Quadra-Fire FOGATAGRANDE FG21SP-LP Owner's Manual
Quadra-Fire FOGATAGRANDE FG21SP-LP Owner's Manual

Quadra-Fire FOGATAGRANDE FG21SP-LP Owner's Manual

Decorative gas log set for use with the fogata grande only
Hide thumbs Also See for FOGATAGRANDE FG21SP-LP:

Advertisement

Models:
FG21SP-NG
FG21SP-LP
Decorative Gas Log Set
For Use With The Fogata
Grande only
• Important operating and
maintenance instructions
included.
WARNING
If the information in these
instructions is not followed
exactly, a fire or explosion may
result causing property damage,
personal injury, or death.
• Do not store or use gasoline or other flam-
mable vapors and liquids in the vicinity of
this or any other appliance.
• What to do if you smell gas:
- Do not try to light any appliance.
- Do not touch any electrical switch. Do not
use any phone in your building.
- Immediately call your gas supplier from
a neighbor's phone. Follow the gas
supplier's instructions.
- If you cannot reach your gas supplier, call
the fire department.
• Installation and service must be performed
by a qualified installer, service agency, or
the gas supplier.
• For Outdoor Use Only.

CAUTION
DO NOT DISCARD THIS MANUAL
Read, understand and follow
these instructions for safe
installation and operation.
• Keep children away.
• Keep children away.
• Keep children away.
• CAREFULLY SUPERVISE children around the firepit.
• CAREFULLY SUPERVISE children around the firepit.
• CAREFULLY SUPERVISE children around the firepit.
• Alert children and adults to hazards of high
• Alert children and adults to hazards of high
• Alert children and adults to hazards of high
• Keep clothing, furniture, draperies and other
• Keep clothing, furniture, draperies and other
• Keep clothing, furniture, draperies and other
Improper installation, adjustment, alteration, service or
maintenance can cause injury or property damage. Read
the installation, operating and maintenance instructions
thoroughly before installing or servicing this equipment.
Quadra-Fire • Fogata Grande
Owner's Manual
Installation and Operation
Leave this manual with
party responsible for
use and operation.
WARNING
WARNING
WARNING
HOT! DO NOT TOUCH.
HOT! DO NOT TOUCH.
HOT! DO NOT TOUCH.
SEVERE BURNS MAY RESULT.
SEVERE BURNS MAY RESULT.
SEVERE BURNS MAY RESULT.
CLOTHING IGNITION MAY RESULT.
CLOTHING IGNITION MAY RESULT.
CLOTHING IGNITION MAY RESULT.
Cast iron and other surfaces are hot during
Cast iron and other surfaces are hot during
Cast iron and other surfaces are hot during
operation and cool down.
operation and cool down.
operation and cool down.
temperatures.
temperatures.
temperatures.
combustibles away.
combustibles away.
combustibles away.
WARNING
Installation and service of this appliance should be performed
by qualified personnel. Hearth & Home Technologies
suggests NFI certified or factory-trained
professionals, or technicians supervised
by an NFI certified professional.
October 2006

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the FOGATAGRANDE FG21SP-LP and is the answer not in the manual?

Questions and answers

Summary of Contents for Quadra-Fire FOGATAGRANDE FG21SP-LP

  • Page 1 Installation and service of this appliance should be performed by qualified personnel. Hearth & Home Technologies suggests NFI certified or factory-trained professionals, or technicians supervised by an NFI certified professional. Quadra-Fire • Fogata Grande October 2006 Owner’s Manual Installation and Operation Leave this manual with party responsible for use and operation.
  • Page 2 The information contained in this owner’s manual, unless noted otherwise, applies to all models and gas control systems. Your new Fogata Grande will give you years of durable use and trouble-free enjoyment. Welcome to the Quadra-Fire family of appliance products! We recommend that you record the following pertinent information about your appliance: Date purchased/installed:...
  • Page 3: Table Of Contents

    B. Logs ........8 C. Limited Lifetime Warranty ..... 20 Quadra-Fire • Fogata Grande October 2006 .
  • Page 4: Listing And Code Approvals

