1. DVR Features ...1 2. Layout Front Panel Rear Panel Remote Control 3. Installation Installing the Hard Drive Connecting Camera and Monitor Connecting Power Supply…………………………..…..3 4. System Boot Detecting Installed Hard Drive Recovering Lost Data Restore Recording Feature Main Screen 5.
Page 3
Start Recording Stop Recording Recording Time on Hard Drive 7. Playback ...14 8. USB Programming ...15 PC Viewer Program...15 Program Buttons...15 PC Backup 9. Specifications ...17 10. Appendix 10.1 System Connection Diagram...18 10.2 DVR Accessories (included) ...18 Q-SEE Product Warranty ...19...
Chapter 1: DVR Features 4 Channel BNC Camera Input 1 Channel BNC Video Output Video Source Option: NTSC / PAL Motion Detection with Sensitivity and Area Settings Time Schedule Recording / Motion Triggered Recording One ATA-100 Hard Disk Interface USB 2.0 Back up to computer Remote Control 2.1 Front Panel...
2.2 Rear Panel 1 BNC video output 4 BNC video inputs USB Port is located on the right side of the case. 2.3 Remote Control Quad Menu Power Supply Input Select or enlarge Channel #1 Select or enlarge Channel #2 Select or enlarge Channel #3 Select or enlarge Channel #4 Quad View...
2.2 Rear Panel). Attach the cable from each of the cameras to one of the BNC video input ports. Attach a RCA video cable (not included) to the video out put port on the DVR using a RCA to BNC adapter (included) and to a RCA video in port on the TV. 3.3 Connecting Power Supply Please only use the power adapter supplied with the DVR.
On the screen it will show the hard drive information. A power error can cause data to be lost, and the DVR system can automatically recover lost data after power is reconnected. If a power error occurs during the recording process, the system will automatically resume recording after power is reconnected.
SCHEDULE SET MISCELLANEOUS MENU HARD DISK SET MOTION SET VIDEO MODE FACTORY RESET QSD004 User’s Manual While the DVR is running, the monitor will display the information from the cameras as follows: Upper left: Percentage of space used on hard drive.
Page 9
Configure which channels you want to record. Note: If no channels are selected, an error message will appear briefly on the screen when record is selected. QSD004 User’s Manual Menu]: enter system menu 1 2 3 4 Note: If you are recording to enter...
Page 10
Record Schedule Settings (5.7 Schedule Set). QUAD Mode: The DVR will compress and record all 4 video channels into one file, therefore, you cannot enlarge a single channel to full screen in play back mode or live monitoring mode.
Page 11
After pressing [ REC] button, if the schedule is set to be “T” at that time, DVR will start to record immediately; if the schedule is set to be “M”, DVR will not start record until motion is captured and detected by system.
5.8 Miscellaneous Menu-Auto Record When the function is set to “ON”, DVR will be awaked to record automatically by record schedule if DVR is without any manual operation in five (5) minutes. When you choose “OFF”, DVR will not record until you press the [ REC] button.
If you format the hard drive, it will erase all the data on the hard drive. You need to input your password when you want to format the HDD. Note: When you install a new hard drive in the DVR, you use this function to format the hard drive.
MOTION ALARM TIME: This number indicates how many seconds the buzzer inside the DVR will sound after the DVR has been triggered by motion. CONT: Continuous alarm until press any key to stop.
[ SEL] button, please be patient! If you forget your password, please keep the system on main screen, and then press [Pause] button ten (10) times, the DVR will reset the system. Then the default password will be: [CH1] button six (6) times.
You can estimate recording hours by the formula: 120 (G Byte) × 1024 (M Byte) × 1024 (K Byte) 15 (Kbyte/frame) × 7 (frame/sec.) × 60 (sec.) x 60 (min.) Estimated time would be 332 Hours. QSD004 User’s Manual Frame Rate 20 K Bytes 15 K Bytes...
Press [ Play] button to play the latest recording. During playback, press the [ from the hard drive. Newest video will be listed at the top. Press [ Up] and [ Down] to move the cursor and select an event, press [ Play] button to start playback.
Chapter 8: USB Programming By connecting the DVR to a PC you can use PC Viewer software to play back and backup DVR recorded video through the USB 2.0 port. 8.1 PC Viewer Program 1. Put the USB Driver Program CD into your CD-ROM Drive 2.
PC Mode: play video clip (.mys file) save in PC 8.3 PC Backup Press button to open the DVR recorded event list, and then select an event, press to start backup. The video file you want to save in PC can be “.avi”...
Note: refer to 2.2 Rear Panel on page 2 for connections. DVR Accessories (included) 10.2 Power Cord The shape of the plug might different different countries or regions. CD-ROM QSD004 User’s Manual Power Adaptor Remote Controller - 18 - User’s Manual USB Cable...
Register link. Customer Information Card User’s Name Company Name Postal Address Postal code Phone Number E-mail Model Number of Product Serial Number of Product Purchase Date Distributor QSD004 User’s Manual - 19 - www.q-see.com website and Mr./Mrs.