Important Safety Instructions Read the following precautions thoroughly before you begin assembly, and save them afterward for future reference. Safety Precautions Always follow basic safety precautions when using this equipment to reduce the chance of injury, fire, or damage. Other sections in this manual provide more details of safety features.
Page 6
Assembling and Maintaining the UBK 815 Upright Exercise Bike Use the power adapter provided with the equipment. Plug the power adapter into an appropriate, grounded power outlet as marked on the equipment. Keep the power cord or optional power adapter and plug away from heated surfaces.
The batteries within self-powered equipment contain materials that are considered hazardous to the environment. Federal law requires proper disposal of these batteries. If you plan to dispose of your equipment, contact Precor Commercial Products Customer Support for information regarding battery removal. Refer to Obtaining Service.
The regulatory information in this section applies to the exercise equipment and its control console. Safety Approvals for Cardiovascular Equipment Precor equipment has been tested and found to comply with the following applicable safety standards. Cardiovascular Type Equipment: CAN/CSA, IEC, EN 60335-1 (Household and similar...
Page 9
Important Safety Instructions Radio Frequency Interference (RFI) This Precor exercise equipment conforms to the following national standards defining acceptable limits for radio frequency interference (RFI). Federal Communications Commission, Part 15 This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
However, up to 15 consoles or PVS screens can be "daisy-chained" on a single power circuit. A 20 amp dedicated branch circuit is recommended for every such chain of consoles or screens. Assembling and Maintaining the UBK 815 Upright Exercise Bike...
Page 11
Important Safety Instructions The grounding plug on a treadmill or power supply looks like the plug shown in one of the following two figures. The power outlet must have the same configuration as the plug. Important: Do not use any power cord adapter with this product. Figure 1: 120-volt, 20-amp power plug Figure 2: 240-volt, 20-amp power plug...
If any items are missing, contact your dealer. For more information regarding customer support numbers or a list of Precor authorized service centers, visit the Precor web site at http://www.precor.com. Assembling and Maintaining the UBK 815 Upright Exercise Bike...
Regulatory Notices for Cardiovascular Exercise Equipment ... 6 120 V and 240 V Equipment Designated for U.S. Markets ... 8 Obtaining Service ... 10 Assembling the Exercise Bike ... 13 Unpacking the Equipment ... 14 Hardware Kit (not to scale) ... 15 ...
Page 14
Symptoms of a Low Battery ... 32 Using the Optional Power Adapter ... 33 The Optional Power Adapter Kit ... 33 Replacing the Battery ... 34 Commercial Equipment Limited Warranty ... 35 Assembling and Maintaining the UBK 815 Upright Exercise Bike...
Assemble the equipment according to the guidelines in this manual to ensure you do not void the Precor Limited Warranty. Important: Any damage caused during installation is not covered by the Precor Limited Warranty.
Assembling and Maintaining the UBK 815 Upright Exercise Bike Do not attempt to move the equipment off of the pallet by yourself. Have at least one other person help you, and use safe lifting techniques.
Assembling the Exercise Bike Hardware Kit (not to scale) Before you begin the assembly, verify that the following hardware items are packed with the equipment. Fasteners Required Tools -inch hex wrench -inch hex wrench -inch hex wrench #2 Phillips screwdriver...
Pull the upright rear cover back to remove it, then set it aside. Figure 3: Rear cover removal 3. Remove the two #10 x 1-inch self-tapping screws holding the top cover in place, then lift it off. Figure 4: Top cover removal Assembling and Maintaining the UBK 815 Upright Exercise Bike...
Page 19
Assembling the Exercise Bike 4. Remove the four #10 x 1-inch self-tapping screws holding the left side cover in place, then pull the cover away from the body assembly. Guide the cover around the pedal crank, then remove it and set it aside.
Page 20
Figure 7: Bolting the upright support into place Note: If you are not installing Cardio Theater equipment on the console, you do not need to complete the following two steps. Assembling and Maintaining the UBK 815 Upright Exercise Bike -inch hex wrench.
Assembling the Exercise Bike 9. Reposition the left side cover on the body assembly, then reattach and tighten the #10 x 1-inch self-tapping screws holding it in place. 10. Repeat the previous step to reinstall the top and rear covers.
4. Place the handlebar assembly onto the brackets and attach four the screws completely using a Assembling and Maintaining the UBK 815 Upright Exercise Bike -inch x -inch sockethead screws. Tighten -inch hex wrench.
Assembling the Exercise Bike Making Sure the Unit Is Stable Make sure the unit is level before allowing anyone to use it. CAUTION: To eliminate movement, make sure the adjustable feet are in contact with the floor. To level the unit: Gently rock the unit.
