Peavey IPR2 3000 Operating Manual
Hide thumbs
Also See for IPR2 3000:
- Operating manual (116 pages) ,
- Operating manual (7 pages) ,
- Operating manual (24 pages)
Related Manuals for Peavey IPR2 3000
Summary of Contents for Peavey IPR2 3000
- Page 1 IPR2 2000/3000 ™ IPR2 2000/3000 DSP ™ Power Amplifiers Operating Manual www.peavey.com...
- Page 2 ENGLISH IPR2 2000/3000 DSP ™ Power Amplifier As the name implies, the IPR2 2000 and 3000 DSP all include advanced digital signal processing. The DSP was designed to be incredibly ™ effective, yet extremely easy to use. Using unique and revolutionary advanced bass enhancement processes, the IPR2 DSP amplifiers dramatically improve the perceived level of bass in any system, using a fraction of the power that would be required with any other power amplifier.
-
Page 3: Input Attenuators
This button indicates power is connected to the amplifier by glowing dimly while the amplifier is off. When the switch is depressed, the amplifier will turn on and the switch will illuminate brightly. PEAVEY LOGO While the amplifier is off, the logo is illuminated dimly to indicate power is connected. When the amplifier is on, the logo will illuminate brightly. - Page 4 In the unlikely event of operating conditions that may potentially damage the amplifier, the circuit breaker may trip. After inspecting the cables and connections, the amplifier can be reset. If the circuit breaker trips a second time, contact the local Peavey authorized service center.
-
Page 5: Navigation Overview
Navigation Overview Once the IPR2 screen appears, you can start adjusting the DSP processor. Pressing the encoder will bring you to the main menu. ™ The encoder knob to the right of the display is used to navigate and control the DSP functions. The Channel A and B controls to the left of the display are also encoders but are dedicated to adjusting input gain for each channel. - Page 6 To select an item from the Main Menu, rotate the encoder until the cursor marks the selection you want. Press the encoder to navigate to the Sub Menu adjustment screens for that processing function. When you enter a processing function Sub Menu, the cursor will appear in the upper left corner of the screen allowing you to scroll through Sub Menu screens.
- Page 7 Unlike the other function Sub Menus, the input mode does not change until you select “Save and Apply” and return to the Main Menu. Crossover Filters, Band-Pass Filters and Polarity Set: BP Filters Independently When you enter the “XOVER” Sub Menu, you are given three options for how the band-pass filters can be set.
-
Page 8: Output Polarity
Output Polarity Output Polarity The output polarity can be inverted on either channel. Select Normal or Invert in the polarity screen. If you create a crossover with 12dB per octave filters, the high frequency output would likely need to be inverted to maintain the proper phase relationship at the crossover frequency. - Page 9 Horn EQ The Horn EQ provides a 6dB per octave high frequency boost that is sometimes required for high frequency horns. The frequency control sets the low frequency corner of the filter. To return to the Main Menu, select Discard and Exit or Save and Exit.
-
Page 10: Saving Settings
Saving Settings In the Memory Operation Sub Menu, select “Save Settings.” Select one of the four preset locations. Edit the name by rotating the cursor to select the character and pressing the encoder to step to the next position. Continue until complete. To keep the same name, press the encoder six times to step through the name edit screen. - Page 11 IPR2 2000 DSP Specification Sheet ™ Rated Watts 2ch x 2 ohms 1100 watts 20ms repetitive burst / 900 watts 1% THD both channels driven @ 1kHz. Rated Watts 2ch x 4 ohms 600 watts 20ms repetitive burst / 570 watts 1% THD / 500 watts 0.15% THD, both channels driven @ 1kHz. Rated Watts 2ch x 8 ohms 370 watts 20ms repetitive burst / 325 watts 1% THD / 270 watts 0.15% THD, both channels driven @ 1kHz.
- Page 12 IPR2 3000 DSP Specification Sheet ™ Rated Power 2ch x 2 ohms 1750 watts 20ms repetitive burst / 1450 watts 1% THD both ch. driven @ 1kHz. Rated Power 2ch x 4 ohms 950 watts 20ms repetitive burst / 900 watts 1% THD / 815 watts 0.2% THD, both ch. driven @ 1kHz. Rated Power 2ch x 8 ohms 525 watts 20ms repetitive burst / 500 watts 1% THD / 430 watts 0.15% THD, both ch.
- Page 13 Features and specifications subject to change without notice. Peavey Electronics Corporation • 5022 Hartley Peavey Drive • Meridian • MS • 39305 (601) 483-5365 • FAX (601) 486-1278 • www.peavey.com ©2013 31700092...