TP-Link JetStream T1500-28TC Installation Manual
Hide thumbs
Also See for JetStream T1500-28TC:
- Installation manual (24 pages) ,
- Installation manual (20 pages)
Related Manuals for TP-Link JetStream T1500-28TC
Summary of Contents for TP-Link JetStream T1500-28TC
-
Page 1: Installation Guide
Business Networking Solution Installation Guide JetStream Smart Switch T1500-28TC/T1500-28PCT... - Page 2 Conventions • Some models featured in this guide may be unavailable in your country or region. For local sales information, visit http://www.tp-link.com. • The figures in Chapter 2 to Chapter 4 are for demonstration purposes only. Your switch may differ in appearance from that depicted.
-
Page 3: Table Of Contents
Contents Chapter 1 Introduction ——————————— 01 Product Overview ............01 Appearance ...............01 Chapter 2 Installation ——————————— 06 Package Contents ............06 Safety Precautions ............06 Installation Tools ..............08 Product Installation ............09 Chapter 3 Lightning Protection ——————— 11 Cabling Reasonably............11 Connect to Ground ............13 Chapter 4 Connection ———————————... -
Page 4: Chapter 1 Introduction
JetStream Smart Switch Chapter 1 Introduction Product Overview T1500-28TC/T1500-28PCT is compliant with the IEEE802.3 Ethernet protocols. T1500-28TC/T1500-28PCT is equipped with powerful management interface, via which system, port, network, VLAN and priority can be configured. They provide a variety of service features and multiple powerful functions with high security. The EIA-standardized framework and smart configuration capacity can provide flexible solutions for a variable scale of networks. - Page 5 JetStream Smart Switch LEDs Status Indication The switch is powered on The switch is powered off or power supply is abnormal Flashing Power supply is abnormal Flashing The switch works properly On/Off The switch works improperly A device is connected to the corresponding port but no activity 10/100M Flashing...
- Page 6 JetStream Smart Switch The front panel of T1500-28PCT is shown as the following figure. Figure 1-2 Front Panel of T1500-28PCT SFP Port 10/100/1000Mbps LEDs LED Mode Reset 10/100Mbps RJ45 RJ45 Port Switch Button Port and PoE Port LEDs T1500-28PCT has an LED mode switch button which is for switching the LED status indication.
- Page 7 JetStream Smart Switch A 1000Mbps device is connected to the corresponding port, but no activity Green Flashing Data is being transmitted or received 1000M A 10/100Mbps device is connected to the corresponding port, but no activity Yellow Flashing Data is being transmitted or received No device is connected to the corresponding port When the PoE LED is on, the port LED is indicating the power supply status.
- Page 8 JetStream Smart Switch 10/100/1000Mbps RJ45 Port Designed to connect to the device with a bandwidth of 10Mbps, 100Mbps or 1000Mbps. Each has a corresponding 1000M LED. SFP Port Designed to install the SFP module. T1500-28PCT features some SFP transceiver slots that are shared with the associated RJ45 ports. The associated two ports are referred as a "Combo"...
-
Page 9: Chapter 2 Installation
JetStream Smart Switch Chapter 2 Installation Package Contents Make sure that the package contains the following items. If any of the listed items is damaged or missing, please contact your distributor. One Switch This Installation Guide One Power Cord One Resource CD Two mounting brackets and the fittings Safety Precautions... - Page 10 JetStream Smart Switch Temperature/Humidity 40℃ 0℃ Please keep a proper temperature and humidity in the equipment room. Too high/ low humidity may lead to bad insulation, electricity leakage, mechanical property changes and corrosions. Too high temperature may accelerate aging of the insulation materials and can thus significantly shorten the service life of the device.
-
Page 11: Installation Tools
JetStream Smart Switch Lightening Protection Extremely high voltage currents can be produced instantly when lightning occurs and the air in the electric discharge path can be instantly heated up to 20,000℃. As this instant current is strong enough to damage electronic devices, more effective lightning protection measures should be taken. -
Page 12: Product Installation
JetStream Smart Switch Product Installation Desktop Installation ■ To install the device on the desktop, please follow the steps: 1. Set the device on a flat surface strong enough to support the entire weight of the device with all fittings. 2. - Page 13 JetStream Smart Switch Figure 2-3 Rack Installation Rack Caution: Please set 5~10cm gaps around the device for air circulation. ■ Please avoid any heavy thing placed on the device. ■ Please mount devices in sequence from the bottom to top of the rack and ensure a ■...
-
Page 14: Chapter 3 Lightning Protection
JetStream Smart Switch Chapter 3 Lightning Protection Cabling Reasonably In the actual network environment, you may need cable outdoors and indoors, and the requirements for cabling outdoors and indoors are different. A reasonable cabling system can decrease the damage of induced lightning to devices. Note: It's not recommended using Ethernet cables outdoors. -
Page 15: Requirements For Cabling Indoors
JetStream Smart Switch Requirements for Cabling Indoors ■ When cabling indoors, keep a certain distance away from the devices that may cause high-frequency interferences, such as down-conductor cable, powerline, power transformer and electromotor. The main cable should be paved in the metal raceway of the access shaft. When ■... -
Page 16: Connect To Ground
JetStream Smart Switch Min Parallel Cable Pave Way Length (mm) Parallel cabling 2~5kVA One is in the grounded metal raceway or metal pipe powerline The both are in the grounded metal raceway or metal pipe Parallel cabling >5kVA One is in the grounded metal raceway or metal pipe powerline The both are in the grounded metal raceway or metal pipe... - Page 17 JetStream Smart Switch Note: The figure is to illustrate the application and principle. The power plug you get from the ■ package and the socket in your situation will comply with the regulation in your country, so they may differ from the figure above. If you intend to connect the device to the ground via the PE (Protecting Earth) cable of ■...
