Subscribe to Our Youtube Channel
Related Manuals for Lanner LEC-2055
Summary of Contents for Lanner LEC-2055
- Page 1 Embedded & Industrial Computing Hardware Platforms for Embedded and Industrial Computing LEC-2055 Preliminary User's Manual Publication date:2011-08-10 >>...
-
Page 2: Copyright And Trademarks
Resource Website accordance with the instruction manual, may cause harmful interference to radio communications. Operation Lanner http://www.lannerinc.com of this equipment in a residential area is likely to cause harmful interference in which case the user will be required Product Resources http://assist.lannerinc.com to correct the interference at his own expense. -
Page 3: Table Of Contents
TTaTTable of Contentsbeable of Conten Chapter 1: Introduction System Specification ......... . . 4 Package Contents . -
Page 4: Chapter 1: Introduction
Chapter 1 Introduction Chapter 1: Introduction System Specification Thank you for choosing the LEC-2055. The LEC-2055 is an ultra-compact and robust embedded system which comes with a Mini-PCIe socket with a SIM card reader to LEC 2 Series LEC-2055 enable 3G networks as well as GPS capability. -
Page 5: Package Contents
Chapter 1 Introduction Package Contents Your package contains the following items: LEC-2055 Fanless Embedded System • Serial-ATA/Power Cable (P/N: 080W1N0002001) • Drivers and User’s Manual CD (P/N: S09OADA01H100) • 2-pin Female Terminal Block (04AW20021E101) • Embedded and Industrial Computing... -
Page 6: Chapter 2: System Components
Chapter 2 System Components Chapter 2: System Components System Drawing Mechanical dimensions of the LEC-2055 Unit: mm Embedded and Industrial Computing... -
Page 7: System Components
Chapter 2 System Components Block Diagram The block diagram depicts the relationships among the interfaces and modules on the motherboard.. Processor ATOM N270 Intel DDR2 400/533MHz SO-DIMM 945GSE SATA-II SATA GbE LAN PCIe x2 2x RJ-45 Connector 2x RTL8111D Intel Mini PCI Express PCIe SIM Card Reader... -
Page 8: Front Components
Chapter 2 System Components Front Components Component Description Pin Definition Reference F1 HDD (Yellow) and POWER LED & Hard Disk LED (LED2) on page 16 • Blinking: data access activities Power LED (Green) • Off: no data access activities Power •... -
Page 9: Rear Components
R4 DC-In (power) LEC-2055 support power range DC_IN Connector (CON1) on between 12V and 36V. page 16 Note: Antenna is not included in the standard package. You can purchase it from Lanner separately as an accessory. Embedded and Industrial Computing... -
Page 10: Chapter 3: Board Layout
Chapter 3 Board Layout Chapter 3: Board Layout External Connectors The following picture highlights the location of system input/output connectors. Refer to the table 3.1 Connector List for more details. LANB1/LANB2 USB1 COM1 COM2 LED2 CON1 Embedded and Industrial Computing... -
Page 11: Internal Connectors And Jumpers
Chapter 3 Board Layout Internal Connectors and Jumpers The following picture highlights the location of internal connectors and jumpers. Refer to the table 3.1 Connector List for more details. PCOM2 PCOM1 USBB1 DLPC1 VGA1 PS4S1 ATNC1 JSPIROM1 COMB1 CCMOS1 DIMM1 SATA1 USIM1 LEB-2055... -
Page 12: Connectors And Jumpers List
Chapter 3 Board Layout Connectors and Jumpers List The tables below list the function of each of the board jumpers and connectors by labels shown in the above section. The next section in this chapter gives pin definitions and instructions on setting jumpers. Table 3.1 Connector List for LEB-2055 Labels Function... -
Page 13: Jumper Settings
Chapter 3 Board Layout Jumper Settings COM Protocol RS-232 RS-422 RS-485 Setting LEB-2055 Selector 1 1 ON 1 OFF 1 OFF 2 OFF 2 ON 2 OFF Selector 2 Serial-ATA Connector (SATA1): It is for connecting a 2.5’’ 3 OFF 3 OFF 3 ON Selector 3... - Page 14 Chapter 3 Board Layout LAN Ports (LANB1/LANB2): Pin No. Pin Name Pin No. Pin Name CE1# CE3# Pin No. Description Fast Ethernet Gigabit Ethernet IOR# BI_DA+ IOW# BI_DA- BI_DB+ IDEIRQ BI_DC+ VCC3 VCC3 BI_DC- CBSEL# BI_DB- RESET# BI_DD+ IORDY BI_DD- DREG DACK# Clear CMOS jumper (CCMOS1): It is for clearing the...
