Direct Inputs And Outputs - GE C60 Instruction Manual

INPUTS/OUTPUTS
5.9.5.2 Graphical front panel
SETTINGS  INPUTS/OUTPUTS  RESETTING
 RESETTING

Some events can be programmed to latch the front panel LED event indicators, target messages, and/or graphical front
panel annunciator windows. Once set, the latching mechanism holds the latched indicators, messages, or windows in the
set state after the initiating condition has cleared until a
FlexLogic latches) to the reset state where the initiating condition has cleared. The
front panel RESET button, a remote device via a communications channel, or any selected operand. The Modbus execute
function 05h with operation code 1 command is also available to perform the same function as the front panel RESET key.
— The three sources of
RESET OPERAND
source of a command also activates its individual operand
RESET
identify the source of the command. Each of these three operands generates an event in the event record when activated.
The
RESET OPERAND
RESET ANNUNCIATOR
windows on the graphical front panel. The other methods to acknowledge/reset annunciator windows include:
• On the displayed page, press the RESET pushbutton with none of the annunciator windows selected to acknowledge/
reset all annunciator windows on that page
• To acknowledge/reset a specific annunciator window, use the Up, Down, Left and Right pushbuttons to select the
window, and press the RESET or ENTER pushbutton
5
• All annunciator windows can be reset remotely by programming a Virtual Input (for example Virtual Input 1) as the
input to the
RESET ANNUNCIATOR
(or function 10h with address 400h) is used to set the state of Virtual Input 1.
For the
RESET ANNUNCIATOR
command, operand source and manual source. Each individual source of a
its individual operand
operands generates an event in the event record when activated. The setting here selects the operand that activates the
RESET ANCTR OP (OPRD)
activates the
RESET ANCTR OP (MNUL)

5.9.6 Direct inputs and outputs

5.9.6.1 Direct inputs
SETTINGS  INPUTS/OUTPUTS  DIRECT INPUTS  DIRECT INPUT 1(32)
 DIRECT INPUT 1

These settings specify how the direct input information is processed.
DIRECT INPUT 1 NAME
5-314
RESET OPERAND:

Off
RESET ANNUNCIATOR:

Off
commands each activates the
RESET
setting here selects the operand that activates the
— Used to select a FlexLogic operand that when activated acknowledges/resets all annunciator
setting. Then the Modbus execute function 05h with operation code 1000h command
setting, the
RESET ANCTR OP
or
RESET OP (OPRD) RESET ANCTR OP (MNUL)
operand. The RESET pushbutton on the front panel or the reset command from the software
operand.
DIRECT INPUT 1

NAME: Dir Ip 1
DIRECT INPUT 1

DEVICE ID: 0
DIRECT INPUT 1

BIT NUMBER:
DIRECT INPUT 1

DEFAULT: Off
DIRECT INPUT 1

EVENTS: Disabled
— This setting allows the user to assign a descriptive name to the direct input.
Range: FlexLogic operand
Range: FlexLogic operand
command is received to return these latches (not including
RESET
RESET
FlexLogic operand. Each individual
RESET OP
,
RESET OP (PUSHBUTTON)
RESET OP (OPERAND)
FlexLogic operand is activated by the two sources of
RESET ANNUNCIATOR
to identify the source of the command. Each of these two
Range: up to 12 alphanumeric characters
Range: 0 to 16
Range: 0 to 32
0
Range: On, Off, Latest/On, Latest/Off
Range: Enabled, Disabled
C60 BREAKER PROTECTION SYSTEM – INSTRUCTION MANUAL
CHAPTER 5: SETTINGS
command can be sent from the
, or
RESET OP (COMMS) RESET OP (OPERAND)
operand.
RESET
command also activates
to