1. Manuals
  2. Brands
  3. Polaris Manuals
  4. Offroad Vehicle
  5. Outlaw 9922079
  6. Owner's manual

Polaris Outlaw 9922079 Owner's Manual

Polaris industries 2009 all-terrain vehicle owner's manual
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual

Advertisement

Table of Contents
loading

Related Manuals for Polaris Outlaw 9922079

Summary of Contents for Polaris Outlaw 9922079

  • Page 3 WARNING The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. A card containing important ATV safety information should be attached to the owner's manual on the next page. If you cannot locate this card, or if it has been removed, please call 1-800-342-3764 for assistance.
  • Page 4 Visit us at www.polarisindustries.com...
  • Page 5 POLARIS and POLARIS THE WAY OUT are registered trademarks of Polaris Industries Inc. Copyright 2008 Polaris Sales Inc. All information contained within this publication is based on the latest product information at the time of publication. Due to constant improvements in the design and quality of production components, some minor discrepancies may result between the actual vehicle and the information presented in this publication.
  • Page 6 Welcome Thank you for purchasing a Polaris vehicle, and welcome to our world-wide family of Polaris owners. We proudly produce an exciting line of utility and recreational products. • Snowmobiles • All-terrain vehicles (ATVs) • RANGER utility vehicles • Victory motorcycles...
  • Page 7 We also take great pride in our Pure Polaris products, available through our online store at www.purepolaris.com. Have your accessories and clothing delivered right to your door!

  • Page 8: Table Of Contents

    Specifications ....168 Polaris Products ... . 170 Troubleshooting... . . 172 Warranty .

  • Page 9: Introduction

    Introduction Safety Words and Symbols The following signal words and symbols appear throughout this manual and on your vehicle. Your safety is involved when these words and symbols are used. Become familiar with their meanings before reading the manual. The safety alert symbol indicates a potential personal injury hazard.
  • Page 10 Failure to follow the warnings and safety precautions contained in this manual can result in severe injury or death. A Polaris ATV is not a toy and can be hazardous to operate. This vehicle handles differently than other vehicles, such as motorcycles and cars. A collision or rollover can occur quickly, even during routine maneuvers like turning, or driving on hills or over obstacles, if you fail to take proper precautions.

  • Page 11: Vehicle Identification Numbers

    Remove the spare key and store it in a safe place. An ignition key can be duplicated only by ordering a Polaris key blank (using your key number) and mating it with one of your existing keys. The ignition switch must be replaced if all keys are lost.
  • Page 12 Introduction Vehicle Identification Numbers Vehicle Model Number: ____________________________________________________________________ Frame Vehicle Identification Number (1): ______________________________________________________ Engine Serial Number (2):__________________________________________________________________ Key Number (on the key): __________________________________________________________________...

  • Page 13: Safety

    You should review this information on a regular basis. available to If you purchased a used Polaris ATV, you can take the ATV RiderCourse ATV Enrollment Express at (800) 887-2887 or by visiting www.atvsafety.org.
  • Page 14 Safety Training A Polaris ATV is an off-road vehicle. Familiarize yourself with all laws and regulations concerning the operation of this vehicle in your area. FOR MORE INFORMATION ABOUT ATV SAFETY, call the Consumer Product Safety Commission at 1-800-638-2772, or visit www.cpsc.gov, visit www.atvsafety.org, or call Polaris at 1-800-342-3764.

  • Page 15: Equipment Modifications

    The warranty on your Polaris ATV is terminated if any equipment has been added to the vehicle, or if any modifications have been made to the vehicle, that increase its speed or power.

  • Page 16: Safe Riding Gear

    Helmet Wearing a helmet can prevent a severe head injury. When- ever riding a Polaris vehicle, always wear a helmet that meets or exceeds established safety standards. Approved helmets in the USA and Canada bear a U.S.

  • Page 17: Eye Protection

    Safe Riding Gear Eye Protection Do not depend on eyeglasses or sunglasses for eye protection. Whenever riding a Polaris vehicle, always wear shatterproof goggles or use a shatterproof helmet face shield. Polaris recommends wearing approved Personal Protective Equipment (PPE) bearing markings such as VESC 8, V-8, Z87.1, or CE.