The equipment usually returns to smooth operation after a day or two of normal use. If it does not, contact your dealer for assistance. For more information, refer to Obtaining Service. Assembling and Maintaining the UBK 815 Upright Exercise Bike...
Installing the Console Before you begin, make sure that the cables have been fed through the mounting bracket and their ends extend through the round opening at the base of the bracket. The television cable, along with any audio, video, or power cables needed to support a Cardio Theater screen or receiver, should be fed through the bracket and should extend through the opening at its upper end.
Page 26
Tighten the screws completely using a Assembling and Maintaining the UBK 815 Upright Exercise Bike -inch x -inch buttonhead screws through -inch hex wrench.
Page 27
Installing the Console 4. Route the twisted, red-and-black heart rate sensor cable and the flat, gray base unit data cable to the left of the mounting bracket and about three-quarters of the way up the left side of the console, as shown in the following illustration.
Page 28
Figure 12: Rear cover position 8. Position the back cover and attach the four 1-inch panhead machine screws, then tighten the screws completely using a #2 Phillips screwdriver. Figure 13: Reattaching rear cover screws Assembling and Maintaining the UBK 815 Upright Exercise Bike...
To keep the equipment functioning properly, perform the minor maintenance tasks in this section at the intervals shown on the maintenance checklist. Failure to maintain the equipment as described in this section could void the Precor Limited Warranty. DANGER Daily Cleaning Precor recommends that you clean the equipment before and after each exercise session.
CAUTION: Read and follow the manufacturer’s instructions, particularly dilution instructions, before using any cleaner on Precor fitness equipment. Do not use concentrated cleaners at full strength, or acidic cleaners of any kind; such cleaners weaken the protective finish on the equipment and void the Precor Limited Warranty.
Maintenance Quarterly Maintenance Precor recommends that you clean and inspect the equipment more thoroughly once every three months. To perform quarterly maintenance: Remove the cover panels. 2. Vacuum out any debris, being careful not to bring the vacuum cleaner nozzle too close to any circuit board (unless your vacuum cleaner is protected against static buildup).
If it has an optional power adapter, connect the adapter to prevent damage to the internal battery. Position it so that it will not become damaged and will not interfere with people or other equipment. Assembling and Maintaining the UBK 815 Upright Exercise Bike...
Self-Powered Features Important: This chapter of the manual describes Precor fitness equipment that can operate without being connected to AC power. This includes units equipped with P40 or P20 consoles. However, P80 consoles must be connected to AC power through their power supplies to operate.
Loss of user and program information after the user stops exercising, without any display of a workout summary or a notification of pending shutdown Important: To maintain a constant power source, use the optional power adapter. Assembling and Maintaining the UBK 815 Upright Exercise Bike...
CAUTION: The internal cable kit must be installed by authorized service personnel. Do not attempt installation on your own as you could void the Precor Limited Warranty. For more information, refer to Obtaining Service. Important: If this equipment includes a P80 console, the optional...
Refer to Obtaining Servic CAUTION: The battery stored inside the equipment contains hazardous materials and must be disposed of according to Hazardous Waste Regulations. Refer to Hazardous Materials and Proper Disposal. Assembling and Maintaining the UBK 815 Upright Exercise Bike...
CONDITIONS. Limited Warranty. Precor Incorporated warrants all new Precor products to be free from defects in materials and manufacture for the warranty periods set forth below. The warranty periods commence on the invoice date of the original purchase. This warranty applies only against defects discovered within the warranty period and extends only to the original purchaser of the product.
Page 38
GIVEN ABOVE FOR THOSE SAME PARTS. PRECOR HEREBY DISCLAIMS AND EXCLUDES THOSE WARRANTIES THEREAFTER. Some States do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. PRECOR ALSO HEREBY DISCLAIMS AND EXCLUDES ALL OTHER OBLIGATIONS OR LIABILITIES,...
Page 39
Commercial Equipment Limited Warranty Exclusive Remedies. For any product described above that fails to conform to its warranty, Precor will provide, at their option, one of the following: (1) repair; (2) replacement; or (3) refund of the purchase price. Precor Limited Warranty service may be obtained by contacting the authorized dealer from whom you purchased the item.
Page 40
Assembling and Maintaining the UBK 815 Upright Exercise Bike Notes:...
Page 49
Important Safety Instructions Safety Precautions Always follow basic safety precautions when using this equipment to reduce the chance of injury, fire, or damage. Other sections in this manual provide more details of safety features. Be sure to read these sections and observe all safety notices.
