATUS INPUT Enumeration Remote double-point status input F601 ENUMERATION: COM2 PORT USAGE None Remote input 1 Enumeration COM2 port usage Remote input 2 RS485 Remote input 3 RRTD ↓ ↓ GPM-F Remote input 64 B-84 M60 Motor Protection System GE Multilin...
Page 543 UR_UINT16: FLEXINTEGER PARAMETER This 16-bit value corresponds to the Modbus address of the Enumeration Configurable GOOSE retransmission scheme selected FlexInteger parameter. Only certain values may be used Heartbeat as FlexIntegers. Aggressive Medium Relaxed GE Multilin M60 Motor Protection System B-85...
Page 544 B.4 MEMORY MAPPING APPENDIX B B-86 M60 Motor Protection System GE Multilin...
Page 545: Iec 61850
The M60 relay supports IEC 61850 server services over both TCP/IP and TP4/CLNP (OSI) communication protocol stacks. The TP4/CLNP profile requires the M60 to have a network address or Network Service Access Point (NSAP) to establish a communication link. The TCP/IP profile requires the M60 to have an IP address to establish communications. These addresses are located in the ...
Page 546: Server Data Organization
C.2.2 GGIO1: DIGITAL STATUS VALUES The GGIO1 logical node is available in the M60 to provide access to as many 128 digital status points and associated time- stamps and quality flags. The data content must be configured before the data can be used. GGIO1 provides digital status points for access by clients.
Page 547: Mmxu: Analog Measured Values
C.2.6 MMXU: ANALOG MEASURED VALUES A limited number of measured analog values are available through the MMXU logical nodes. Each MMXU logical node provides data from a M60 current and voltage source. There is one MMXU available for each configurable source (programmed in the ...
Page 548 The protection elements listed above contain start (pickup) and operate flags. For example, the start flag for PIOC1 is PIOC1.ST.Str.general. The operate flag for PIOC1 is PIOC1.ST.Op.general. For the M60 protection elements, these flags take their values from the pickup and operate FlexLogic™ operands for the corresponding element.
Page 549: Server Features And Configuration
C.3.4 LOGICAL DEVICE NAME The logical device name is used to identify the IEC 61850 logical device that exists within the M60. This name is composed of two parts: the IED name setting and the logical device instance. The complete logical device name is the combination of the two character strings programmed in the settings.
Page 550: Logical Node Name Prefixes
A built-in TCP/IP connection timeout of two minutes is employed by the M60 to detect ‘dead’ connections. If there is no data traffic on a TCP connection for greater than two minutes, the connection will be aborted by the M60. This frees up the con- nection to be used by other clients.
Page 551: Generic Substation Event Services: Gsse And Goose
MAC address for GSSE messages. If GSSE DESTINATION MAC ADDRESS a valid multicast Ethernet MAC address is not entered (for example, 00 00 00 00 00 00), the M60 will use the source Ether- net MAC address as the destination, with the multicast bit set.
Page 552 The M60 has the ability of detecting if a data item in one of the GOOSE datasets is erroneously oscillating. This can be caused by events such as errors in logic programming, inputs improperly being asserted and de-asserted, or failed station components.
Page 553: Ethernet Mac Address For Gsse/Goose
REMOTE IN 1 ITEM item to remote input 1. Remote input 1 can now be used in FlexLogic™ equations or other settings. The M60 must be rebooted (control power removed and re-applied) before these settings take effect. The value of remote input 1 (Boolean on or off) in the receiving device will be determined by the GGIO1.ST.Ind1.stVal value in the sending device.
