Table of Contents
Advertisement
Quick Links
Model APS-20B
Installation Manual
Vehicle Alarm System
With Auxiliary Output
Installation Instructions
This Unit Is Intended For Installation In Vehicles With
12 Volt Negative Ground Electrical Systems Only
Kit Contents:
APS-20B Control Module
(2) - Three Button Transmitters
3 Channel Code Learning Receiver
(1) - Multi Pin Input/Output Harness
(1) - Two Pin Door Lock Harness
(1) - Two Pin LED Indicator
(1) - Two Pin Valet / Programming Switch
Multi-tone Siren
(1) - Installation Manual
(1) - Operator's Manual
(1) - Limited Warranty
(2) - Window Decals
128-6187B
Revised: REV. B
1-30-03 (Corrected Blue Wire from Channel 3 to Channel 2)
1 of 8
Revised: REV. A
1-21-03 (Corrected page 8, Wiring Diagram)
Released 11-6-01.
Changed 1-23-02.(note: No Rev was Required)
Corrected 2-15-02.(note: No Rev was Required)
Corrected 3-4-03.(note: No Rev was Required)
Advertisement
Table of Contents
Related Manuals for Prestige APS-20B
Summary of Contents for Prestige APS-20B
- Page 1 Installation Instructions This Unit Is Intended For Installation In Vehicles With 12 Volt Negative Ground Electrical Systems Only Kit Contents: APS-20B Control Module (2) - Three Button Transmitters 3 Channel Code Learning Receiver (1) - Multi Pin Input/Output Harness (1) - Two Pin Door Lock Harness...
- Page 2 The APS-20B Vehicle Alarm System is designed to provide a basic deterrent to vehicle theft and a convenient electronic means to gain access to the vehicle by providing RF remote control over the vehicle's power door lock system. The unit also includes outputs to control the vehicle's parking lights and an additional auxiliary output designed to allow for control over an optional device such as a power trunk release or engine starting device.
-
Page 3: Wiring Connections
open), it will supply a ground to the input wire thus activating the alarm. Mount the switch in the hood or trunk locations away from water drain paths. If necessary, the included bracket may be used to move the switch away from rain gutters or allow mounting to the firewall behind the hood seal. - Page 4 DARK GREEN Wire: Negative (-) Hood/Trunk Trigger Input Wire This input is designed to connect to a grounding hood, trunk, or rear hatch pin-switch, to allow the system to trigger should those entry points be violated. To provide protection for the hood, the Dark Green negative hood/trunk trigger wire should connect to the existing factory hood pin-switch (if one exists) or to a suitable aftermarket installed hood pin-switch.
- Page 5 polarity" output scheme these two wires produce the opposite polarity at the opposite time. To better understand this, refer to the table below: Wire Color Green Green The output of these wires has a maximum switching capability of 300mA. Many vehicles today have factory door lock relays which can be connected directly to these outputs, however always confirm that the factory relays in your particular vehicle do not exceed the rated 300mA output of the units door lock/unlock circuit.
-
Page 6: Valet/Program/Manual Override Switch2
APS20B control module. Do not force the connector, it will only plug in one way. PROGRAMMING FEATURES: There are five (5) Programmable Features on the APS-20B system. Study the list below, keeping in mind the features and their defaults, (how it comes programmed from the factory), and decide how best to program the system for your particular installation. -
Page 7: Completing The Installation
mode and toggle the Valet/Program/Manual Override Switch 3 times in order to adjust the Fourth programmable feature. The system would respond with 1 Chirp and the LED would begin to flash 4 Flashes, pause and repeat. This has told you that the system is ready for you to adjust the Fourth programmable feature, and that it is currently programmed for Chirps ON. - Page 8 © 2003 Audiovox Electronics Corporation 128-6187B 128-6187B 8 of 8...