  • Page 18: Safety Warnings

    Safety Safety Warnings WARNING Failure to operate the ATV properly can result in a collision, loss of control, accident or overturn, which may result in serious injury or death. Heed all safety warnings outlined in this section of the owner’s manual.

  • Page 19: Operating Without Instruction

    Beginning and inexperienced operators should complete the ATV RiderCourse offered by Polaris through the SVIA. They should then regularly practice the skills learned in the course and the operating techniques described in the Owner's Manual.

  • Page 20: Handling Gasoline

    Safety Warnings Handling Gasoline Gasoline is highly flammable and explosive under certain conditions. • Always exercise extreme caution whenever handling gasoline. • Always refuel with the engine stopped, and outdoors or in a well ventilated area. • Do not smoke or allow open flames or sparks in or near the area where refueling is per- formed or where gasoline is stored.

  • Page 21: Protective Apparel

    Safety Safety Warnings Failure to Inspect Before Operating Failure to inspect and verify that the ATV is in safe operating condition before operating increases the risk of an accident. Always inspect the ATV before each use to make sure it's in safe operating condition.

  • Page 22: Carrying A Passenger

    Safety Warnings Carrying a Passenger Carrying a passenger greatly reduces the operator's ability to balance and control the ATV, which may result in an accident or overturn. Never carry a passenger on this ATV. Using Alcohol or Drugs Operating the ATV after consuming alcohol or drugs could adversely affect operator judgment, reaction time, balance and perception.

  • Page 23: Operating On Pavement

    Safety Warnings Operating on Pavement Operating an ATV on paved surfaces (including sidewalks, paths, parking lots and driveways) may adversely affect the handling of the ATV and could result in loss of control and accident or overturn. Avoid operating the ATV on pavement. ATV tires are designed for off-road use.

  • Page 24: Physical Control Of The Atv

    Safety Warnings Operating at Excessive Speeds Operating the ATV at excessive speeds increases the operator's risk of losing control. Always operate at a speed that's appropriate for the terrain, the visibility and operating conditions, and your experience. Physical Control of the ATV Removing a hand from the handlebars or feet from the footpegs during operation can reduce your ability to control the vehicle or cause loss of...

  • Page 25: Turning Improperly

    Safety Warnings Turning Improperly Turning improperly could cause loss of traction, loss of control, accident or overturn. Always follow proper procedures for turning as described in the owner's manual. Never turn abruptly or at sharp angles. Never turn at high speeds. Practice turning at slow speeds before attempting to turn at faster speeds.

  • Page 26: Improper Hill Climbing

    Safety Warnings Improper Hill Climbing Improper hill climbing could cause loss of control or overturn. Always follow proper procedures for climbing hills as described in the owner's manual. See page 72. Operating on Steep Hills Operating on excessively steep hills could cause an overturn.

  • Page 27: Descending Hills Improperly

    Safety Warnings Descending Hills Improperly Improperly descending a hill could cause loss of control or overturn. • Always follow proper procedures for traveling down hills as described in the owner's manual. NOTE: A special tech- nique is required when braking while traveling downhill. See page 75.

  • Page 28: Crossing Hillsides

    Safety Safety Warnings Crossing Hillsides Driving on a sidehill is not recommended. Improper procedure could cause loss of control or overturn. Avoid crossing the side of any hill unless absolutely necessary. If crossing a hillside is unavoidable, always follow proper procedures as described in the owner's manual.

  • Page 29: Stalling While Climbing A Hill

    Safety Safety Warnings Stalling While Climbing a Hill Stalling, rolling backwards or improperly dismounting while climbing a hill could cause an overturn. Always maintain a steady speed when climbing a hill. If all forward speed is lost Keep body weight uphill. Apply the front brakes gradually (right lever).

  • Page 30: Operating On Slippery Terrain

    Safety Safety Warnings Operating on Slippery Terrain Failure to use extra caution when operating on excessively rough, slippery or loose terrain could cause loss of traction, loss of control, accident or overturn. Do not operate on excessively rough, slippery or loose terrain until you've learned and practiced the skills necessary to control the ATV on such terrain.