Page 554: Gsse Id And Goose Id Settings
GSSE and GOOSE messages must have multicast destination MAC addresses. By default, the M60 is configured to use an automated multicast MAC scheme. If the M60 destination MAC address setting is not a valid multicast address (that is, the least significant bit of the first byte is not set), the address used as the destina- tion MAC will be the same as the local MAC address, but with the multicast bit set.
Page 555: Iec 61850 Implementation Via Enervista Ur Setup
An ICD file is generated for the M60 by the EnerVista UR Setup software that describe the capabilities of the IED. The ICD file is then imported into a system configurator along with other ICD files for other IEDs (from GE or other ven- dors) for system configuration.
Page 556: Configuring Iec 61850 Settings
Transmission GOOSE dataset may be added or deleted, or prefixes of some logical nodes may be changed. While all new configurations will be mapped to the M60 settings file when importing an SCD file, all unchanged settings will preserve the same values in the new settings file.
Page 557: About Icd Files
Although configurable transmission GOOSE can also be created and altered by some third-party system con- figurators, we recommend configuring transmission GOOSE for GE Multilin IEDs before creating the ICD, and strictly within EnerVista UR Setup software or the front panel display (access through the Settings > Product Setup > Com- munications >...
Page 558 Furthermore, it defines the capabilities of an IED in terms of communication services offered and, together with its LNType, instantiated data (DO) and its default or configuration values. There should be only one IED section in an ICD since it only describes one IED. C-14 M60 Motor Protection System GE Multilin...
Page 559 RptEnabled Other ReportControl elements DOI (name) SDI (name) DAI (name) Text Other DOI elements SDI (name) DAI (name) Text Other LN elements Other LDevice elements 842797A1.CDR Figure 0–4: ICD FILE STRUCTURE, IED NODE GE Multilin M60 Motor Protection System C-15...
Page 560 BDA (name, bType, type) Other BDA elements Other BDA elements Other DAType elements Other DAType elements EnumType (id) Text EnumVal (ord) Other EnumVal elements Other EnumType elements 842798A1.CDR Figure 0–5: ICD FILE STRUCTURE, DATATYPETEMPLATES NODE C-16 M60 Motor Protection System GE Multilin...
Page 561: Creating An Icd File With Enervista Ur Setup
The EnerVista UR Setup will prompt to save the file. Select the file path and enter the name for the ICD file, then click OK to generate the file. The time to create an ICD file from the offline M60 settings file is typically much quicker than create an ICD file directly from the relay.
Page 562 Like ICD files, the Header node identifies the SCD file and its version, and specifies options for the mapping of names to signals. The Substation node describes the substation parameters: Substation PowerSystemResource EquipmentContainer Power Transformer GeneralEquipment EquipmentContainer VoltageLevel Voltage PowerSystemResource Function SubFunction GeneralEquipment 842792A1.CDR Figure 0–7: SCD FILE STRUCTURE, SUBSTATION NODE C-18 M60 Motor Protection System GE Multilin...
Page 563 IdInst is the instance identification of the logical device within the IED on which the control block is located, and cbName is the name of the control block. GE Multilin M60 Motor Protection System C-19...
Page 564: Importing An Scd File With Enervista Ur Setup
