General Power Tool Safety Warnings; Save All Warnings And Instructions For Future Reference; Additional Safety Rules For Tool - Makita LS1040FS Instruction Manual
Hide thumbs
Also See for LS1040FS:
- Instruction manual (109 pages) ,
- Instruction manual (89 pages) ,
- Instruction manual (93 pages)
Table of Contents
Advertisement
Available languages
Available languages
The declared vibration emission value may also be
•
used in a preliminary assessment of exposure.
WARNING:
The vibration emission during actual use of the
•
power tool can differ from the declared emission
value depending on the ways in which the tool is
used.
Be sure to identify safety measures to protect the
•
operator that are based on an estimation of
exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as
the times when the tool is switched off and when it
is running idle in addition to the trigger time).
ENH003-13
For European countries only
EC Declaration of Conformity
We
Makita
Corporation
as
the
responsible
manufacturer declare that the following Makita
machine(s):
Designation of Machine:
Compound Miter Saw
Model No./ Type: LS1040F, LS1040FS
are of series production and
Conforms to the following European Directives:
2006/42/EC
And are manufactured in accordance with the following
standards or standardised documents:
EN61029
The technical documentation is kept by our authorised
representative in Europe who is:
Makita International Europe Ltd.
Michigan Drive, Tongwell,
Milton Keynes, Bucks MK15 8JD, England
30. 1. 2009
000230
Tomoyasu Kato
Director
Makita Corporation
3-11-8, Sumiyoshi-cho,
Anjo, Aichi, 446-8502, JAPAN
GEA010-1
General Power Tool Safety
Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for
future reference.
ENB120-1
ADDITIONAL SAFETY RULES
FOR TOOL
1.
Wear eye protection.
2.
Keep hands out of path of saw blade. Avoid
contact with any coasting blade. It can still
cause severe injury.
3.
Do not operate saw without guards in place.
Check blade guard for proper closing before
each use. Do not operate saw if blade guard
does not move freely and close instantly.
Never clamp or tie the blade guard into the
open position.
4.
Do not perform any operation freehand. The
workpiece must be secured firmly against the turn
base and guide fence with the vise during all
operations. Never use your hand to secure the
workpiece.
5.
Never reach around saw blade.
6.
Turn off tool and wait for saw blade to stop
before moving workpiece or changing settings.
7.
Unplug
tool
before
changing
blade
or
servicing.
8.
Always secure all moving portions before
carrying the tool.
9.
Stopper pin which locks the cutter head down
is for carrying and storage purposes only and
not for any cutting operations.
10. Do not use the tool in the presence of
flammable liquids or gases. The electrical
operation of the tool could create an explosion and
fire when exposed to flammable liquids or gases.
11.
Check the blade carefully for cracks or
damage before operation.
Replace
cracked
or
damaged
blade
immediately.
12. Use only flanges specified for this tool.
13. Be careful not to damage the arbor, flanges
(especially the installing surface) or bolt.
Damage to these parts could result in blade
breakage.
14. Make sure that the turn base is properly
secured so it will not move during operation.
15. For your safety, remove the chips, small pieces,
etc. from the table top before operation.
16. Avoid cutting nails. Inspect for and remove all
nails from the workpiece before operation.
17. Make sure the shaft lock is released before the
switch is turned on.
18. Be sure that the blade does not contact the
turn base in the lowest position.
19. Hold the handle firmly. Be aware that the saw
moves up or down slightly during start-up and
stopping.
20. Make sure the blade is not contacting the
workpiece before the switch is turned on.
Page 7
Advertisement
Table of Contents
