Do you have a question about the RT112C and is the answer not in the manual?
Questions and answers
Scott
May 19, 2025
Can I replace the string with metal blade cutter.
1 comments:
Mr. Anderson
May 24, 2025
No. The Weed Eater RT112C is designed to use only 0.065 inch (1.65 mm) diameter line. Using other materials such as wire or metal blades is not recommended and can cause serious injury.
This answer is automatically generated
Bob
March 31, 2025
Where does the nut go
1 comments:
Mr. Anderson
March 31, 2025
The specific location where the nut goes on the Weed Eater RT112C is not clearly stated in the provided context. The nut is described as being sold individually, made of metal, and having multiple potential applications depending on the equipment, but no exact placement or function on the RT112C model is specified.
Page 1
Bien lire les instructions avant d’assembler l’outil. Tout défaut de le faire pourrait entraîner des blessures graves. WEED EATER 1030 Stevens Creek Road Augusta, GA 30907 Trademark Instruction Manual RT112C WEED EATER 5855 Terry Fox Way Mississauga, Ontario L5V 3E4 545117537 8/8/06...
Close attention is necessary when used near children. DANGER: Never use blades or flail- ing devices. Unit is designed for line trimmer use only. Use of any other accessories or at- tachments will increase the risk of injury. WARNING: Trimmer line throws ob- jects violently.
(see USER RE- PLACEABLE SERVICE PARTS in the SERVICE AND ADJUSTMENTS section). Never use wire, rope, string, etc. S Use specified trimmer spool. Make sure spool is properly installed and all parts are securely fastened. S Use only WEED EATER replacement parts and accessories as recommended.
ASSEMBLY WARNING: If received assembled, review all assembly steps to ensure your unit is properly assembled and all fasteners are secure. TUBE ASSEMBLY Upper Locking Sleeve Assembly Wires Lower Locking Sleeve Assembly 1. Align upper tube groove with triangle on lower locking sleeve assembly.
ASSIST HANDLE The ASSIST HANDLE is used to help hold and guide the unit. TRIMMER HEAD The TRIMMER HEAD holds cutting line and rotates during operation. TAP BUTTON The TAP BUTTON is used to advance the cutting line during operation and to remove...
The scalping technique removes unwanted vegetation down to the ground. Hold the bot- tom of the trimmer head about 3 inches (8 cm) above the ground and at an angle. Allow the tip of the line to strike the ground around trees, posts, monuments, etc.
The fanning action of the rotating line can be used for a quick and easy clean up. Keep the line parallel to and above the surfaces being swept and move the tool from side to side. MAINTENANCE WARNING: Disconnect unit from the power source before performing mainte- nance.
REPLACEMENT PART Spool with 0.065″ Trimmer Line Assist Handle Bolt Carriage, 1/4-20 Wing Nut Shield Assembly STORAGE WARNING: Perform the following steps after each use. Stop the unit and disconnect the power source when not in use. Carry the unit with motor stopped.
LIMITED WARRANTY WEED EATER warrants to the original pur- chaser that each new WEED EATER brand electric or cordless product is free from de- fects in material and workmanship and agrees to repair or replace under this war- ranty any defective WEED EATER brand electric product within two (2) years from the original date of purchase.
Need help?
Do you have a question about the RT112C and is the answer not in the manual?
Questions and answers
Can I replace the string with metal blade cutter.
No. The Weed Eater RT112C is designed to use only 0.065 inch (1.65 mm) diameter line. Using other materials such as wire or metal blades is not recommended and can cause serious injury.
This answer is automatically generated
Where does the nut go
The specific location where the nut goes on the Weed Eater RT112C is not clearly stated in the provided context. The nut is described as being sold individually, made of metal, and having multiple potential applications depending on the equipment, but no exact placement or function on the RT112C model is specified.
This answer is automatically generated
can i replace this motor?