Figure 0–9: SCD FILE STRUCTURE, IED NODE C.5.6 IMPORTING AN SCD FILE WITH ENERVISTA UR SETUP The following procedure describes how to update the M60 with the new configuration from an SCD file with the EnerVista UR Setup software. Right-click anywhere in the files panel and select the Import Contents From SCD File item.
Page 565 The software will open the SCD file and then prompt the user to save a UR-series settings file. Select a location and name for the URS (UR-series relay settings) file. If there is more than one GE Multilin IED defined in the SCD file, the software prompt the user to save a UR-series set- tings file for each IED.
Page 566: Acsi Conformance
Setting group control REPORTING Buffered report control M7-1 sequence-number M7-2 report-time-stamp M7-3 reason-for-inclusion M7-4 data-set-name M7-5 data-reference M7-6 buffer-overflow M7-7 entryID M7-8 BufTm M7-9 IntgPd M7-10 Unbuffered report control M8-1 sequence-number M8-2 report-time-stamp M8-3 reason-for-inclusion C-22 M60 Motor Protection System GE Multilin...
Page 567: Acsi Services Conformance Statement
SERVER/ UR FAMILY PUBLISHER SERVER (CLAUSE 6) ServerDirectory APPLICATION ASSOCIATION (CLAUSE 7) Associate Abort Release LOGICAL DEVICE (CLAUSE 8) LogicalDeviceDirectory LOGICAL NODE (CLAUSE 9) LogicalNodeDirectory GetAllDataValues DATA (CLAUSE 10) GetDataValues SetDataValues GetDataDirectory GetDataDefinition GE Multilin M60 Motor Protection System C-23...
Page 568 (qchg) S27-3 data-update (dupd) GetURCBValues SetURCBValues LOGGING (CLAUSE 14) LOG CONTROL BLOCK GetLCBValues SetLCBValues QueryLogByTime QueryLogByEntry GetLogStatusValues GENERIC SUBSTATION EVENT MODEL (GSE) (CLAUSE 14.3.5.3.4) GOOSE-CONTROL-BLOCK SendGOOSEMessage GetReference GetGOOSEElementNumber GetGoCBValues SetGoCBValues GSSE-CONTROL-BLOCK SendGSSEMessage GetReference C-24 M60 Motor Protection System GE Multilin...
Page 569 (QueryLogByTime or QueryLogAfter) NOTE c8: shall declare support for at least one (SendGOOSEMessage or SendGSSEMessage) c9: shall declare support if TP association is available c10: shall declare support for at least one (SendMSVMessage or SendUSVMessage) GE Multilin M60 Motor Protection System C-25...
Page 570: Logical Nodes
RDRE: Disturbance recorder function RADR: Disturbance recorder channel analogue RBDR: Disturbance recorder channel binary RDRS: Disturbance record handling RBRF: Breaker failure RDIR: Directional element RFLO: Fault locator RPSB: Power swing detection/blocking RREC: Autoreclosing C-26 M60 Motor Protection System GE Multilin...
Page 571 T: LOGICAL NODES FOR INSTRUMENT TRANSFORMERS TCTR: Current transformer TVTR: Voltage transformer Y: LOGICAL NODES FOR POWER TRANSFORMERS YEFN: Earth fault neutralizer (Peterson coil) YLTC: Tap changer YPSH: Power shunt YPTR: Power transformer GE Multilin M60 Motor Protection System C-27...
Page 572 ZCON: Converter ZGEN: Generator ZGIL: Gas insulated line ZLIN: Power overhead line ZMOT: Motor ZREA: Reactor ZRRC: Rotating reactive component ZSAR: Surge arrestor ZTCF: Thyristor controlled frequency converter ZTRC: Thyristor controlled reactive component C-28 M60 Motor Protection System GE Multilin...
Page 573: Iec 60870-5-104 Protocol
Balanced Transmision Not Present (Balanced Transmission Only)   Unbalanced Transmission One Octet  Two Octets  Structured  Unstructured Frame Length (maximum length, number of octets): Not selectable in companion IEC 60870-5-104 standard GE Multilin M60 Motor Protection System...
Page 574  <18> := Packed start events of protection equipment with time tag M_EP_TB_1  <19> := Packed output circuit information of protection equipment with time tag M_EP_TC_1  <20> := Packed single-point information with status change detection M_SP_NA_1 M60 Motor Protection System GE Multilin...