Page 50
350 pounds (160 kg). Use the equipment only for its intended purpose as described in this manual. Do not use accessory attachments that are not recommended by Precor. Such attachments may cause injuries. Do not operate the equipment where aerosol (spray) products are being used or where oxygen is being administered.
Page 51
The batteries within self-powered equipment contain materials that are considered hazardous to the environment. Federal law requires proper disposal of these batteries. If you plan to dispose of your equipment, contact Precor Commercial Products Customer Support for information regarding battery removal. Refer to Obtaining Service.
Page 52
The regulatory information in this section applies to the exercise equipment and its control console. Safety Approvals for Cardiovascular Equipment Precor equipment has been tested and found to comply with the following applicable safety standards. Cardiovascular Type Equipment: CAN/CSA, IEC, EN 60335-1 (Household and similar...
Page 53
Precor authorized dealer. Precor exercise equipment that is connected to an external power circuit, such as treadmills or equipment with optional power supplies for self-powered equipment, must be properly grounded.
Page 54
Do not attempt to service the equipment except for maintenance tasks. If any items are missing, contact your dealer. For more information regarding customer support numbers or a list of Precor authorized service centers, visit the Precor web site at http://www.precor.com. Product Owner's Manual...
Page 55
Table of Contents Edition Information ... 2 Trademark Note ... 2 Intellectual Property Notice ... 2 Important Safety Instructions ... 3 Safety Precautions ... 3 Hazardous Materials and Proper Disposal ... 5 Product Recycling and Disposal ... 5 Regulatory Notices for Cardiovascular Exercise Equipment ...
Product Features This section is designed to show you how to customize the equipment for your users and view useful product information. All these features remain hidden to the users and can only be accessed using special keypresses. These custom settings allow you to Change the display to a different language Change the display to show U.S.
Page 58
All * All * All * All * All * Bike * This feature is available in all Precor fitness equipment. Note: When you make changes in the programming mode, the new settings replace the factory defaults. Factory Prompt Default...
You must be in the Programming mode before you can change the settings. To access the programming mode: At the Precor banner, press the following keys in sequence without pausing between selections: RESET, 5, 6, 5, 1, 5, 6, 5 Note: A PAUSE/RESET key appears on some products and functions the same as the RESET key.
Page 61
Navigational arrows: Move you through the menu and can also be used to increase or decrease time units. Press to choose or accept the displayed selection. Returns user to the previous menu level without saving changes. Exits Programming mode and returns to the Precor banner.
Page 62
Use the following flowchart to navigate through the menu settings. Figure 4: Bike menu settings Choosing a Language The equipment can display user prompts, text, and user entries in several different languages. When the equipment is shipped from the factory, the default language is English. Note: Programming prompts are not affected by language selection.
Page 63
Product Features Selecting a U.S. Standard or Metric Display The equipment can display measurements in either Metric or U.S. Standard. The default factory setting is U.S. Standard. To change the display measurement: At the S E L E C T U N I T S prompt, press OK. Use the navigational arrow keys to select a unit of measure (U S or M E T R I C ).
Page 64
1 and 120 seconds (two minutes). For example, if you set a pause time limit of 60 seconds, the display automatically resets to the Precor banner if no movement is detected and no key press occurs for one minute.
Product Features Setting a Resistance Range The bike resistance levels are low, medium, and high. Within each setting, 25 levels of resistance are available, but the chosen setting affects the overall resistance range. To set a resistance range: At the S E T R E S I S T A N C E R A N G E prompt, press OK and use the navigational arrow keys to choose L O W , M E D I U M or H I G H (L O , M E D , or H I on some equipment).
In general, you would only access this information if directed to do so by Precor Customer Support. To navigate through the informational displays, use the following flowchart. A table located after the flowchart provides more information about each more display.
Page 67
Product Features Note: The CLEAR key is located on the number keypad. If your product has a PAUSE/RESET key, use it in place of the RESET key called out in the flowchart. Figure 5: Informational settings...
Page 68
Table 4. Informational Displays for all products Product Display H O U R M E T E R U - B O O T S W U - B A S E S W L O W E R S W S E R .
Page 69
To view the error log: At the Precor banner, press and hold RESET for 4 seconds. 2. If D I A G S - I N F O R M A T I O N D I S P L A Y or E R R O R L O G appears, then press OK.
Page 70
Important: You cannot retrieve the error log once you have deleted it. You may want to resolve any issues you are experiencing with the equipment before erasing the error log. 4. Press RESET to return to the Precor banner. Product Owner's Manual...
