Porter-Cable 7310 Instruction Manual

Double insulated laminate trimmers

Hide thumbs Also See for 7310:

Instruction manual (25 pages)

Instruction manual (64 pages)

Instruction manual (22 pages)

Table Of Contents

Table of Contents

Quick Links

Summary of Contents for Porter-Cable 7310

Page 1 Note: Rockler may not carry all products and/or sizes listed in this vendor's publication Instruction manual 73999 MODEL 7310 Trimmer MODEL 7320 Base To learn more about Porter-Cable visit our website at: http://www.porter-cable.com Copyright © 2005 Porter-Cable ESPAÑOL: PÁGINA 23 FRANÇAISE : PAGE 43 Double Insulated Laminate Trimmers...
Page 2: Table Of Contents
Improper operation, maintenance or modification of tools or equipment could result in serious injury and property damage. There are certain applications for which tools and equipment are designed. Porter-Cable strongly recommends that this product NOT be modified and/or used for any application other than for which it was designed.
Page 3: Safety Guidelines
SAFETY GUIDELINES - DEFINITIONS It is important for you to read and understand this manual. The information it contains relates to protecting YOUR SAFETY and PREVENTING PROBLEMS. The symbols below are used to help you recognize this information. indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
Page 4: General Safety Rules
GENERAL SAFETY RULES Read all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. The term "power tool" in all of the warnings listed below refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.
Page 5 GENERAL SAFETY RULES on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. Dress properly.
Page 6: Additional Specific Safety Rules
12. NEVER TOUCH router bits after use. They may be extremely hot. 13. NEVER TIGHTEN COLLET NUT without a bit. 14. DO NOT USE LAMINATE TRIMMER MOTOR WITHOUT THE LAMINATE TRIMMER BASE INSTALLED. Loss of control could result, causing personal injury or damage to work.
Page 7 IPXX ... IP symbol MOTOR Many Porter-Cable tools will operate on either D.C., or single phase 25 to 60 cycle A.C. current and voltage within plus or minus 5 percent of that shown on the specification plate on the tool. Several models, however, are designed for A.C.
Page 8: Functional Description
18-20 FUNCTIONAL DESCRIPTION FOREWORD Porter-Cable Laminate Trimmers are designed for the flush and bevel trimming of laminated plastics, phenolics, and other similar materials that have a bonding agent too hard to be trimmed with ordinary tools. The Tilt-Base model allows trimming into corners inaccessible to standard trimmers.
Page 9: Carton Contents
1. Trimmer motor 2. Trimmer base (or bases, if a kit is purchased) 3. Wrench (or wrenches, if a kit is purchased) NOTE: This tool is shipped completely assembled. No assembly time or tools are required. MODEL 7301 MOTOR UNIT All laminate trimmers in this manual use the Model 7301 Motor Unit.
Page 10 TO INSTALL THE BIT DISCONNECT THE TOOL FROM THE POWER SOURCE. On Models 7310 and 7319, you can install bits either with the motor unit attached or removed. NOTE: See the instructions (Model 7312) for installing the bit in the OFFSET trimmer.
Page 11 The optional Model 73100 Edge Guide Kit is available for use with the Model 7310 trimmer. This kit is designed for use with non-piloted bits on curved or straight applications. Non-piloted bits can produce a 90° straight cut, a 10°...
Page 12 ATTACHING AND ADJUSTING THE BASE AND THE ROLLER GUIDE Remove the power unit from the base unit (see “TO INSTALL BIT”). Install the bit. The base and roller guide (A) Fig. 5 is assembled at the factory. To install, remove a sub-base mounting screw (A) Fig. 6 and insert the alignment pin (in the guide base) into the hole (C) in the bottom of the trimmer sub-base.
Page 13 USING STRAIGHT EDGE GUIDE You can use the straight edge guide (D) Fig. 5 with either bit for trimming straight edges. Attach it to the guide base and adjust similar to the other guides. MODEL 7319 TILT BASE TRIMMER ASSEMBLY Model 7319 Tilt Base Trimmer is completely attached at the factory.
Page 14 MODEL 7312 OFFSET TRIMMER ASSEMBLY Your Model 7312 Offset Trimmer was assembled at the factory. However, if you choose to attach an auxiliary base, use the following instructions: DISCONNECT THE TOOL FROM THE POWER SOURCE! Remove the collet nut and collet from the motor unit. Attach the drive pulley (A) Fig.
Page 15 TO INSTALL & REMOVE THE BIT DISCONNECT THE TOOL FROM THE POWER SOURCE! Insert the long portion of the hex wrench (A) Fig. 13 through the spindle lock hole (B) Fig. 13, so that the wrench protrudes from both sides of the base housing. Rotate the spindle by hand to align the hole in the spindle with the holes in the housing.
Page 16: Troubleshooting
DISCONNECT THE TOOL FROM THE POWER SOURCE. Always wear safety glasses while operating a laminate trimmer. Allow your workpiece to overhang the base material by at least 1/8". Firmly grasp the motor housing, being sure switch is in the “OFF” position.
Page 17 OPERATION – Trimming " backsplash with the new Porter-Cable Offset Laminate Trimmer fitted with a solid carbide self- piloted bit. Fig. 18 IN-AND-OUT TRIMMING OF INSTALLED CORNER APPLICATION – Trimming into and...
Page 18 Trims up to vertical surfaces. ADJUSTING THE BIT EXPOSURE DISCONNECT THE TOOL FROM THE POWER SOURCE. Loosen the base locking screw (E) Fig. 20 approximately 1/4 turn. Turn the depth-adjusting wheel (D) Fig. 20 counter-clockwise (looking at top of wheel) to lower the bit until it touches the guide plate.
Page 19 The “butt” joint is commonly used in the construction of face frames. To install a laminate covering on a face frame: Always wear safety glasses while operating a laminate trimmer. Trimmer Base Sub-Base Installed laminate Guide Lip Laminate Cut the pieces of laminate covering to rough size. Apply contact cement to the face frame and the laminate pieces in the normal manner.
Page 20: Maintenance
11. Repeat this process as necessary to complete the face frame. For assistance with your tool, visit our website at www.porter-cable.com for a list of service centers, or call the Porter-Cable Customer Care Center at 1-800- 223-7278. KEEP TOOL CLEAN Periodically blow out all air passages with dry compressed air.
Page 21: Service
We cannot guarantee repairs made or attempted by others. You can also write to us for information at PORTER-CABLE, 4825 Highway 45 North, Jackson, Tennessee 38305 - Attention: Product Service. Be sure to include all of the information shown on the nameplate of your tool (model number, type, serial number, etc.).
Page 22: Warranty
PORTER-CABLE LIMITED ONE YEAR WARRANTY Porter-Cable warrants its Professional Power Tools for a period of one year from the date of original purchase. We will repair or replace at our option, any part or parts of the product and accessories covered under this warranty which, after examination, proves to be defective in workmanship or material during the warranty period.
Page 23: Español
® 4825 Highway 45 North Jackson, TN 38305 1-800-223-7278 www.porter-cable.com...

This manual is also suitable for:

7312 7319 7320

Porter-Cable 7310 Instruction Manual

Quick Links

Related Manuals for Porter-Cable 7310

Summary of Contents for Porter-Cable 7310

This manual is also suitable for:

Table of Contents