Using The M9.2S Preprogrammed Courses - Precor M 9.2s Owner's Manual

Precision electronic treadmill
Hide thumbs Also See for M 9.2s:
Table of Contents

Advertisement

CAUTION: If this is the first time you have
operated this treadmill, DO NOT STAND on
the running belt until you become familiar
the M9.2s operation. Be sure to read and
follow the general guidelines found in
"Working Out on Your Precor Treadmill."
CAUTION: Before beginning any fitness
program, you should have a complete
physical examination by your physician. If you
are unsure about your level of fitness, consult
your physician. Always start your workout at
the low or "WALK 1" level and work to
increase your level of fitness before perform-
ing moderate or advanced workout routines.
page 18
Once you reach your desired rest speed, the treadmill remembers that speed and returns to it
at the beginning of each rest interval, until you change the speed or end your workout.
2.
The next scrolling prompt requests that you specify your work speed ( and work incline —
M9.2s only ). With one hand on the handrail, use the other hand to press the SPEED
until the desired work speed (up to 9 mph) is shown. When you are comfortable with the rest
and work speeds, you can let go of the handrail.
Note: On the M9.1, use the incline crank handle to change the degree of incline. Hold onto the
handrail with one hand while you rotate the crank in a clockwise direction to raise the incline
with the other hand. To lower the incline, rotate the handle counterclockwise .
Each rest and work interval lasts 60 seconds. The display automatically counts down to the next
interval. When the count reaches 30 seconds, the display changes and gives information about
distance travelled, time elapsed, speed, calories burned, and percent of incline.
When the treadmill changes intervals, it informs you by scrolling a message across the display.
Using the interval course mode, you can cool down before ending your workout by pressing STOP
twice in quick succession. The treadmill enters manual mode, letting you specify the speed of your
cool-down period.

Using the M9.2s Preprogrammed Courses

To use a preprogrammed course, follow the instructions below. Remember, when you use the
electronic console, hold onto the handrail to maintain your balance. You should also use the
handrail whenever you speed up, slow down, or stop the treadmill.
1.
On the electronic console, move the magnetic safety key to the ACTIVATE position as shown
in Diagram 11, page 10. Walk to the front of the treadmill and turn ON the treadmill using the
ON/OFF switch. The treadmill switch will not turn ON unless the safety key is seated securely
in the ACTIVATE position.
2.
Straddle the running belt with your feet firmly planted on the right and left side platforms.
Stand close enough to the electronic console so that you can extend your arms and activate
the keys.
3.
Using the clip provided, securely attach the magnetic safety key to your clothing at your
waistline, where it will not interfere with your workout.
4.
When you see "ENTER WEIGHT" scroll across the display, specify your weight using any
key. When the correct weight is displayed, press ENTER. This information allows the M9.2s to
calculate how many calories you use during your workout.
The number on the display moves in 5-pound increments up or down, depending on the
arrow key pressed. Use
Once your weight is specified, you may not need to enter it again. The treadmill automatically
remembers the last weight entered (unless the treadmill is turned OFF). At your next workout,
you restore your weight from the treadmill's memory by simply pressing ENTER at the
"ENTER WEIGHT" prompt. However, if someone else has used the treadmill and made
changes prior to your workout, you will need to re-enter your weight.
Note: The prompt "PRESS ENTER TO BEGIN" appears after a few seconds if you have not
chosen a course and pressed ENTER. This prompt continues to scroll across the display every
few seconds until you press ENTER.
to increase and
to decrease the weight displayed.
keys

Hide quick links:

Advertisement

Table of Contents
loading

This manual is also suitable for:

M 9.1

Table of Contents