    CSA International Requirement 4.96 U.S. for Outdoor Gas Fireplaces, 2004 for the U.S. and Canada and has been listed by OMNI-Test Laboratories, Inc. for installation and operation as described in these installation and operat- ing instructions. The installation must conform with local codes or, in the ab- sence of local codes, with the National Fuel Gas Code ANSI Z223.1 or CSA B149.1, Natural Gas and Propane Installa- tion Code. B. BTU Specifications FG2SP-NG FG2SP-LP Quadra-Fire • Fogata Grande October 2006 Max Input Model BTUH Orifice Size 180,000 19/64 180,000...
  • Page 5: Getting Started

    • Consult insurance carrier, local building, fire officials or authorities having jurisdiction about restrictions, installation inspection, and permits. Asphyxiation Risk • This gas log set is for outdoor use in a well- ventilated space. • Log set must not be installed inside an enclosed structure or unvented appliance. Sharp Edges • Wear protective gloves and safety glasses during installation. Quadra-Fire • Fogata Grande October 2006 WARNING CAUTION WARNING CAUTION...
  • Page 6: Inspect The Appliance And Components

    Report damaged parts to dealer. Valve Control Box Assembly • Carefully remove the appliance and components from the packaging • The gas logs may be packaged separately and must be field installed. • Report to your dealer any parts damaged in shipment. • Read all of the instructions before starting the installation. Follow these instructions carefully during the installation to ensure maximum safety and benefit. Quadra-Fire • Fogata Grande October 2006 Burner Assembly...
  • Page 7: Framing And Clearances

    A. Select Appliance Location When selecting a location for your appliance it is important to consider the required clearances to all combustibles. B. Clearances Place the Fogata Grande on a flat stable surface. The clear- ance requirements to any combustible material, to any side, is a minimum of 24 inches. Combustible materials are not allowed over the top of the Fogata Grande. 10’ 10’ Non-combustible Non-combustible Fire Risk Provide adequate clearance: • Around air openings. • For service access. Locate appliance away from traffic areas. 10’ 10’ Quadra-Fire • Fogata Grande October 2006 WARNING...
  • Page 8: Appliance Setup

    In the event that the Pilot assembly is not installed, locate the cross section of the burner with the colored highlight. (this will be on the inner ring at the cross section. Note the port-holes will be facing down). Insert the Pilot hood bracket over the burner tube and slide it forward so the top front clip slides over the tube of the burner and covers the highlighted markings on the burner tube. In order to assemble the unit, the Pilot hood bracket may need to be inserted at an angle and twisted into place to ensure that the unit is in its proper position. 5) Place the stainless steel grate (heavy round bar grate, supplied with fire pit) in position in the lower part of the bowl. This grate will rest on top of the lower tabs. Next place the screen over the grate so that the oval open- ing in the screen lines up with the direction of the stainless bars on the grate as shown in Figure 4. Feed the burner flex line, pilot tube and piezo ignitor wire down through the center of the screen and grate and through the oval hole in the side of the bowl The burner will rest flat on the inside of the bowl. Quadra-Fire • Fogata Grande October 2006 Figure 4...
  • Page 9 6) With the valve control box under the edge of the bowl, connect the pilot tube to the top of the valve in the control box. The stainless steel flex connector is to be connected to the brass elbow located on the top of the valve control box. The piezo ignitor lead is to be connected to the ignitor lead coming out of the valve control box. Thermopile Figure 5 7) Feed the thermopile up through the oval hole in the bowl and insert it into the open hole in the pilot assembly. Ensure that the thermopile snaps into place and is securly in posi- tion to ensure proper connection. 8) Replace leg “A” under the Fogata Grande bowl and se- cure the valve control box on the two screws previously in- stalled in step 3 9) With all the gas componets now securly in place, take the lava rock supplied and spread it over the screen so that it covers the sides of the burner but ensure it does not cover the top of the burner in order to ensure proper flame 10) Log Instalation and placement instructions for the log set are provided with the log set Quadra-Fire • Fogata Grande October 2006...
  • Page 10: Gas Information

