Mitsubishi Electric MDS-D-SPJ3 Specification Manual page 91

MITSUBISHI CNC
3 Function Specifications
(Spindle control signal)
Spindle control input (NC to Spindle)
No.
16384 Spindle control input 1-0
16385 Spindle control input 1-1
16391 Spindle control input 1-7
16392 Spindle control input 1-8
16393 Spindle control input 1-9
16394 Spindle control input 1-A
16432 Spindle control input 4-0
16433 Spindle control input 4-1
16434 Spindle control input 4-2
16436 Spindle control input 4-4
16437 Spindle control input 4-5
16438 Spindle control input 4-6
16459 Spindle control input 5-B
16460 Spindle control input 5-C
16461 Spindle control input 5-D
16462 Spindle control input 5-E
(Note 1) Control signal is bit output. Setting the No. of the table above to the data output(SP125, SP126),
and when the scale (SP127, SP128) is set to "0", the output is "0V" for bit 0, and "2.5V" for bit 1.
(Note 2) Refer to the section "Spindle control signal" in Instruction Manual for details on the spindle control
signal.
3 - 26
Details
READY ON command
Servo ON command
Alarm reset command
Torque limit 1 selection com-
mand
Torque limit 2 selection com-
mand
Torque limit 3 selection com-
mand
Spindle control mode selec-
tion command 1
Spindle control mode selec-
tion command 2
Spindle control mode selec-
tion command 3
Gear changeover command
Gear selection command 1
Gear selection command 2
Minimum excitation rate 2
changeover request
Speed gain set 2 changeover
request
Zero point re-detection re-
quest
Spindle holding force up
Spindle control output (Spindle to NC)
No.
16480 Spindle control output 1-0
16481 Spindle control output 1-1
16487 Spindle control output 1-7
16488 Spindle control output 1-8
16489 Spindle control output 1-9
16490 Spindle control output 1-A
16492 Spindle control output 1-C
16495 Spindle control output 1-F
16496 Spindle control output 2-0
16499 Spindle control output 2-3
16503 Spindle control output 2-7
16528 Spindle control output 4-0
16529 Spindle control output 4-1
16530 Spindle control output 4-2
16532 Spindle control output 4-4
16533 Spindle control output 4-5
16534 Spindle control output 4-6
16545 Spindle control output 5-1
16555 Spindle control output 5-B
16556 Spindle control output 5-C
16557 Spindle control output 5-D
16558 Spindle control output 5-E
16559 Spindle control output 5-F
Details
In ready ON
In servo ON
In alarm
In torque limit 1 selection
In torque limit 2 selection
In torque limit 3 selection
In in-position
In warning
Z phase passed
In zero speed
In external emergency stop
In spindle control mode se-
lection 1
In spindle control mode se-
lection 2
In spindle control mode se-
lection 3
In gear changeover com-
mand
In gear selection 1
In gear selection 2
Speed detection
In minimum excitation rate 2
selection
In speed gain set 2 selection
Zero point re-detection com-
plete
Spindle holding force up
completed
In 2nd in-position