  • Page 31: Improper Tire Maintenance

    Safety Safety Warnings Operating in Unfamiliar Terrain Failure to use extra caution when operating on unfamiliar terrain could result in an accident or overturn. Unfamiliar terrain may contain hidden rocks, bumps, or holes that could cause loss of control or overturn. Travel slowly and use extra caution when operating on unfamiliar terrain.

  • Page 32: Skidding Or Sliding

    Never modify the ATV through improper installation or use of accessories. All parts and accessories added to the vehicle must be genuine Polaris Industries Inc. or equivalent components designed for use on this ATV and should be installed and used according to approved instructions.

  • Page 33: Operating Through Deep Water

    Safety Safety Warnings Operating Through Deep Water Operating the ATV through deep or fast-flowing water could cause the tires to float, causing loss of control or overturn. Avoid operating through deep or fast-flowing water. If it's unavoidable to enter water that exceeds the height of the footpegs: •...

  • Page 34: Poor Visibility

    Safety Safety Warnings Poor Visibility Operating the ATV in darkness or inclement weather could result in a collision or accident, especially if operating on a road or street. This ATV is not equipped with highway-approved lights. Operate this vehicle off-road only. Use caution and drive at reduced speeds in conditions of reduced visibility such as fog, rain and darkness.

  • Page 35: Physical Skills

    Safety Safety Warnings Operating on Frozen Bodies of Water Operating on frozen bodies of water may result in serious injury or death if the ATV and/or the operator fall through the ice. Never operate the ATV on a frozen body of water. Operating a Damaged ATV Operating a damaged ATV can result in an accident.

  • Page 36: Hot Exhaust Systems

    Safety Warnings Hot Exhaust Systems Exhaust system components are very hot during and after use of the vehicle. Hot components can cause burns and fire. Do not touch hot exhaust system components. Always keep combustible materials away from the exhaust system. Use caution when traveling through tall grass, especially dry grass.
  • Page 37 If an informational or graphic label becomes illegible or comes off, contact your Polaris dealer to purchase a replacement. Replacement safety labels are provided Age 16 by Polaris at no charge. The part num- Warning ber is printed on the label.

  • Page 38: General Warning

    Safety Labels and Locations General Warning WARNING Improper ATV use can result in SEVERE INJURY OR DEATH. Always use an approved helmet and protective gear. Never use on public roads. Never carry passengers. Never use with drugs or alcohol. NEVER operate: •...

  • Page 39: Age 16 Warning

    Safety Safety Labels and Locations Age 16 Warning WARNING Operating this ATV if you are under the age of 16 increases your chance of severe injury or death. NEVER operate this ATV if you are under age Discretionary/Sport ATV Warning WARNING •...

  • Page 40: Tire Pressure/Load Warning

    Safety Labels and Locations No Passenger Warning WARNING NEVER ride as a passenger. Passengers can cause a loss of control, resulting in SEVERE INJURY or DEATH. No Passenger Warning Tire Pressure/Load Warning WARNING Improper tire pressure or overloading can cause loss of control.

  • Page 41: Features And Controls

    Features and Controls Engine Main Key Switch Stop Switch Start Button...

  • Page 42: Start Button

    Start Button Press the start button to engage the starter. Always release the start button promptly when the engine starts. If the starter fails to engage, replace the blown fuse or see your Polaris dealer. Engine Stop Switch Move the stop switch either left or right to the OFF position to stop the engine quickly.

  • Page 43: Indicator Lights

    • Hot engine • Reverse gear is selected • Neutral gear is selected If indicator lights fail to operate, check connections. See your Polaris dealer for inspection of the capacitor and voltage regulator.
  • Page 44 Features and Controls Lights Headlights Use the headlight switch to turn the lights on and off and to switch the lights from high beam to low beam. The key must be in the ON position and the engine stop switch must be in the RUN position to operate the headlights.

  • Page 45: Clutch Lever

    Features and Controls Clutch Lever The hydraulic clutch lever is located on the left handlebar. Squeeze the clutch lever toward the handlebar to disengage the clutch. Disengage the clutch before shifting gears. Adjusting Knob The clutch is self-adjusting, but lever position can be changed to fit the operator’s hand.

