Felker FTS-150 Operating Instructions And Parts List Manual
  1. Manuals
  2. Brands
  3. Felker Manuals
  4. Saw
  5. FTS-150
  6. Operating instructions and parts list manual

Felker FTS-150 Operating Instructions And Parts List Manual

Felker operating instruction tile saw fts-150
Hide thumbs
Table of Contents

Advertisement

Quick Links

OPERATING INSTRUCTIONS AND PARTS LIST
INSTRUCTIONS D'UTILISATION ET LISTE DE PIÈCES
INSTRUCCIONES DE OPERACIÓN Y LISTA DE PIEZAS
FTS-150 TILE SAW
MODEL: FTS-150 115V/60/1
0AF04106
Copyright © December, 2003
Electrolux Construction Products
17400 West 119th Street
Olathe, Kansas 66061
Customer Service ......800-365-4003
Corp. Office ...............913-928-1000
Cust. Service FAX......800-825-0028
Corp. Office FAX .......913-438-7951
Internet ......www.felkersaws.com

Advertisement

Table of Contents
loading

Related Manuals for Felker FTS-150

Summary of Contents for Felker FTS-150

  • Page 1 OPERATING INSTRUCTIONS AND PARTS LIST INSTRUCTIONS D’UTILISATION ET LISTE DE PIÈCES INSTRUCCIONES DE OPERACIÓN Y LISTA DE PIEZAS FTS-150 TILE SAW MODEL: FTS-150 115V/60/1 0AF04106 Copyright © December, 2003 Electrolux Construction Products 17400 West 119th Street Olathe, Kansas 66061 Customer Service ...800-365-4003 Corp.

  • Page 2: Table Of Contents

    EVERY MACHINE IS THOROUGHLY TESTED BEFORE LEAVING THE FACTORY. SUPPLIED WITH A COPY OF THIS MANUAL. FAMILIAR WITH THE SAFETY WARNINGS. FAILURE TO OBEY WARNINGS MAY RESULT IN INJURY OR DEATH. FOLLOW INSTRUCTIONS STRICTLY TO ENSURE LONG SERVICE IN NORMAL OPERATION. CONTENTS Symbol Definitions ...4 - 5 Decal Descriptions and Locations...6...
  • Page 3 ANTES DE SALIR DE NUESTRA FÁBRICA, CADA MÁQUINA ES SOMETIDA A PUREBAS DETENIDAS. CADA MÁQUINA DE CORTE ES ENTREGADA CON UNA CIPIA DE ESTE MANUAL. LOS OPERARIOS DE ESTOS EQUIPOS DEBEN LEER Y FAMILIARIZARSE CON LAS INSTRUCCIONES DE SEGURIDAD. EL NO PRESTAR ATENCIÓN A ESTAS ADVERTENCIAS PUEDE OCASIONAR GRAVES LESIONE.

  • Page 4: Symbol Definitions

    Symbols Definitions Symboles Definición De Simbolos • Please read the instructions for use prior to operating the machine for the first time. • Avant toute mise en service, lire attentivement la notice et se familiariser avec la machine. • Antes de la puesta en marcha, lea detenidamente las instrucciones y familiaricese con la máquina. •...
  • Page 5 • Wear Appropriate Clothing • Port obligatoire de la tenue appropriée • Usar Ropa Adecuada • Machinery Hazard, Keep Hands And Feet Clear • Danger! Rester à distance de la machine • Máquina Peligrosa - Mantenga Manos Y Pies Alejados De La Máquina •...

  • Page 6: Decal Descriptions And Locations

    DECAL DESCRIPTIONS & LOCATION AUTOCOLLANTS – DESCRIPTIONS ET EMPLACEMENTS DESCRIPTIÓN DE CALCAMONIAS Y UBICACIONES P/N 046326 LOCATION: Motor – Front P/N 189247 LOCATION: Control Box – WP Outlet P/N 193015 LOCATION: Blade Guard – Top Sides P/N 193014 LOCATION: Water Tray – Front LOCATION: Cutting Head –...
  • Page 7 NOTES:...

  • Page 8: Safety Warnings - Do's & Do Not's

    WARNING: FAILURE TO COMPLY WITH THESE WARNINGS AND OPERATING INSTRUCTIONS COULD RESULT IN DEATH OR SERIOUS BODILY INJURY. read this entire operator’s manual before operating this machine. Understand all warnings, instructions, and controls. keep all guards in place and in good condition. wear safety approved hearing, eye, head and respiratory protection.
  • Page 9 This saw was designed for certain applications only. DO NOT modify this saw or use for any application other than for which it was designed. If you have any questions relative to its application, DO NOT use the saw until you have written Electrolux Construction Products and we have advised you.

