Advertisement
DeviceControl
Name
Access Short ASCII
DeviceVendorName
R/O
DeviceModelName
R/O
DeviceVersion
R/O
DeviceFirmwareVersion
R/O
DeviceFpgaVersion
R/O
DeviceSerialNumber
R/O
DeviceUserID
R/W
DeviceTempoerature
R/O
DeviceReset
W/O
TechnologySpecificBootstrapRegister
Access Short ASCII
Name
SupportedBaudrates
R/O
CurrentBaudrate
R/W
ImageFormatControl
Name
Access Short ASCII
Width
R/W
OffsetX
R/W
BinningHorizontal
R/W
Values
DVN
"JAI Corporation"
MD
"SW-4000TL-PMCL"
Indicate device version
DV
(e.g. "0.1.0.0" )
VN
"*.*.*.*"
FPVN
"*.*.*.*"
ID
Serial Number
User can save and load free text.
UD
(64 or less characters)
TMP0
CSR00
1
Values
Indicate Support/Non-support status for
each baud rate
bit0: 9600bps
SBDRT
bit1: 19200bps
bit2: 38400bps
bit3: 57600bps
bit4: 115200bps
READ: Indicate current baud rate
WRITE: Set any bit of baud rate
bit0: 9600bps
CBDRT
bit1: 19200bps
bit2: 38400bps
bit3: 57600bps
bit4: 115200bps
Values
WTC
Min～(Max - OffsetX)
OFC
Min～(Max – Width)
1: Binning Off
HB
2: Binning On
MIN
MAX
DEFAULT Description
DVN?<CR><LF>
-
-
-
Display the manufacture name.
MD?<CR><LF>
-
-
-
Display the model name.
DV?<CR><LF>
-
-
-
Display the camera version.
VN?<CR><LF>
-
-
-
Display the version of firmware.
FPVN?<CR><LF>
-
-
-
Display the version of fpga.
ID?<CR><LF>
-
-
-
Display the device ID.
UD=[Param.]<CR><LF>
UD?<CR><LF>
Set the user ID for the camera
TMP0?<CR><LF>
Display the device temperature in degrees Celsius (C).
CRS00=1<CR><LF>
-
-
-
Reset the device.
MIN
MAX
DEFAULT Description
SBDRT?<CR><LF>
0x01
0xFF
0x1F
This camera supports 9600bps, 19200bps, 38400bps,
57600bps, and 115200bps.
CBDRT=[Param.]<CR><LF>
CBDRT?<CR><LF>
1
0x01
0x80
(9600bps
In case of WRITE execution (change baud rate), it needs to
)
control in the proper sequence between Host and Camera.
(Refer to the section 3.3)
MIN
MAX
DEFAULT Description
WTC=[Param.]<CR><LF>
WTC?<CR><LF>
Set the image width.
16
4096
4096
※
BinningHorizontal=1:16~4096, Step:16Pix/Step
BinningHorizontal=2: 8~2048, Step: 8Pix/Step
(The value will be set configuration steps)
OFC=[Param.]<CR><LF>
OFC?<CR><LF>
Set the horizontal offset.
0
4080
0
※
BinningHorizontal=1:0~4080, Step:16Pix/Step
BinningHorizontal=2:0~2040, Step: 8Pix/Step
(The value will be set configuration steps)
HB=[Param.]<CR><LF>
HB?<CR><LF>
1
2
1
Set the number of pixels in the horizontal direction for
whitch to perform binning.
Advertisement