Page 575  <103> := Clock synchronization command (see Clause 7.6 in standard) C_CS_NA_1  <104> := Test command C_TS_NA_1  <105> := Reset process command C_RP_NA_1  <106> := Delay acquisition command C_CD_NA_1  <107> := Test command with time tag CP56Time2a C_TS_TA_1 GE Multilin M60 Motor Protection System...
Page 576 •Blank boxes indicate functions or ASDU not used. •‘X’ if only used in the standard direction TYPE IDENTIFICATION CAUSE OF TRANSMISSION MNEMONIC <1> M_SP_NA_1 <2> M_SP_TA_1 <3> M_DP_NA_1 <4> M_DP_TA_1 <5> M_ST_NA_1 <6> M_ST_TA_1 <7> M_BO_NA_1 <8> M_BO_TA_1 <9> M_ME_NA_1 M60 Motor Protection System GE Multilin...
Page 577 <34> M_ME_TD_1 <35> M_ME_TE_1 <36> M_ME_TF_1 <37> M_IT_TB_1 <38> M_EP_TD_1 <39> M_EP_TE_1 <40> M_EP_TF_1 <45> C_SC_NA_1 <46> C_DC_NA_1 <47> C_RC_NA_1 <48> C_SE_NA_1 <49> C_SE_NB_1 <50> C_SE_NC_1 <51> C_BO_NA_1 <58> C_SC_TA_1 <59> C_DC_TA_1 <60> C_RC_TA_1 GE Multilin M60 Motor Protection System...
Page 578 <120> F_FR_NA_1 <121> F_SR_NA_1 <122> F_SC_NA_1 <123> F_LS_NA_1 <124> F_AF_NA_1 <125> F_SG_NA_1 <126> F_DR_TA_1*) BASIC APPLICATION FUNCTIONS Station Initialization:  Remote initialization Cyclic Data Transmission:  Cyclic data transmission Read Procedure:  Read procedure M60 Motor Protection System GE Multilin...
Page 579  Mode B: Local freeze with counter interrogation  Mode C: Freeze and transmit by counter-interrogation commands  Mode D: Freeze by counter-interrogation command, frozen values reported simultaneously  Counter read  Counter freeze without reset GE Multilin M60 Motor Protection System...
Page 580 Maximum number of outstanding I-format APDUs k and latest acknowledge APDUs (w): PARAMETER DEFAULT REMARKS SELECTED VALUE VALUE 12 APDUs Maximum difference receive sequence number to send state variable 12 APDUs 8 APDUs 8 APDUs Latest acknowledge after receiving I-format APDUs M60 Motor Protection System GE Multilin...
Page 581: Point List
D.1.2 POINT LIST The IEC 60870-5-104 data points are configured through the    SETTINGS PRODUCT SETUP COMMUNICATIONS DNP / menu. Refer to the Communications section of Chapter 5 for additional details. IEC104 POINT LISTS GE Multilin M60 Motor Protection System...
Page 582 D.1 IEC 60870-5-104 PROTOCOL APPENDIX D D-10 M60 Motor Protection System GE Multilin...
Page 583: Device Profile Document
2048 Maximum Data Link Re-tries: Maximum Application Layer Re-tries:  None  None  Fixed at 3  Configurable  Configurable Requires Data Link Layer Confirmation:  Never  Always  Sometimes  Configurable GE Multilin M60 Motor Protection System...
Page 584 FlexLogic™. The On/Off times and Count value are ignored. “Pulse Off” and “Latch Off” operations put the appropriate Virtual Input into the “Off” state. “Trip” and “Close” operations both put the appropriate Virtual Input into the “On” state. M60 Motor Protection System GE Multilin...
Page 585  16 Bits (Counter 8) Default Variation: 1  32 Bits (Counters 0 to 7, 9)  Point-by-point list attached  Other Value: _____  Point-by-point list attached Sends Multi-Fragment Responses:  Yes  No GE Multilin M60 Motor Protection System...
Page 586: E.1.2 Implementation Table
Otherwise, static object requests sent with qualifiers 00, 01, 06, 07, or 08, will be responded with qualifiers 00 or 01 (for change- event objects, qualifiers 17 or 28 are always responded.) Note 3: Cold restarts are implemented the same as warm restarts – the M60 is not restarted, but the DNP process is restarted. M60 Motor Protection System GE Multilin...
Page 587 Otherwise, static object requests sent with qualifiers 00, 01, 06, 07, or 08, will be responded with qualifiers 00 or 01 (for change- event objects, qualifiers 17 or 28 are always responded.) Note 3: Cold restarts are implemented the same as warm restarts – the M60 is not restarted, but the DNP process is restarted. GE Multilin M60 Motor Protection System...
