Daily Care And Maintenance - Xiaomi M365 Instruction Manual

8. Daily care and maintenance

Cleaning and storage for electric scooter
If there are dirt and stains on the surface of the electric scooter, use soft cloth dipped with clean water to wipe the dirt; if the
dirt and stains are hard to be cleaned, coat some toothpaste on dirty place, use the brush to brush repeatedly, and use wet
close to clean. If the plastic part has scratches, use abrasive paper or other abrasive materials for polishing.
Note: do not clean the body by using alcohol, petrol, kerosene or other chemical solvent with corrosion and volatility, or other-
wise it will damage the appearance of body and internal structure seriously. Prohibit using pressure water gun for spraying and
washing; when cleaning the electric scooter, be sure that the electric scooter is under off condition, the charging cable has
been pulled up and the rubber plug at the charging mouth is covered tightly, or otherwise you may get an electric shock or the
scooter may have serious fault since water is entering.
When the electric scooter is not used, keep the electric scooter at day and shady indoor place as far as possible and avoid
putting it outdoors for long time. Exposure to sunlight/overheated/subcooled outdoor environment will fasten the aging for the
appearance and tire of electric scooter or reduce the service life of the electric scooter and battery.
Maintenance for battery of the electric scooter
1. Do not use battery of other model or brand, or may cause safety risks.
2. Prohibit touching the contacts of battery, disassembling or puncturing the shell. Avoid metal products touching the contacts
of battery and then cause short circuit; otherwise, it may cause damage of battery or even casualties.
3. Only use original charger for charging, or otherwise the battery may be damaged or got fired.
4. Improper dealing with wasted or old battery may cause environmental pollution seriously. Please follow local rules to dispose
this wasted battery. Do not throw the battery away freely and jointly protect the natural environment.
5. Please charge the battery in full after every time use and then store it, which is good for extending the service life of battery.
Do not put the battery under high temperature environment over 50℃ or low temperature environment lower than -20℃ (for
example, do not put the electric scooter or the battery in the car that is exposed in the air in summer); do not throw the battery
into fire, otherwise the battery may be invalid, overheated or even got fired. If the electric scooter is not used for more than 30
days, please charge the battery in full and store the scooter under cool and dry indoors, and charge the battery in full every 60
days, otherwise the battery may be damaged, and such damage is not under the range of warranty.
Avoid charging the scooter when the power is used up, and charge the electric scooter after every time use, which can greatly
extend the service life of battery. What' s more, use the electric scooter under normal temperature, the battery may have better
endurance mileage and property; use the electric scooter under 0℃, the endurance and performance of battery may be
decreased. Under typical condition and -20℃ environment, the endurance mileage of battery may be half or less of it under
normal temperature condition. When the temperature is getting back, the endurance ability of battery will be recovered, and
see the display of residual mileage stipulated in the APP.
Note: the electric scooter that is charged in full will use up the storage power for about 120-180 days under standby mode.
There is intelligent chip in the battery to record down the charging situation of the battery, and the battery can' t be charged if it
is damaged due to non charging for a long time; if the battery is not charged at the time, the battery may be damaged due to
over discharge, and such damage can' t be recovered, and the battery can' t be repaired for free under such condition. (note:
non professionals are prohibited disassembling the battery freely, otherwise it may cause serious safety accidents due to
electric shock or short circuit)
13
Disc brake debugging
If you feel that the brake is too tight, use M5 hexagon wrench to loosen the tension disc screw on disc brake seat from
counter-clockwise direction, send back the brake line and slightly shorten the exposed line, and then tightly lock the
tension disc screw; if you feel that the brake is too loose, loosen the tension disc screw, pull out the brake line to let the
exposed line be longer, and then tightly lock the tension disc screw.
Handlebar shaking debugging
If the handlebar of electric scooter is shaking during the riding period, please use M5 hexagon wrench to tighten the two
screws at the place of folding mechanism.
Use of extended charging connector
If the front and back wheels of your electric scooter are lack of air, please use the complementary extended charging connec-
tor to connect to the air jet of the tire for pumping up. Screw off the mouth of air jet of front and back tire firstly, tighten the
extended charging connector with the air jet of tire, and connect to the inflator for pumping up after tightening.
Brake cable
14