- Page 15 Chapter 3 Board Layout DC_IN CONNECTOR (CON1): A Phoenix connector for Mini PCI Express Connector (MPCIE1): external power supply. Pin Name Pin Name WAKE# SMB_CLK +3.3V PETn0 Pin No. Pin Name SMMB_DATA DC_IN PETp0 +1.5V SIM Card Socket (USIM1): CLKREQ# USB_D- UIM_PWR RSVERD...
-
Page 16: Chapter 4: Hardware Setup
AC power is removed. Installing a CompactFlash Card Unpower the LEC-2055 and remove the power cord. LEC-2055 provides one CompactFlash slot. Follow the Turn the device upside down. procedures bellow for installing a CompactFlash card. -
Page 17: Wireless Module Installation
Chapter 4 Hardware Setup Wireless Module Installation Align the wireless module’s cutout with the Mini-PCIe slot notch. Insert the wireless module into the connector diagonally. Push the other end of the wireless module to be tightened with the latch. 3G SIM Card Installation In order to insert the SIM card, you will have to take off the front panel first. -
Page 18: Installing The Hard Disk
Hardware Setup Installing the Hard Disk Connecting Power Connect the LEC-2055 to a 12~36 VDC power source. The system can accommodate one Serial-ATA disk. Follow The DC power-in connector comes with a 2-pin terminal these steps to install a hard disk into the system: block for its Phoenix contact. -
Page 19: Wall Mounting
Hardware Setup Wall Mounting The product does not ship with wall mounting kit. You could purchase the wall mounting kit from Lanner as an accessory. To mount your product on the wall, follow the instructions below: First make a hole for the anchor in the surface on the wall. -
Page 20: Appendix F: Programming Watchdog Timer
For sample watchdog code, see watchdog folder under LEC-2055 Utility on the Driver and Manual CD printf(“\t\t Lanner Electronics Inc. 2010-01- 06\n”); printf(“\t\t Watchdog timer reset for VES-403\ n\n”);... - Page 21 Appendix F Programming Watchdog Timer delay(10); write_w83627uhg_reg(0x08, 0xf6, 0x00); printf(“\t\t Lanner Electronics Inc. 2010-01-06\n”); delay(10); printf(“\t\t Watchdog timer reset for VES-403\n\n”); init_Pin_init(); int write_w83627uhg_reg(int ldn, int reg, int value) time = atoi(argv[1]); outportb(index_port,0x07); delay(10); printf(“\t\t Setting WatchDog time out for System outportb(data_port, ldn);...
-
Page 22: Appendix G: Terms And Conditions
Appendix G Terms and Conditions Appendix G: RMA Service Terms and Conditions Requesting a RMA# To obtain a RMA number, simply fill out and fax the “RMA Request Form” to your supplier. Warranty Policy The customer is required to fill out the problem code as listed. - Page 23 Appendix G Terms and Conditions RMA Service Request Form When requesting RMA service, please fill out the following form. Without this form enclosed, your RMA cannot be processed. Reasons to Return: Repair(Please include failure details) RMA No: Testing Purpose Company: Contact Person: Phone No.
Need help?
Do you have a question about the LEC-2055 and is the answer not in the manual?
Questions and answers