  • Page 10: Instructions

    INDICATION INFORMATION INSTRUCTION PROHIBITION Your FELKER tile saw is a ruggedly constructed unit engineered to give long, satisfactory performance. Simple, daily maintenance and care will add to the life and productivity of your tile saw. • Full 1-1/2 HP, 115V/60/1 motor for powerful cuts.
  • Page 11 M10 Flatwashers (8) and Locknuts (9). • After the Saw Stand is completely assembled as shown and all fasteners are securely tightened, the tile saw can be installed on Stand using the two Saw Stand Knobs (10, Fig 1B). Fig 1A WATER TRAY INSTALLATION...
  • Page 12 CUTTING HEAD INSTALLATION (FIG 3) • Remove Cutting Head Assembly (1) and Frame and Pan Assembly (2) from carton. • Using the multi-wrench provided, install the Motor Support Shaft (3) into the Rear Support Post (4). Install and tighten the Capscrew (5) with washer to retain the Support Shaft (3).
  • Page 13 Check that the main voltage is identical to that of the machine. POSITION OF TILE SAW • Position the saw to one side of a wall-mounted receptacle to prevent water from collecting onto the receptacle or plug. The user should also create a “drip loop”...

  • Page 14: Operating Procedures

    Keep cord away from heat and sharp edges. Always disconnect the extension cord from disconnecting the saw from the extension cord. Minimum wire gage for cord Ampere Rating Total length of cord in feet 25ft. 50 ft.

  • Page 15: Alignment Procedures

    NOTE: THERE ARE NO ADJUSTMENTS TO WATER TRAY Alignment Procedures Your FTS-150 tile saw is factory assembled and aligned prior to shipment to ensure accurate cuts when your saw is delivered. However, since FELKER can not control rough handling during shipping, it is suggested that the alignment be checked.

  • Page 16: Trouble Shooting Guide

    Check to see if the water pump is clean and free of any chips, debris, clogging, etc. SAW WON’T CUT STRAIGHT • Check to see if saw frame or rolling guide bar is bent. • Check to see if the support for the cutting table is bent.

  • Page 17: Accessory Use & Installation

    See Stand Assembly Instruction. The stand comes with two wheels at the rear. Each wheel has its own sturdy brake. The stand is designed with locating pins at each end to locate the saw frame and securely fastens to the underside of the frame with two knobs.

  • Page 18: Mises En Garde De Sécurité - Faire, Ne Pas Faire

    ATTENTION: LE MON RESPECT DE CES MISES EN GARDE ET INSTRUCTIONS D’UTILISATION PEUT ENTRAÎNER LA MORT OU DES BLESSURES CORPORELLES GRAVES Faire Lire ce manuel d’utilisation entièrement avant d’utiliser cette machine. Comprendre toutes les mises en garde, les instructions et les commandes. Faire Toujours maintenir les protections en place et en bonne condition.
  • Page 19 ATTENTION : LE MON RESPECT DE CES MISES EN GARDE ET INSTRUCTIONS D’UTILISATION PEUT ENTRAÎNER LA MORT OU DES BLESSURES CORPORELLES GRAVES utiliser cette machine avant d’avoir lu et compris ce manuel de fonctionnement. NE PAS utiliser cette machine sans protection de disque ou sans qu’une autre protection soit montée. NE PAS se tenir derrière ou devant le chemin du disque lorsque le moteur est en marche.
  • Page 20 ADVERTENCIA: EL NO RESPETAR ESTAS ADVERTENCIAS E INSTRUCCIONES DE OPERACION PUEDE PROVOCAR GRAVES LESIONES O LA MUERTE. lea todo el manual antes de manejar esta máquina. Entienda todas las advertencias, instrucciones y controles. mantenga siempre las protecciones en su lugar y en buenas condiciones. siempre use protecciones aprobadas para los oídos, ojos, cabeza y respiración.
  • Page 21 ADVERTENCIA: EL NO RESPETAR ESTAS ADVERTENCIAS E INSTRUCCIONES DE OPERACION PUEDE PROVOCAR GRAVES LESIONES O LA MUERTE. haga funcionar esta máquina sin antes haber leído y entendido este manual. maneje esta máquina sin tener la protección de la hoja u otras protecciones instaladas en su lugar. se sitúe detrás del paso de la hoja mientras el motor está...

  • Page 22: Diagrams And Spare Parts

    DIAGRAM 1...
  • Page 23 DIAGRAM 1 – FTS-150 PARTS LIST DIAG. PART LOC. DESCRIPTION 185004 Stand Assy (Incls. 1, 2, & 3) 185017 Wheel w/ Brake & fasteners 185018 Knobs, M8x16 185019 Fame Assy (incls. 4 & 6) 185020 Bar, Roller Guide w/ fasteners & clamps...
  • Page 24 WIRING DIAGRAM: NOTES:...

  • Page 25: Warranty

    MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Please record the Date of Purchase and the Serial Number of your saw in the space below. (The serial number is located on the side of the motor.) When ordering service items, please have this information available.
  • Page 26 Felker Corporate Office 17400 West 119th Street Olathe, Kansas 66061 Phone: 913-928-1000 Customer Service Tel: 800-365-4003 Customer Service Fax: 800-825-0028 Corporate Office Fax: 913-438-7951 Customer Service Int'l: 913-928-1258 Western Division Center 2012 Abalone Avenue Torrance, CA 90501 310-381-3100 Felker Latin America, Mexico, Caribbean, Central and South America 17400 West 119th Street Olathe, Kansas 66061...

This manual is also suitable for:

Fts-15

Table of Contents