- Page 18 JetStream Smart Switch Figure 3-3 Equipotential Bonding Grounding Terminal Equipotential Bonding Cable Ground Cable Grounding Bar When equipotential bonding, please note that the cable should be copper wrapped Kelly with its area being 6mm at least. The shorter cable the better, and use a grounding bar to establish an equipotential bonding point.
- Page 19 JetStream Smart Switch Install signal lightning arrester near the protected device and connect it to the ground ■ via a shorter ground cable. Figure 3-4 Equipotential Bonding Grounding Terminal Equipotential Bonding Cable Ethernet Cable Signal Lightning Arrester Device Note: Signal lightning arrester is not provided with our product. If needed, please self purchase it.
-
Page 20: Chapter 4 Connection
JetStream Smart Switch Chapter 4 Connection Ethernet Port Connect a Ethernet port of the switch to the computer by RJ45 cable as the following figure shows. Figure 4-1 Connecting the RJ45 Port RJ45 Port RJ45 Cable Verify Installation After completing the installation, please verify the following items: There are 5~10cm of clearance around the sides of the device for ventilation and the ■... -
Page 21: Initialization
JetStream Smart Switch Figure 4-2 Connecting to Power Supply Note: The figure is to illustrate the application and principle. The power plug you get from the package and the socket in your situation will comply with the regulation in your country, so they may differ from the figure above. Initialization After the device is powered on, it begins the Power-On Self-Test. -
Page 22: Chapter 5 Login To The Switch
JetStream Smart Switch Chapter 5 Login to the Switch Configure the Switch via GUI 1. To access the GUI of the switch, open a web browser and t ype the default management address http://192.168.0.1 in the address field of the browser, then press the Enter key. -
Page 23: Configure The Switch Via Cli
JetStream Smart Switch Figure 5-3 Main Page of the Switch Configure the Switch via CLI You can log on to the switch and access the CLI by Logging on to the switch remotely by a Telnet connection through an Ethernet port. To log on to the switch by a Telnet connection, please take the following steps: 1. -
Page 24: Appendix A Troubleshooting
JetStream Smart Switch Appendix A Troubleshooting Q1. Why is the Link/Act LED not lit while a device is connected to the corresponding port? Please try the following: Make sure that the cable connectors are firmly plugged into the switch and the device. Make sure the connected device is turned on and works normally. -
Page 25: Appendix B Specifications
JetStream Smart Switch Appendix B Specifications Item Content IEEE802.3i, IEEE802.3u, IEEE802.3ab, IEEE802.3z, IEEE802.3ad, IEEE802.3af Standards (T1500-28PCT), IEEE802.3at (T1500-28PCT), IEEE802.3x, IEEE802.1p, IEEE802.1q, IEEE802.1x, IEEE802.1d, IEEE802.1s, IEEE802.1w 10Base-T UTP/STP of Cat. 3 or above(maximum 100m) 100Base-TX 2-pair UTP/STP of Cat. 5 or above (maximum 100m) 100Base-FX MMF SFP Module 100Base-LX10 SMF SFP Module 100Base-BX10 SMF SFP Module Transmission Medium 1000Base-T 4-pair UTP/STP of Cat. 5e or above (maximum 100m) -
Page 26: Fcc Statement
FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. -
Page 27: Bsmi Notice
BSMI Notice 安全諮詢及注意事項 • 請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。 • 清潔本產品之前請先拔掉電源線。 請勿使用液體、 噴霧清潔劑或濕布進行清潔。 • 注意防潮， 請勿將水或其他液體潑灑到本產品上。 • 插槽與開口供通風使用， 以確保本產品的操作可靠並防止過熱， 請勿堵塞或覆蓋開口。 • 請勿將本產品置放於靠近熱源的地方。 除非有正常的通風， 否則不可放在密閉位置中。 • 請不要私自打開機殼， 不要嘗試自行維修本產品， 請由授權的專業人士進行此項工作。 • 此為甲類資訊技術設備， 于居住環境中使用時， 可能會造成射頻擾動， 在此種情況下， 使用者會被要求採 取某些適當的對策。 この装置は、 クラスA情報技術装置です。 この装置を家庭環境で使用すると電波妨害を引き起こすことがあ ります。 この場合には使用者が適切な対策を講ずるよう要求されることがあります。 VCCI-A Industry Canada Statement CAN ICES-3 (A)/NMB-3(A) Explanation of the symbols on the product label Symbol Explanation... - Page 28 The products of TP-Link partly contain software code developed by third parties, including software code subject to the GNU General Public License (“GPL”). As applicable, the terms of the GPL and any information on obtaining access to the respective GPL Code used in TP-Link products are available to you in GPL-Code-Centre under (http:// www.tp-link.com/en/support/gpl/). The respective programs are distributed WITHOUT ANY WARRANTY and are subject to the copyrights of one or more authors. For details, see the GPL Code and other terms of the GPL.