  • Page 46: Clutch Fluid

    Clutch Oil. Do not use brake fluid. Do not mix clutch fluid with any other hydraulic fluids. See page 170 for the part numbers of Polaris products. 1. Position the vehicle on a level surface. 2. Turn the handlebar until the master cylinder is in a horizontal position.

  • Page 47: Throttle Lever

    Features and Controls Throttle Lever WARNING Operating an ATV with sticking or improperly operating throttle controls could cause an accident. Never start or operate an ATV that has a sticking or improperly operating throttle. Always contact your dealer for service before operating the vehicle. Failure to check or maintain proper operation of the throttle system can result in an accident if the throttle lever sticks during operation.
  • Page 48 Features and Controls Throttle Lever The throttle lever is located on the right handlebar. Squeeze the lever toward the handlebar to increase engine speed and vehicle movement. Fuel is injected into the intake passage each time throttle is applied. Do not squeeze the throt- tle lever while starting the engine.

  • Page 49: Foot Brake

    Features and Controls Foot Brake The foot brake operates the rear brakes. The brake pedal is located in front of the right-hand footpeg. If the rear wheels slide while using the foot brake, reduce brake pedal pressure to brake the wheels without skidding. Check the brake fluid level frequently for the Foot Brake foot brake system.

  • Page 50: Hand Brake

    Features and Controls Hand Brake The hand brake operates the front brakes. The hand Hand Brake (Front Brake) brake is located on the right handlebar. These brakes are hydraulically activated disc type brakes. Squeeze the brake lever toward the handlebar to engage the front brakes.
  • Page 51 Features and Controls Master Cylinder/Brake Fluid WARNING An over-full master cylinder may cause brake drag or brake lock-up, which could result in an accident. Maintain brake fluid at the recommended level. Do not overfill. Never store or use a partial bottle of brake fluid. Brake fluid is hygroscopic, meaning it rapidly absorbs moisture from the air.
  • Page 52 Master Cylinder/Brake Fluid Check the brake fluid in the master cylinder before each ride. If the fluid level is low add DOT 4 brake fluid only. Do not overfill. See page 170 for the part numbers of Polaris prod- ucts.

  • Page 53: Parking Brake

    Features and Controls Parking Brake 1. Place the transmission in first gear. 2. Squeeze and release the brake lever two or three times, then squeeze and hold. 3. Push the parking brake lock inward to engage the lock. Release the brake lever. 4.
  • Page 54 Features and Controls Parking Brake The parking brake may relax if left on for a long period of time. Always block the wheels to prevent rolling. Always block the wheels on the downhill side of the ATV if leaving it parked on a hill.

  • Page 55: Shift Pedal

    Features and Controls Manual Shift Shift Pedal The gear shift pedal is located in front of the left-hand footpeg. One full stroke of the pedal shifts the transmission to the next gear in the shifting sequence. The pedal automatically returns to a horizontal position when released.

  • Page 56: Shifting Gears

    Manual Shift Shifting Gears Always allow a cold engine to warm up before shifting gears. 1. When starting from a stopped position, place the transmission in neutral. 2. Squeeze and hold the brake lever. Do not apply throttle. 3. Squeeze the clutch lever to disengage the clutch.

  • Page 57: Reverse Lock-Out Switch

    Features and Controls Manual Shift Reverse Lock-Out Switch The reverse lock-out switch prevents the operator from shifting into reverse uninten- tionally. The switch must be manually unlocked before shifting into reverse gear. The lock will automatically re-engage when the transmission is shifted out of reverse gear.
  • Page 58 Features and Controls Manual Shift Deceleration To slow or stop the vehicle, release the throttle lever and apply the brakes smoothly and evenly. As the vehicle slows and engine RPM decreases, disengage the clutch and shift to a lower gear. Be sure the engine RPM has sufficiently decreased before shifting to a lower gear.

  • Page 59: Fuel Tank

    Polaris recommends the use of 91 octane or higher fuel. Do not use E-85 fuel. Fuel Filters The fuel pick-ups have internal fuel filters. Do not attempt to clean the fuel filters. See your Polaris dealer for service if you suspect the fuel filters are plugged.