Educating Users This console offers an easy-to-follow display and multiple programs to help users meet their workout needs. The keypad lets them select data and control their workout session and SmartRate® provides a visual aid that monitors heart rate and workout intensity at a glance.
Important: If you tilt the seat too far forward, it will restrict the function of the seat height adjust handle. Using SmartRate® The Precor SmartRate® technology is a precise, easy-to-read heart rate monitor that helps users achieve their best personalized workouts. SmartRate displays actual heart rate information in relation to the user’s target zone for weight...
Display Console The display console is designed for ease of use. Use the following graphic and table to learn more about the console displays. Figure 8: Console parts PROGRAMS PROGRAMS HEART MANUAL RATE INTERVAL WEIGHT LOSS VARIETY PERFORMANCE TIME ELAPSED TIME REMAINING CALORIES QUICK...
Page 74
Distance, Stride, or Average Speed. An indicator light appears next to the item that is displayed. Pause/Reset key: Press the key once to pause the equipment and twice to return to the Precor banner. QUICKSTART: Press to begin your workout immediately. Product Owner's Manual...
Page 75
Display Console Using the Upper Display The program profile supplies information about your programmed workout. A blinking segment in the profile indicates your position. The profile raises or lowers if you change your resistance. Column height Figure 9: Parts of the program profile CrossRamp or Resistance settings 17 —...
Page 76
Keypads Use the keypads to enter program selections and display preferences. Multiple keypads exist on the console display including a navigational keypad in the center of the display, and a PROGRAMS keypad. PROGRAMS Keypad MANUAL INTERVAL VARIETY Figure 10: Programs Keypad The PROGRAMS keypad provides access to all the exercise programs.
Page 77
Display Console Number Keypad The number keypad has several functions depending on what is connected to the equipment. CLEAR Figure 11: Number keypad Table 7. Connections Connection Computer (CSAFE compatible) Entertainment Option Unconnected ENTER Description If a computer is attached to the CSAFE connection on the equipment, the number keypad lets you enter your user ID and answer other setup prompts.
Page 78
Product Owner's Manual The CLEAR and ENTER keys provide the following functions: CLEAR: Use the CLEAR key to remove the last number being displayed. ENTER: Use the ENTER key to accept the number being displayed. Note: The OK and ENTER keys are usually interchangeable and provide the same function when no peripheral devices are attached to the equipment.
Workout Options CAUTION: Before beginning any fitness program, see your physician for a complete physical examination. Know your physician-recommended heart rate target zone. To begin your workout: Face the display. 2. Hold on to a handlebar and step on the foot pedals. 3.
Page 80
Choosing QUICKSTART Use the Quickstart feature to begin an immediate workout. To use this feature: Begin pedaling. 2. While the Precor banner scrolls, press QUICKSTART to begin the Manual Program. Figure 12: QUICKSTART button QUICKSTART applies the following defaults: Prompts Default Value...
Page 81
Note: To change a value (program, time, weight, or age) that you have already entered, continue pedaling and press RESET to return to the Precor banner. Select a program and reenter the appropriate values. 4. Maintain a comfortable and consistent RPM while exercising.
Page 82
Note: If the display is blank, you will need to maintain the minimum rate of motion to supply power. If the Precor banner appears, the equipment is not connected to a computer. If the equipment is connected to a computer, the following...
Page 83
Workout Options Changing Programs in Mid-session You can change programs in the middle of a session by selecting a new program from the PROGRAMS key menu and pressing OK. All accumulated statistics are transferred to the new program as you continue exercising. Certain programs, such as Basic HRC and Weight Loss, are not available for mid-session transfers due to set goals and program preferences.
Page 84
Note: If the optional power adapter is attached, you do not have to continue the minimum rate of motion to view your workout statistics. When you complete the cool down period, the workout summary appears. When you are ready, press RESET to return to the Precor banner. Product Owner's Manual...
Programs This section describes the programs available on the equipment. Use the following table to learn more about each workout program. Graphic Chapter Program Workout Details Heading Manual This workout begins as a flat line. You can increase or decrease the resistance using the resistance key.
Page 86
Graphic Program Workout Details Heading Heart Rate Use these programs to set a target for your heart rate. The workouts adjust the resistance to maintain your heart rate within two beats per minute of the target heart rate while you exercise.
Page 87
Programs Program Tips Begin at the Precor banner and choose a program by pressing a PROGRAMS key or QUICKSTART. While exercising, you need to sustain your exercise motion. Stopping any movement causes the equipment to shut down to conserve battery power.