    • Gas Line Pressure Test: Perform pressure test according to state and local code (if pressure exceeds 1/2 in. psi [3.5 kPa]) before appliance is connected. Be sure to release air pressure from the gas line before connection is made to the appliance. Excessive pressure will damage the gas control and may cause a gas leak. • Gas Leak Test: Make sure the gas connections are tight. Turn on the gas and coat each joint with a non-corrosive gas leak check solution. Air bubbles will form indicating any leaks. DO NOT USE A FLAME OR ANY TYPE OF IGNITION SOURCE TO CHECK FOR LEAKS. All leaks must be corrected before proceeding with installation. Quadra-Fire • Fogata Grande October 2006 WARNING CHECK FOR GAS LEAKS Fire Risk Explosion Risk Asphyxiation Risk • Check all fittings and connections. • Do not use open flame. • After the gas line installation is complete, all connections must be tightened and checked for leaks with a commercially available, non-corrosive leak check solution. Be sure to rinse off all leak check...
  • Page 11: Gas Connection

    D. High Altitude Installations OMNI gas appliances are tested and approved without re- quiring changes for elevations from 0 to 2000 ft in the USA and Canada. When installing this appliance at an elevation above 2000 ft, it may be necessary to decrease the input rating by chang- ing the existing burner orifice to a smaller size. Input rate should be reduced by 4% for each 1000 ft above a 2000 ft elevation in the U.S.A., or 10% for elevations between 2000 and 4500 ft in Canada. If the heating value of the gas has been reduced, these rules do not apply. To identify the prop- er orifice size, check with the local gas utility. If installing this appliance at an elevation above 4500 ft (in Canada), check with local authorities. Quadra-Fire • Fogata Grande October 2006 WARNING all connections must be tightened and checked for leaks with a commercially available, non-corrosive leak check solution. Be sure to rinse off all leak check solution following testing.
  • Page 12: Operating Instructions

    CLOTHING IGNITION MAY RESULT Glass and other surfaces are hot during operation and cool down. • Keep children away. • CAREFULLY SUPERVISE children in same room as appliance. • Alert children and adults to hazards of high temperatures. • Keep clothing, furniture, draperies and other combustibles away. Piezo On/Off Switch Quadra-Fire • Fogata Grande October 2006 WARNING WARNING...
  • Page 13: Lighting Instructions

    • If the pilot will not stay lit after several tries, turn the gas control handle to “OFF” and call your service technician or gas supplier. • LIGHTING PILOT WITH OPTIONAL PIEZO LIGHTER 1. Follow steps 1 thru 5 above. 2. Push the control handle in and at the same time press the push-button ignitor several times. This should cause a spark at the pilot burner and ignite the pilot 3. Once the pilot lights, continue to depress the control handle for one (1) minute 4. After one minute, release control handle and the pilot should remain lit 5. If the pilot does not remain lit, rotate control handle to “OFF” position (Fig. 9) 6. Wait five (%) minutes and repeat above steps 10. Turn control handle counterclockwise  to “ON” 11. Place toggle switch in the “ON” position (Fig. 9) Turn control handle clockwise  to the “OFF” position. Do not force PILOT LIGHTING INSTRUCTIONS MILLIVOLT VALVE TO TURN OFF GAS TO APPLIANCE Fig. 9 Quadra-Fire • Fogata Grande Pilot Thermopile Fig. 10 Millivolt October 2006...
  • Page 14: After The Appliance Is Lit

    • Keep furniture, draperies away from appliance. Fire Risk Keep combustible materials, gasoline and other flammable vapors and liquids clear of appliance. • Do NOT store flammable materials in the • Do NOT use gasoline, lantern fuel, Combustible materials may ignite. C. Inspection Before Each Use Before each use of the appliance, check to be sure that the logs are in proper locations and that the burner is not ob- structed with any foreign or combustible materials. Check that the burner and all air passageways are kept clean. If any part of the burner is not igniting properly, turn off the appliance. Let it cool, and check for any obstructions. Quadra-Fire • Fogata Grande October 2006 WARNING vicinity of the appliance. kerosene, charcoal lighter fluid or similar liquids in this appliance.
  • Page 15: Troubleshooting