  • Page 60: Fuel Valve

    Features and Controls Fuel Valve The fuel valve is located on the right side of the Fuel Valve ATV. It has three positions: OFF: For vehicle storage and when transporting. Turn the fuel valve off whenever the vehicle is stored or parked. ON: For normal operation.

  • Page 61: Operation

    Break-In Period The break-in period for your new Polaris ATV is the first three hours of operation, or the time it takes to use 5-6 gallons (20 liters) of fuel. No single action on your part is as impor- tant as following the procedures for a proper break-in.
  • Page 62 Break-In Period Perform the following break-in and maintenance procedures carefully. 1. Fill the fuel tank with gasoline. Always exercise extreme caution whenever han- dling gasoline. 2. Check the oil level. Add the recom- mended oil as needed to maintain the oil level in the proper range.

  • Page 63: Pre-Ride Inspection

    Operation Pre-Ride Inspection Failure to inspect and verify that the ATV is in safe operating condition before operating increases the risk of an accident. Always inspect the ATV before each use to make sure it's in safe operating condition. Brake systems / lever travel Brake fluid Clutch lever Clutch fluid...
  • Page 64 Ensure operation Ensure proper operation Inspect, clean, replace as needed Drain deposits when visible Check operation, apply Polaris dielectric grease to the socket when the lamp is replaced Check operation, adjust brake light switch Wear helmet, goggles, protective clothing Check freeplay. If the tire moves excessively, do not operate.

  • Page 65: Safe Operation Practices

    Operation Safe Operation Practices 1. Complete the recommended safety training before operating this vehicle. See page 10. 2. Do not allow anyone under 16 years of age to operate this vehicle. Do not allow anyone with cognitive or physical dis- abilities to operate this vehicle.
  • Page 66 Safe Operation Practices 8. Drive in a manner appropriate for your skills and operating conditions. Never operate at excessive speeds. Never attempt wheelies, jumps, or other stunts. Never remove your hands from the han- dlebars while operating, and always keep both feet on the footpegs. 9.
  • Page 67 Respect the environment in which you ride. Find out where the desig- nated riding areas are by contacting your Polaris dealer, a local riding club or local officials. Help keep our trails open for recreational vehicle use. As an off-road enthusiast, you repre- sent the sport and can set a good example (or a poor example) for others to follow.

  • Page 68: Trail Etiquette

    Operation Trail Etiquette Always practice good etiquette when riding. Allow a safe distance between your vehicle and other vehicles operating in the same area. Communicate to oncoming operators by signaling the number of vehicles in your group. When stopping, move your vehicle to the edge of the trail as far as possible to allow others to pass safely.

  • Page 69: Starting The Engine

    Operation Starting the Engine The engine can be started when the transmission is in neutral, or while in gear if the clutch is disengaged. If starting a warm engine, do not use the choke. Fuel is injected into the intake passage each time the throttle lever is depressed. Do not depress the throttle lever while starting the engine.
  • Page 70 Repeat until the engine starts. If the engine does not start, review the engine troubleshooting information beginning on page 172. If all conditions are favorable and the engine still does not start, see your Polaris dealer for service.

  • Page 71: Driving Procedure

    Operation Driving Procedure 1. Wear a helmet and eye protection. 2. Sit upright with both feet on the footpegs and both hands on the handlebars. 3. Start the engine and allow it to warm up. 4. Shift the transmission into gear. See page 52. 5.

  • Page 72: Making Turns

    Operation Making Turns Your ATV is equipped with a solid rear axle, which drives both rear wheels equally at all times. The wheel on the outside of the turn travels a greater distance than the inside wheel when turning, and the inside tire slips traction slightly. To turn, steer in the direction of the turn, leaning your upper body to the inside of the turn while supporting your weight on the outer footpeg.