Page 588 Otherwise, static object requests sent with qualifiers 00, 01, 06, 07, or 08, will be responded with qualifiers 00 or 01 (for change- event objects, qualifiers 17 or 28 are always responded.) Note 3: Cold restarts are implemented the same as warm restarts – the M60 is not restarted, but the DNP process is restarted. M60 Motor Protection System GE Multilin...
Page 589 Otherwise, static object requests sent with qualifiers 00, 01, 06, 07, or 08, will be responded with qualifiers 00 or 01 (for change- event objects, qualifiers 17 or 28 are always responded.) Note 3: Cold restarts are implemented the same as warm restarts – the M60 is not restarted, but the DNP process is restarted. GE Multilin M60 Motor Protection System...
Page 590: Dnp Point Lists
Change Event Variation reported when variation 0 requested: 2 (Binary Input Change with Time), Configurable Change Event Scan Rate: 8 times per power system cycle Change Event Buffer Size: 500 Default Class for All Points: 1 M60 Motor Protection System GE Multilin...
Page 591: Binary And Control Relay Output
Virtual Input 27 Virtual Input 59 Virtual Input 28 Virtual Input 60 Virtual Input 29 Virtual Input 61 Virtual Input 30 Virtual Input 62 Virtual Input 31 Virtual Input 63 Virtual Input 32 Virtual Input 64 GE Multilin M60 Motor Protection System...
Page 592: Counters
Events Since Last Clear A counter freeze command has no meaning for counters 8 and 9. M60 Digital Counter values are represented as 32-bit integers. The DNP 3.0 protocol defines counters to be unsigned integers. Care should be taken when interpreting negative counter values.
Page 593: Analog Inputs
Change Event Variation reported when variation 0 requested: 1 (Analog Change Event without Time) Change Event Scan Rate: defaults to 500 ms Change Event Buffer Size: 256 Default Class for all Points: 2 GE Multilin M60 Motor Protection System E-11...
Page 594 E.2 DNP POINT LISTS APPENDIX E E-12 M60 Motor Protection System GE Multilin...
Page 595: Revision History
12 March 2008 URX-260 1601-0108-T1 5.6x 27 June 2008 08-0390 1601-0109-U1 5.7x 29 May 2009 09-0938 1601-0109-U2 5.7x 30 September 2009 09-1165 1601-0109-V1 5.8x 29 May 2010 09-1457 1601-0109-V2 5.8x 30 September 2017 17-4032 GE Multilin M60 Motor Protection System...
Page 596: Changes To The M60 Manual
5-167 Update Updated BREAKER FAILURE section Update Updated MODBUS MEMORY MAP section Update Updated PROTECTION AND OTHER LOGICAL NODES section Table F–4: MAJOR UPDATES FOR M60 MANUAL REVISION U2 (Sheet 1 of 2) PAGE PAGE CHANGE DESCRIPTION (U1) (U2) Title...
Page 597 APPENDIX F F.1 CHANGE NOTES Table F–4: MAJOR UPDATES FOR M60 MANUAL REVISION U2 (Sheet 2 of 2) PAGE PAGE CHANGE DESCRIPTION (U1) (U2) 4-14 4-14 Update Updated LED INDICATORS section 5-22 5-22 Update Updated IEC 61850 PROTOCOL section 5-77...
Page 598 F.1 CHANGE NOTES APPENDIX F Table F–5: MAJOR UPDATES FOR M60 MANUAL REVISION U1 (Sheet 2 of 2) PAGE PAGE CHANGE DESCRIPTION (T1) (U1) Update Updated CLEAR RECORDS section Update Updated RELAY MAINTENANCE section Update Updated MINOR SELF-TEST ERRORS section...
Page 599 APPENDIX F F.1 CHANGE NOTES Table F–8: MAJOR UPDATES FOR M60 MANUAL REVISION S2 PAGE PAGE CHANGE DESCRIPTION (S1) (S2) Title Title Update Manual part number to 1601-0108-S2 3-40 3-40 Update Updated MANAGED ETHERNET SWITCH OVERVIEW section 3-40 3-40 Update...
Page 600: Abbreviations
MVA ....MegaVolt-Ampere (total 3-phase) FDH....Fault Detector high-set MVA_A ... MegaVolt-Ampere (phase A) FDL ....Fault Detector low-set MVA_B ... MegaVolt-Ampere (phase B) FLA....Full Load Current MVA_C... MegaVolt-Ampere (phase C) FO ....Fiber Optic M60 Motor Protection System GE Multilin...
