Logging Mobile Units Onto A Telephone System - Siemens Gigaset 2000C Operating Instructions Manual

Putting the mobile unit into service
Mobile unit operating hours (battery life):
These times are only achieved after several charging and
discharging cycles!
Standby mode When phone in use
Type
(hours)
NiCd, 600 mAh up to 70
NiMH, 1100 mAh up to 110
NiMH, 1300 mAh up to 130
Permitted batteries:
Nickel-Cadmium Nickel-Metal-Hydride
Saft RC6 Sanyo HR-3 U (1300 mAh)
Panasonic P-60 AA/1P GP GP120 AA HC
Philips R6 NC-P Emmerich CE R 6
UCAR RC6 Energizer EMH-1100 AAC
Energizer Eveready XC 6 Varta VH 1101 AA
DAIMON ACCU 1000
Sanyo N-3U
Varta Accu Plus Ni-Cd 1,2V
No. 5006
Instructions for the use of NiMH batteries:
After you have inserted the NiMH batteries, we recom-
mend that the mobile unit be fully charged and then dis-
charged until the battery warning beep is heard, i.e.
without replacing the batteries in the charging shell. This
ensures that the charge status display
mobile unit is adapted to the increased operating life of
the NiMH batteries.
You can subsequently place your mobile unit in the
charging shell each time it is used. Charging is electron-
ically controlled which ensures that the batteries are
charged optimally.
16
Putting the mobile unit into service
.

Logging mobile units onto a telephone system

For information on setting the language, see page 56.
Your system administrator supplies you with mobile units
that have already been logged on when you are installing
(hours)
the system for the first time. You must log on any new
mobile units as described below if you extend the system.
up to 7
Please call Siemens Service if you purchased the mobile
up to 11
unit directly from Siemens. Please call your retailer if
you did not purchase your mobile unit directly from Sie-
up to 13
mens. Please ask Siemens Service or your retailer to pro-
vide you with the call number and the system code (eight-
digit) of every mobile unit and to open the "logon window"
(e.g. 10 minutes).

Logging a mobile unit onto Hicom 150 E:






  

  
of the

  

* See note "Base/system" on page 18
Switch the mobile unit on with the On/
  
appears in the
Off key -
display with the first logon procedure.

 
* , for example, flashes with the
second logon procedure.
Press the menu key – the main menu
is displayed .
Scroll with the left display key until
  
is selected (in the top dis-
play line) and confirm the selection
with the right display key.
Scroll with the left display key until
  
is selected and confirm.

 
Confirm *, for example, to log
on as system 1.
If necessary, select another base/
system with the display key.
   
is displayed .
17
Putting the mobile unit into service

e.g. Enter the mobile unit system code
...
(eight-digit) and confirm the entry with
the display key –
  
played instead of digits.

if necessary, press the display keys
and
entry.

 
*, for example, is displayed.
 
The mobile unit is successfully logged
on (registered) if the ring symbol
flashes (this can take up to 30 sec-
onds).
The mobile unit ready to receive or
 
transmit calls if this display is retained.
Note:
Base/system: cordless EM mobile units are not logged
onto bases (base stations), but rather onto the Hicom
150 E telephone system. In this case,
means DECT** system.
No ring symbol is displayed if the logon procedure was
unsuccessful.
* See note "Base/system"
** DECT = D igital E nhanced C ordless T elecommunications
18
symbols are dis-
to correct an


always