Advertisement
Quick Links
SYSTXCCSAN0t
lnfinit
S stem Access
NoduMe
\isit
"__ _.carrier.com
Installation and Start-Up
instructions
HEATUNG & COOLING
This is the safety°alert symbol z_
When you see this symbol on
the equipment
and in the instruction
manual,
be alert to the
potential for personal i11.iu W [ nderstand the signal words DAN-
GER, _'_ARNING,
and CA[ TION
These words are used _ith
the sa_kty°alert symbol
DANGER
identifies the most serious
hazards, _hich
will result in sexere personal in3uU or death.
_ARNING
signifies a hazard, which could result in personal
iaju W or death (A[
TION is used to identK)- unsafe practices,
which ma? result in minor personal irwin W or product and property
damage. NOTE is used to highlight suggestions which will result
in enhanced installation, reliability, or operation.
INSTALLATION
CONSIDERATIONS
Infinity System Access
Module
SYSTXCCSAN01
A97040
NOTE:
Read the entire instruction manual be%re starting the
installation
This symbol --> indicates a change since the last issue.
TABLE OF CONTENTS
SAFETY ( ONSIDERATIONS
1
INSTALLATION
CONSIDERATIONS
.......................................
1
INTRODUCTION
....................................
1
INSTALLATION
..........................................
! ° 3
Check Equipment and Job Site .......................
1
Component Location and Wiring (onsiderations
........
2
Connect Power Source ...........................
2
Radio Test ......................................
2
Install ( omponents ..............................
2
Connect Infinity Systems .........................
2
Connect Water Sensor ...........................
2
System Start°E p ................................
3
PIN Number ...................................
3
RS=232 ( onnector ....................................
3
Updating System Profile ................................
3
Troubleshooting ......................................
3
SAFETY CONSIDERATmONS
Improper installation, adjustment, alteration, service, maintenance,
or use can cause fiie, electrical shock, or other conditions that may
cause personal injury or property damage. Consult a qualified
installer, service agency, or your distributor or branch for infor=
marion or assistance. The qualified installer or agency must use
factory authorized kits or accessories when modifying this product.
RefEr to the individual
instl_actions packaged
with the kits or
accessories
when installing. Follow all safety codes and wear
safety glasses. Have fire extinguisher
available. Read these in=
structions thoroughly and [bllow all warnings or cautions attached
to the unit. Consult local and state building codes and Sheet Metal
and Air Conditioning National Association (SMACNA) %r special
installation requirements.
Before
the actual
installation
of a System
Access
Module
can
begin,
determine
the
mounting
location.
A radio
test must
be
performed
with
the
System
Access
Module
in
the
intended
mounting
location.
See below
on how to perform
a radio test. The
System
Access
Module
is powered
with
a 24 VA(
transformer
(included).
A 120VAC
supply must be near the mounting
location
of the System
Access
Module.
Provisions
must be made to secure
the
transformer
to the
outlet.
The D=wire
(24 VAC)
l_-om the
Infinity
system
MIST
NOT
be used to power
the System
Access
Module.
Use this instruction
to guide the actual installation
process
after
the
Infinity
system(s)
have
been
installed.
One
System
Access
Module
is capable
of handling
two Infinity
systems.
mNTRODUCTION
An Infinity
System
Access
Module
allows
remote
com_ectivity
%r
up to two Infinity
systems
within
the same building
_he Infinity
system
owner
as well as authorized
dealer
can monitor
and control
the system
via the interact
as well as by telephone.
The System
Access
Module
communicates
d_rough
a two-way
radio
via the
Skytel
paging
network.
Please
visit:
http:iiwww.skvtel
comicovera_eitelemetlw
coverage
htm to check
coverage
for the installation
site. The coverage
must
be listed
as
"Full Service"
for the System
Access
Modtde
to _imction properly.
Please note that Skytel is continuously
expanding
their service
area
so coverage
may not be indicated
by the web site.
The System
Access
Module
can also monitor
a &y=contact
sensor
to provide
a
warning
for the presence
of water
in the building,
or some other
use. If the sensor is active,
the Infini w system
will not be disabled
or shut down.
mNSTALLATION
Step l--Check
Equipment
and Job Site
INSPE(T
EQ[ IPMENT
File claim with shipping company,
prior to installation, if shipment is damaged or incomplete
Manufacturer
reserves
the
right
to discontinue,
or
change
at any
time,
specifications
or designs
without
notice
and
without
incurring
obligations.
_2
PC 101
Printed
in USA
Catalog
No.
SAM01-1SI
Pg 1
05-05
Replaces:
NEW
a
Advertisement
