Table of Contents
Advertisement
Quick Links
Please do not return unit to retailer.
Por favor, no devuelva el aparato al lugar de compra.
Veuillez ne pas retourner l'outil au détaillant.
1- -800- -554- -6723
Manual de Instrucciones
1950 / 1975 / 2050 / 2055 / 2075
2150 / 2155 / 2175 / 2350 / 2375
For Occasional Use Only
WARNING:
Read and follow all Safety Rules and Operating Instructions before
using this product. Failure to do so can result in serious injury.
ADVERTENCIA:
Lea el manual de instrucciones y siga todas las advertencias e en-
strucciones de seguridad. El no hacerlo puede resultar en lesiones
graves.
AVERTISSEMENT:
Lire le manuel d'instructions et bien respecter tous les avertisse-
ments et toutes les instructions de sécurité. Tout défaut de le faire
pourrait entraîner des blessures graves.
Poulan
1030 Stevens Creek Road
Augusta, GA 30907
www.poulan.com
Instruction Manual
Manuel d'Instructions
2050WT / 2150PR
Mississauga, Ontario L5V 3E4
545123582
R
Poulan
5855 Terry Fox Way
8/25/06
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Poulan Pro 545123582
Summary of Contents for Poulan Pro 545123582
-
Page 1: Instruction Manual
Tout défaut de le faire pourrait entraîner des blessures graves. Poulan 1030 Stevens Creek Road Augusta, GA 30907 Instruction Manual 2050WT / 2150PR Poulan 5855 Terry Fox Way Mississauga, Ontario L5V 3E4 545123582 8/25/06... -
Page 2: Identification Of Symbols
IDENTIFICATION OF SYMBOLS WARNING! This chain saw can be dangerous! Care- less or improper use can cause serious or even fatal injury. Always wear appropriate ear protection, eye protection and head protection. Always use two hands when operating the chain saw. WARNING! should be avoided;... -
Page 3: Kickback Warning
S Keep the handles dry, clean, and free of oil or fuel mixture. S Keep fuel and oil caps, screws, and fas- teners securely tightened. S Use only Poulan accessories and re- placement parts as recommended. HANDLE FUEL WITH CAUTION S Do not smoke while handling fuel or while operating the saw. -
Page 4: Maintain Control
contacts a foreign object in the wood in the cut along the bottom of the guide bar and the saw chain is suddenly stopped. This sudden stopping pulls the saw forward and away from the operator and could easily cause the operator to lose control of the saw. - Page 5 with a small radius tip which reduces the size of the kickback danger zone on the bar tip. A Reduced- -Kickback Guide Bar has been demonstrated to significantly re- duce the number and seriousness of kick- backs when tested in accordance with safety requirements for gasoline powered chain saws as set by ANSI B175.1.
-
Page 6: Assembly
MODEL Length 1950/1975/ 952044368 14″ 2050/2050WT 2055/2075/ 952044370 16″ 2150/2150PR 2155/2175/ 952044418 18″ 2350/2375 NOTE: If this saw is to be used for com- mercial logging, a chain brake is required and shall not be removed or otherwise dis- abled to comply with Federal OSHA Regula- tions for Commercial Logging. -
Page 7: Chain Tension
Mount the Bar 6. Carefully remove the chain from the pack- age. Hold chain with the drive links as shown. Tip of CUTTERS MUST FACE IN DIIRECTION OF ROTATION Depth Gauge Cutters Drive Links Place chain onto the sprocket 7. Place chain over and behind clutch, fit- ting the drive links in the clutch drum sprocket. -
Page 8: Operation
Adjusting Screw - - 1/4 Turn S Lift up the tip of the bar and tighten the chain brake nuts with the bar tool. S Recheck chain tension. OPERATION KNOW YOUR CHAIN SAW READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR CHAIN SAW. -
Page 9: Starting A Cold Engine
Poulan oil resists high temperature thinning. If Poulan bar and chain oil is not available, use a good grade SAE 30 oil. S Never use waste oil for bar and chain lubri- cation. -
Page 10: Starting A Warm Engine
choke/fast idle lever is pulled out to the full extent, the correct throttle setting for starting is set automatically. ON/STOP SWITCH (SIDE VIEW) STOP 1. Move ON/STOP switch to the ON posi- tion. 2. Slowly press primer bulb 6 times. 3. -
Page 11: Cutting Methods
CUTTING METHODS IMPORTANT POINTS S Check chain tension before first use and after 1 minute of operation. See CHAIN TENSION in the ASSEMBLY section. S Cut wood only. Do not cut metal, plastics, masonry, non-wood building materials, etc. S Stop the saw if the chain strikes a foreign object. - Page 12 control fall Opening of felling Closing of notch NOTE: Before felling cut is complete, use wedges to open the cut if necessary to control the direction of fall. To avoid kickback and chain damage, use wood or plastic wedges, but never steel or iron wedges. S Be alert to signs that the tree is ready to fall: cracking sounds, widening of the fell- ing cut, or movement in the upper...
- Page 13 If any dealer other than an authorized service dealer performs work on the product, Poulan may not pay for repairs under warranty. It is your responsibility to maintain and perform general mainte- nance.
-
Page 14: Cleaning The Spark Arrest- Ing Screen
MAINTENANCE SCHEDULE Check: Fuel mixture level ..Before each use Bar lubrication ..Before each use Chain tension ..Before each use Chain sharpness ..Before each use For damaged parts . -
Page 15: Bar Maintenance
about performing this procedure, contact your authorized service dealer 1- -800- -554- -6723. BAR MAINTENANCE If your saw cuts to one side, has to be forced through the cut, or been run with an improper amount of bar lubrication it may be neces- sary to service your bar. -
Page 16: Troubleshooting Table
SEQUENTIAL DAMAGES, ABOVE LIMITATIONS OR EXCLUSION MAY NOT APPLY TO YOU. The policy of Poulan is to continuously im- prove its products. Therefore, Poulan re- serves the right to change, modify, or discon- tinue models, designs, specifications, and accessories of all products at any time with-... -
Page 17: Warranty
You are responsible for presenting your small off- -road engine to an Poulan/ WEED EATER authorized repair center as soon as a problem exists. Warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days. - Page 18 The information on the product label indicates which standard your engine is certified. Example: (Year) EPA Phase 1 or Phase 2 and/or CALIFORNIA. This engine is certified to be emissions compliant for the following use: Moderate (50 hours) Intermediate (125 hours) Extended (300 hours)
Need help?
Do you have a question about the 545123582 and is the answer not in the manual?
Questions and answers