GE C30 Instruction Manual page 170

5.2 PRODUCT SETUP
The optional user-programmable pushbuttons (specified in the order code) provide an easy and error-free method of enter-
ing digital state (on, off) information. The number of available pushbuttons is dependent on the faceplate module ordered
with the relay.
• Type P faceplate: standard horizontal faceplate with 12 user-programmable pushbuttons.
• Type Q faceplate: enhanced horizontal faceplate with 16 user-programmable pushbuttons.
The digital state can be entered locally (by directly pressing the front panel pushbutton) or remotely (via FlexLogic™ oper-
ands) into FlexLogic™ equations, protection elements, and control elements. Typical applications include breaker control,
autorecloser blocking, and setting groups changes. The user-programmable pushbuttons are under the control level of
password protection.
The user-configurable pushbuttons for the enhanced faceplate are shown below.
USER USER USER
LABEL 1 LABEL 2 LABEL 3
Figure 5–6: USER-PROGRAMMABLE PUSHBUTTONS (ENHANCED FACEPLATE)
The user-configurable pushbuttons for the standard faceplate are shown below.
5
USER LABEL
USER LABEL
Figure 5–7: USER-PROGRAMMABLE PUSHBUTTONS (STANDARD FACEPLATE)
Both the standard and enhanced faceplate pushbuttons can be custom labeled with a factory-provided template, available
online at http://www.GEmultilin.com. The EnerVista UR Setup software can also be used to create labels for the enhanced
faceplate.
Each pushbutton asserts its own "On" and "Off" FlexLogic™ operands (for example,
). These operands are available for each pushbutton and are used to program specific actions. If any pushbutton is
1 OFF
active, the
ANY PB ON
Each pushbutton has an associated LED indicator. By default, this indicator displays the present status of the correspond-
ing pushbutton (on or off). However, each LED indicator can be assigned to any FlexLogic™ operand through the
setting.
1 LED CTL
The pushbuttons can be automatically controlled by activating the operands assigned to the
self-reset mode) and
PUSHBTN 1 RESET
operand is asserted. The activation and deactivation of user-programmable pushbuttons is dependent
PUSHBUTTON 1 OFF
on whether latched or self-reset mode is programmed.
• Latched mode: In latched mode, a pushbutton can be set (activated) by asserting the operand assigned to the
setting or by directly pressing the associated front panel pushbutton. The pushbutton maintains the set state
BTN 1 SET
until deactivated by the reset command or after a user-specified time delay. The state of each pushbutton is stored in
non-volatile memory and maintained through a loss of control power.
The pushbutton is reset (deactivated) in latched mode by asserting the operand assigned to the
ting or by directly pressing the associated active front panel pushbutton.
5-46
USER USER USER USER
LABEL 4 LABEL 5 LABEL 6 LABEL 7
1 3
USER LABEL
2 4
USER LABEL
operand will be asserted.
(for latched mode only) settings. The pushbutton reset status is declared when the
C30 Controller System
USER USER USER USER
LABEL 8 LABEL 9 LABEL 10 LABEL 11
5 7
USER LABEL USER LABEL
6 8
USER LABEL USER LABEL
5 SETTINGS
USER USER USER USER
LABEL 12 LABEL 13 LABEL 14 LABEL 15
9 11
USER LABEL USER LABEL
10 12
USER LABEL USER LABEL
842779A1.CDR
and
PUSHBUTTON 1 ON PUSHBUTTON
(for latched and
PUSHBTN 1 SET
PUSHBTN 1 RESET
GE Multilin
USER
LABEL 16
842814A1.CDR
PUSHBTN
PUSH-
set-