Page 601: M60 Motor Protection System
RSTR ..... Restrained WRT....With Respect To RTD....Resistance Temperature Detector RTU....Remote Terminal Unit X .....Reactance RX (Rx) ..Receive, Receiver XDUCER..Transducer XFMR....Transformer s ..... second S..... Sensitive Z......Impedance, Zone SAT ....CT Saturation GE Multilin M60 Motor Protection System...
Page 602: F.3.1 Ge Multilin Warranty
F.3.1 GE MULTILIN WARRANTY For products shipped as of 1 October 2013, GE Grid Solutions warrants most of its GE manufactured products for 10 years. For warranty details including any limitations and disclaimers, see the GE Grid Solutions Terms and Conditions at https://www.gegridsolutions.com/multilin/warranty.htm...
Page 603 IEC 61850 ..............5-223 BLOCK DIAGRAM .............. 1-4 inter-relay communications ..........2-19 BLOCK SETTING ............... 5-5 Modbus ..........5-17, 5-39, B-1, B-3 BREAKER CONTROL Modbus registers ............B-21 control of 2 breakers ............4-24 GE Multilin M60 Motor Protection System...
Page 606 RTD inputs ............2-15, 3-26 virtual ................5-219 INSPECTION CHECKLIST ..........1-2 G.703 ............ 3-36, 3-37, 3-38, 3-41 INSTALLATION GE TYPE IAC CURVES ..........5-164 communications .............3-28 GROUND CURRENT METERING ........6-17 CT inputs .............. 3-12, 3-13 GROUND IOC RS485 ................3-29 FlexLogic™...
Page 607 OPERATING TEMPERATURE .......... 2-20 withdrawal ..............3-6, 3-7 OPERATING TIMES ............2-10 MONITORING ELEMENTS ..........5-207 ORDER CODES ......2-4, 2-5, 2-6, 2-7, 6-27, 7-3 MOTOR ORDER CODES, UPDATING ..........7-3 actual values ............6-3, 6-15 GE Multilin M60 Motor Protection System...
Page 608 Modbus registers ............B-23 PER-UNIT QUANTITY ............5-4 settings ................5-39 PHASE ANGLE METERING ..........6-13 REAR TERMINAL ASSIGNMENTS ........3-8 PHASE CURRENT METERING ......... 6-16 RECLOSER CURVES ..........5-85, 5-165 PHASE DIRECTIONAL OC REDUCED VOLTAGE STARTING M60 Motor Protection System GE Multilin...
Page 609 RTD BIAS ............5-113, 5-121 SOFTWARE, PC RTD INPUTS see entry for EnerVista UR Setup actual values ..............6-22 SOURCE FREQUENCY ............ 6-19 Modbus registers ..........B-16, B-27 SOURCE TRANSFER SCHEMES ........5-177 settings ............. 5-236, 5-239 SOURCES GE Multilin M60 Motor Protection System...
Page 610 UNDERVOLTAGE CHARACTERISTICS ......5-177 Modbus registers ..........B-32, B-36 UNEXPECTED RESTART ERROR ........7-8 settings ............... 5-113 UNIT NOT PROGRAMMED ........5-66, 7-5 specifications..............2-10 UNPACKING THE RELAY ..........1-2 TIME ................. 7-2 UNRETURNED MESSAGES ALARM .........5-64 viii M60 Motor Protection System GE Multilin...
Page 611 WEB SERVER PROTOCOL ..........5-34 WEBSITE ................1-2 VAR-HOURS ............2-14, 6-19 VIBRATION TESTING ............2-21 VIRTUAL INPUTS actual values ..............6-4 commands ..............7-1 ZERO SEQUENCE CORE BALANCE ........ 3-13 FlexLogic™ operands ............ 5-97 GE Multilin M60 Motor Protection System...
Page 612 INDEX M60 Motor Protection System GE Multilin...

GE M60 Instruction Manual

1 Getting Started

2 Product Description

3 Hardware

4 Human Interfaces

5 Settings

7 Commands and

8 Security

9 Theory of Operation

10 Commissioning

Parameter Lists

Modbus Function Codes

File Transfers

Memory Mapping

Iec 61850

Overview

Server Data Organization

Server Features and Configuration

Quick Links

Related Manuals for GE M60

Summary of Contents for GE M60