Cisco ONS 15454 Series Reference Manual page 3

ONS_15454_Reference_Manual_R8.5.x_--_Shelf_and_Backplane_Hardware
♦ 5.8 UBIC-V EIA
5.9 UBIC-H EIA
♦
♦ 5.10 EIA Replacement
• 6 Coaxial Cable
• 7 DS-1 Cable
♦ 7.1 Twisted Pair Wire-Wrap Cables
♦ 7.2 Electrical Interface Adapters
• 8 UBIC-V Cables
♦ 8.1 Figure 1-23: Cable Connector Pins
8.2 Table 1-16: UBIC-V DS-1 and DS-3/EC-1 Pin Assignments
♦
8.3 Table 1-17: UBIC-V EIA DS-1 Wiring
♦
9 UBIC-H Cables
•
9.1 Figure 1-24: Cable Connector Pins
♦
♦ 9.2 Table 1-18: UBIC-H DS-1 and DS-3/EC-1 Pin Assignments
♦ 9.3 Table 1-19: UBIC-H EIA DS-1 Wiring
• 10 Ethernet Cables
♦ 10.1 Table 1-20: E100-TX Connector Pinout
♦ 10.2 Figure 1-25: 100BaseT Connector Pins
♦ 10.3 Figure 1-26: Straight-Through Cable
♦ 10.4 Figure 1-27: Crossover Cable
• 11 Cable Routing and Management
♦ 11.1 Figure 1-28: Managing Cables on the Front Panel
♦ 11.2 Fiber Management
♦ 11.3 Fiber Management Using the Tie-Down Bar
♦ 11.4 Coaxial Cable Management
♦ 11.5 DS-1 Twisted-Pair Cable Management
11.6 AMP Champ Cable Management
♦
12 Alarm Expansion Panel
•
12.1 Figure 1-31: AEP Printed Circuit Board Assembly
♦
12.2 Figure 1-32: AEP Block Diagram
♦
♦ 12.3 Wire-Wrap and Pin Connections
Contents
◊ 5.7.3 Table 1-9: AMP Champ Connector Pin Assignments (Shielded DS-1 Cable)
◊ 5.8.1 Figure 1-20: UBIC-V Slot Designations
5.8.2 Table 1-10: UBIC-V Protection Types and Slots
◊
5.9.1 Figure 1-21: UBIC-H EIA Connector Labeling
◊
5.9.2 Table 1-11: J-Labeling Port Assignments for a Shelf Assembly Configured
◊
with Low-Density Electrical Cards (A Side)
◊ 5.9.3 Table 1-12: J-Labeling Port Assignments for a Shelf Assembly Configured
with Low-Density Electrical Cards (B Side)
◊ 5.9.4 Table 1-13: J-Labeling Port Assignments for a Shelf Configured with
High-Density Electrical Cards (A Side)
◊ 5.9.5 Table 1-14: J-Labeling Port Assignments for a Shelf Configured with
High-Density Electrical Cards (B Side)
◊ 5.9.6 Table 1-15: UBIC-H Protection Types and Slots
◊ 7.2.1 Figure 1-22: DS-1 Electrical Interface Adapter (Balun)
◊ 11.2.1 Figure 1-29: Fiber Capacity
◊ 11.2.2 Table 1-21: Fiber Channel Capacity (One Side of the Shelf)
◊ 11.3.1 Figure 1-30: Tie-Down Bar
◊ 12.3.1 Figure 1-33: AEP Wire-Wrap Connections to Backplane Pins
◊ 12.3.2 Table 1-22: Pin Assignments for the AEP
◊ 12.3.3 Figure 1-34: Alarm Input Circuit Diagram
◊ 12.3.4 Table 1-23: Alarm Input Pin Association
◊ 12.3.5 Figure 1-35: Alarm Output Circuit Diagram
3