Dimensions; Installation; Specifications - Mitsubishi Electric FX3S Quick Start Manual

[5] Service power supply terminals (only AC power type) Wire
sensors or other external equipment to these terminals when the
service power supply (24 VDC) is used for such equipment.

2. DIMENSIONS

2-Ø 4.5 mounting holes
W1 (Mounting hole pitches)
W
Mounting hole pitches
Model Number W: mm (inches)
FX3S-10MR/ES 60 (2.37")
FX3S-14MR/ES 60 (2.37")
FX3S-20MR/ES 75 (2.96")
FX3S-30MR/ES 100 (3.94")
INSTALLATION: 35-mm-wide DIN rail or Direct (screw) mounting
(M4×2)

3. INSTALLATION

CAUTION: INSTALLATION PRECAUTIONS
• Use the product within the generic environment specifications
described in this manual. Never use the product in areas with
excessive dust, oily smoke, conductive dusts, corrosive gas (salt
air, Cl2, H2S, SO2 or NO2), flammable gas, vibration or impacts, or
expose it to high temperature, condensation, or rain and wind. If the
product is used in such conditions, electric shock, fire, malfunctions,
deterioration or damage may occur.
• Do not touch the conductive parts of the product directly. Doing so
may cause device failure or malfunctions.
• Install the product securely using a DIN rail or mounting screws.
• Install the product on a flat surface. If the mounting surface is
rough, undue force will be applied to the PC board, thereby causing
nonconformities.
• When drilling screw holes or wiring, make sure cutting or wire debris
do not enter the ventilation slits. Failure to do so may cause fire,
equipment failures or malfunctions.
• Be sure to remove the dust proof sheet from the PLC's ventilation
port when installation work is completed. Failure to do so may cause
fire, equipment failures or malfunctions.
• Connect the peripheral device cables securely to their designated
connectors.
• Loose connections may cause malfunctions.
Mitsubishi Electric Automation, Inc.
Unit: mm (inches)
8 (0.32")
75 (2.96"): AC power type
49 (1.93"): DC power type
W1: mm (inches)
Weight: kg (lbs)
Direct mounting
Approx
hole pitches
52 (2.05") 0.30 (0.66 lbs)
52 (2.05") 0.30 (0.66 lbs)
67 (2.64") 0.40 (0.88 lbs)
92 (3.63") 0.45 (0.99 lbs)
NOTES
• When a dust proof sheet is supplied with units, keep the sheet
applied to the ventilation slits during installation and wiring work.
• To prevent temperature rise, do not install the PLC on a floor, a
ceiling or a vertical surface. Install it horizontally on a wall as shown
in this manual.
• Keep a space of 50 mm (1.97") or more between the unit main body
and another device or structure (part A). Install the unit as far away
as possible from high-voltage lines, high-voltage devices and power
equipment.
DANGER: WIRING PRECAUTIONS
• Make sure to cut off all phases of the power supply externally before
attempting installation or wiring work. Failure to do so may cause
electric shock or damage to the product.

3.1 SPECIFICATIONS

n COMPLIANCE WITH EC DIRECTIVE (CE MARKING )
This document does not guarantee that a mechanical system including
this product will comply with the following standards. Compliance
to EMC directive and LVD directive of the entire mechanical system
should be checked by the user/manufacturer. For more details please
contact Mitsubishi Electric at Amzsupport@meau.com
n REQUIREMENT FOR COMPLIANCE WITH EMC DIRECTIVE
The following products have shown compliance through direct testing
(of the identified standards below) and design analysis (through the
creation of a technical construction file) to the European Directive for
Electromagnetic Compatibility (2004/108/EC) when used as directed
by the appropriate documentation.
ATTENTION
• This product is designed for use in industrial applications.
• Manufactured by:
Mitsubishi Electric Corporation
2-7-3 Marunouchi, Chiyoda-ku, Tokyo, 100-8310 Japan
• Manufactured at:
Mitsubishi Electric Corporation Himeji Works
840 Chiyoda-machi, Himeji, Hyogo, 670-8677 Japan
• Authorized Representative in the European Community:
Mitsubishi Electric Europe B.V.
Gothaer Str. 8, 40880 Ratingen, Germany
Type: Programmable Controller (Open Type Equipment)
Models: MELSEC FX3S series, FX3G series, FX3U series
manufactured
From November 1st, 2008
FX3G-232-BD
FX3U-485-BD
FX3G-422-BD
From March 1st, 2013
FX3S-_ _MR/ES
Where _ _ indicates 10,14, 20, 30
From September 1st, 2013
FX3G-485-BD-RJ
FX3S QUICK START MANUAL
5