Mitsubishi Electric F700 Instruction Manual page 189

Communication operation and setting
(6) Modbus registers
System environment variable
Register
40002 Inverter reset
40003 Parameter clear
40004 All parameter clear
40006 Parameter clear
40007 All parameter clear
40009 Inverter status/control input instruction
40010 Operation mode/inverter setting
40014 Running frequency (RAM value)
40015 Running frequency (EEPROM value)
*1 The communication parameter values are not cleared.
*2 For write, set the data as a control input instruction. For read, data is read as an inverter operating status.
*3 For write, set data as the operation mode setting. For read, data is read as the operation mode status.
<Inverter status/control input instruction>
Bit
Control input instruction
0 Stop command
1 Forward rotation command
2 Reverse rotation command
3 RH (high speed operation command)
4 RM (middle speed operation command)
5 RL (low speed operation command)
6 JOG (Jog operation)
7 RT (second function selection)
8 AU (current input selection)
9 (selection of automatic restart after
instantaneous power failure)
10 MRS (output stop)
11 STOP (start self-holding)
12 RES (reset)
13
14
15
*1 The signal within parentheses is the initial setting. The description changes depending on the setting of Pr. 180 to Pr. 189 (input
terminal function selection) (page85).
Each assigned signal is valid or invalid depending on NET. (Refer to page 151)
*2 The signal within parentheses is the initial setting. The description changes depending on the setting of Pr. 190 to Pr. 196 (output
terminal function selection) (page91).
Real-time monitor
Refer to page 100 for details of the monitor description.
Register Description
40201 Output frequency
40202 Output current
40203 Output voltage
40205 Frequency setting
40206 Running speed
40208 Converter output voltage
40209 Regenerative brake duty
Electronic thermal relay function
40210
load factor
40211 Output current peak value
40212 Converter output voltage peak value
40213 Input power
*1 Input terminal monitor details
b15
  
*2 Output terminal monitor details
b15
  
*3 The setting depends on capacities. (01160 or less/01800 or more)
182
Definition
*1
*1
*3
Definition
*1
*1
IPF (instantaneous power failure)
*1
*1
*1
*1
CS
*1
*1
*1
*1
0
0
0
Unit
0.01Hz
0.01A/0.1A
0.1V
0.01Hz
1r/min
0.1V
0.1%
0.1%
0.01A/0.1A
0.1V
0.01kWh/
0.1kWh

CS RES STOP
   
Read/write
Write Any value can be written
Write Set H965A as a written value.
Write Set H99AA as a written value.
Write Set H5A96 as a written value.
Write Set HAA99 as a written value.
Read/write See below.
*2
Read/write See below.
Read/write According to the Pr. 37 and Pr. 144 settings,
the frequency and selectable speed are in
Write
1r/min increments.
Inverter status
RUN (inverter running)
*2
Forward rotation
Reverse rotation
SU (up to frequency)
*2
OL (overload)
*2
FU (frequency detection)
*2
ABC1 (alarm)
*2
)
ABC2 (
*2
0
0
0
0
0
0
Alarm occurrence
Register
40214 Output power
*3
40215 Input terminal status
40216 Output terminal status
40217 Load meter
40220 Cumulative energization time
40223 Actual operation time
40224 Motor load factor
40225 Cumulative power
40250 Power saving effect
*3
40251 Cumulative saving power
40252 PID set point
40253 PID measurement value
*3
40254 PID deviation value
MRS JOG RH RM
 
ABC2 ABC1
Remarks
<Operation mode/inverter setting>
Read
Mode
value
EXT H0000
PU H0001
EXT
H0002
JOG
NET H0004
*2
PU+
H0005
EXT
The restrictions depending on the
operation mode changes according
to the computer link specifications.
Description
*1
*2
RL RT AU
FU OL IPF
Written
value
H0010


H0014

Unit
0.01kWh/
0.1kWh
*3


0.1%
1h
1h
0.1%
1kWh
Variable
Variable
0.1%
0.1%
0.1%
b0
STR STF
b0
SU RUN