    C. The valve knob is in the 1. Turn the valve knob to the “PILOT” position and “OFF” position. depress. Keep the match near the pilot burner until it lights. D. The pilot orifice is plugged, 1. This repair requires tools and some degree of not allowing gas to flow. experience. Call a qualified service technician. E. There is no gas supply to 1. Check the plumbing to ensure the fireplace has been the fireplace. hooked up the gas supply line. 2. The propane tank is empty. A. There is a weak pilot flame 1. The pilot flame must engulf the thermocouple. Clean and/or adjust the pilot for maximum flame impingement on the thermocouple. A. A blockage is preventing 1. Inspect the burner orifice for obstruction. Call a gas flow. qualified service technician. B. Defective valve. 1. Replace the gas valve. Call a qualified service technician. Quadra-Fire • Fogata Grande October 2006...
  • Page 16: Maintaining And Servicing The Appliance 6

    Remove any foreign objects Inspect for paint condition, warpage, corrosion. Sand and repaint as necessary. Verify unobstructed air circulation. Inspect for broken, damaged or missing logs. Replace as necessary. Verify correct log placement and no flame impingement causing sooting. Correct as necessary. Verify logs are clean and carbon (soot) free. Logs may be cleaned with a dry bristle brush or dry cloth. Handle logs with care as they are fragile and easily damaged. Verify all gas connections are tight and leak-free. Clean off burner top corrosion or deterioration. Replace burner if necessary. Check for smooth lighting and ignition carryover to all ports. Verify there is no ignition delay. Inspect for lifting or other flame problems. Inspect orifice for soot, dirt or corrosion. Verify manifold and inlet pressures. Adjust regulator as required. Quadra-Fire • Fogata Grande WARNING Annual inspection by qualified technician recommended. Check: • Obstructions of combustion and ventilation air. • Condition of logs. • Condition of burner assembly. • Burner ignition and operation. • Burner air shutter adjustment. • Gas connections and fittings. Risk of: • Fire • Delayed ignition or explosion...
  • Page 17: Reference Materials

    Reference Materials A. Service Parts List Description of Part Valve Assembly Complete Thermopile Burner Assembly Complete Pilot Assembly (without Thermopile) Service Parts Quadra-Fire • Fogata Grande FOGATA GRANDE Part Number SRV-FG-VA SRV-FG-THPL SRV-FG-BA SRV-FG-PA October 2006 Qty.
  • Page 18: Logs

    Description of Part Log  Log 2 Log 3 Log 4 Log 5 Log 6 Log 7 Log 8 Log 9 Service Parts Log 2 Log 5 Log 8 Quadra-Fire • Fogata Grande FOGATA GRANDE Log 3 Log 6 Log 9 Part Number Qty. SRV-FG-00 SRV-FG-002 SRV-FG-003 SRV-FG-004 SRV-FG-005 SRV-FG-006 SRV-FG-007 SRV-FG-008...
  • Page 19 Log 13 Description of Part Log 0 Log  Log 2 Log 13 Log 4 Log 15 Log 6 Log 7 Service Parts Log 11 Log 14 Log 16 Quadra-Fire • Fogata Grande FOGATA GRANDE Log 12 Log 15 Log 17 Part Number SRV-FG-00 SRV-FG-0 SRV-FG-02 SRV-FG-013 SRV-FG-04 SRV-FG-015 SRV-FG-06 SRV-FG-07 October 2006 Qty.
  • Page 20: October

    To obtain service under this warranty, you must: 1. Send written notice of the claimed condition to: The Technical Services Department, Hearth & Home Technologies Inc., Mt. Pleasant, 1915 W. Saunders St., Mt. Pleasant, IA 52641 (phone: 1-800-927-6841). 2. Affirm that you are the original owner of the Product. 3. Provide Hearth & Home Technologies reasonable opportunity to investigate the claim, including reasonable opportunity to inspect the Product prior to any repair or replacement work and before the Product or any component of the Product has been removed. 4. Obtain Hearth & Home Technologies’ consent to any warranty work before the work is done. © 2004 Hearth & Home Technologies Inc. Hearth & Home Technologies Inc. Quadra-Fire • Fogata Grande October 2006 803-905 8/04...

This manual is also suitable for:

Fg21sp-ng

Table of Contents