Configuring The Slave Side Of Spvcs; Table 2-7 Parameters For The Addcon Command - Cisco MGX 8850 PXM1E Software Configuration Manual And Command Reference

General AUSM Provisioning Procedures
Double-ended SPVCs require separate configuration of the master and slave endpoints. The slave
endpoint must be configured first because this step generates a slave address that must be entered during
master endpoint configuration.
The following sections describe how to configure slave and master SPVC connections.

Configuring the Slave Side of SPVCs

If you wish to configure a double-ended SPVC connection, you must first configure the slave endpoint
for the connection. If you are configuring a single-ended SPVC, you need not configure a slave endpoint.
To configure the slave side of a double-ended SPVC, perform the following steps:
Establish a configuration session using a user name with GROUP1 privileges or higher.
Step 1
Step 2 Define the slave side of the SPVC by entering the following addcon command:
PXM1E_SJ.VHSHS2B.a > addcon <port_number> <vpi> <vci> [-ct <ConnectionType>]
[-contp <ControllerType>] [-st
[-abrtype <ABRType>] [-abrpcr
[-ipcu <IngrPercentUtil>] [-epcu <EgrPercentUtil>] [-upce <UpcEnable>]
[-scrp <SCRPolicing>] [-ccdv <CDVT[0+1]>] [-cte <CLPTagEnable>] [-dis <DiscardOption>]
[-pcr01 <IngrUpcPCR[0+1]>] [-scr <IngrUpcSCR>] [-cbs <MaxBurstSize>] [-maxcost <MaxCost>]
[-rtngpri <RoutingPriority>] [-type <restrictedType>] [-rpcr <RemotePCR>]
[-rscr <RemoteSCR>] [-rmcr <RemoteMCR>] [-rcbs <RemoteMaxBurstSize>]
Note If the addcon command fails and displays the "Failed to update disk" message, it could be that the PNNI
controller has not been added on the PXM1E card. For information on adding the PNNI controller, refer
to the Cisco MGX 8850 (PXM1E) and MGX 883Cisco MGX 8850 (PXM1E) and MGX 8830 Software
Configuration Guide, Release 3.
Table 2-7
in this table refer to settings for the local port you are configuring and the remote port at the other end
of the connection. If you omit an option, a default value for that option is used for SPVC configuration.
Caution Once you create an SPVC connection, you cannot change the SPVC prefix until all SPVC connections
have been deleted. The procedure for changing the SPVC prefix is described in the Cisco MGX 8850
(PXM1E) and MGX 883Cisco MGX 8850 (PXM1E) and MGX 8830 Software Configuration Guide,
Release 3.
Table 2-7
Parameter
port_num
vpi
vci
Cisco AUSM Software Configuration Guide and Command Reference for MGX 8850 (PXM1E) and MGX 8830
2-16
<ABRPCR>] [-abrmcr <ABRMCR>] [-osub <OvrSubFlag>]
lists and describes the parameters for the addcon command. The local and remote terms used
Parameters for the addcon Command
Description
Enter the port number for the ATM port or IMA group to which you will add the
connection. To display a list of configured ports, enter the dspports command.
Enter a VPI number in the range from 0 to 255.
Enter a VCI number in the range from 35 to 65535. For virtual path connections,
enter *.
<ServiceClassTtype>] [-master
Release 3, Part Number 78-14254-01 Rev. A0, October 2002
Chapter 2 Provisioning Communications Links
<MasterShip>]