  • Page 73: Driving On Slippery Surfaces

    Driving on Slippery Surfaces Whenever riding on slippery surfaces such as wet trails or loose gravel, or during freezing weather, follow these precautions: 1. Slow down when entering slippery areas. 2. Maintain a high level of alertness, reading the trail and avoiding quick, sharp turns, which can cause skids.
  • Page 74 Operation Driving on Slippery Surfaces 4. Never apply the brakes during a skid. Correct a skid by turning the handlebars in the direction of the skid and shifting your body weight forward. Turn in Sideways direction of skid skid...

  • Page 75: Driving Uphill

    Driving Uphill Braking and handling are greatly affected when operating in hilly terrain. Improper procedure could cause loss of control or overturn. Whenever traveling uphill, follow these precautions: 1. Drive straight uphill. 2. Avoid steep hills (25 ° 3. Always check the terrain carefully before ascending any hill.
  • Page 76 Driving Uphill 5. Keep both feet on the footpegs. 6. Shift body weight uphill. 7. Proceed at a steady rate of speed and throttle opening. Opening the throttle suddenly could cause the ATV to flip over backwards. 8. Never back down a hill. WARNING! Aggressively applying the foot brake when backing down a hill may cause rear tipover.
  • Page 77 Driving on a Sidehill (Sidehilling) Driving on a sidehill is not recommended. Improper procedure could cause loss of control or overturn. Avoid crossing the side of any hill unless absolutely necessary. If crossing a sidehill is unavoidable, follow these precautions: 1.

  • Page 78: Driving Downhill

    Driving Downhill Whenever descending a hill, follow these precautions: 1. Avoid steep hills (25 ° 2. Shift body weight uphill. Transfer your weight to the rear of the vehicle. 3. Drive straight downhill. 4. Slow down. Excessive speed when trav- eling downhill can cause loss of control.

  • Page 79: Turning Around On A Hill

    Operation Turning Around on a Hill If the vehicle stalls while climbing a hill, never back it down the hill! Use the K-turn to turn around: 1. Keep your body weight uphill. 2. Pull in the clutch lever and apply the front and rear brakes. 3.
  • Page 80 Turning Around on a Hill 7. With the front brakes applied, pull in the clutch lever. Use the brakes to slowly allow the vehicle to roll around to your right until it's pointing across the hill or slightly downward. 8. With the front brakes still applied, release the clutch lever and lock the parking brake.

  • Page 81: Parking On A Hill Or Incline

    Operation Parking on a Hill or Incline Avoid parking on a hill or incline if pos- sible. If it's unavoidable, follow these precautions: 1. Turn the engine off. 2. Place the transmission in first gear. 3. Lock the parking brake. 4.

  • Page 82: Driving Over Obstacles

    Driving Over Obstacles Follow these precautions when operating over obstacles: 1. Always check for obstacles before oper- ating in a new area. 2. Look ahead and learn to read the terrain. Be constantly alert for hazards such as logs, rocks and low hanging branches. 3.

  • Page 83: Driving Through Water

    Operation Driving Through Water Polaris does not recommend operating in water deeper than the height of the footpegs. Follow these procedures when operating through water: 1. Determine water depth and current before entering water. 2. Choose a crossing where the water level is lowest and where both banks have gradual inclines.
  • Page 84 Driving Through Water NOTICE: Serious engine damage can result if the vehicle is not thoroughly inspected after operating in water deeper than the footpeg level. As soon as possible, perform the inspections and maintenance services outlined in the periodic maintenance chart beginning on page 85. Engine oil and all grease fittings need special attention.

  • Page 85: Driving In Reverse

    Operation Driving in Reverse Follow these precautions when operating in reverse: 1. Always check for obstacles or people behind the vehicle. 2. Always avoid backing downhill. 3. Back slowly. 4. Apply the brakes lightly for stopping. 5. Avoid turning at sharp angles. 6.

  • Page 86: Emission Control Systems

    Operation on Public Lands in the U.S.A. Your Polaris vehicle has a spark arrestor that was tested and qualified to be in accordance with the USDA Forest Service Standard 5100-1C. Federal law requires that this spark arres- tor be installed and functional when the vehicle is operated on public lands.

  • Page 87: Exhaust Emission Control System

    The engine and related components must be main- tained at Polaris specifications to achieve optimal performance. Engine idle speed is the only adjustment Polaris recommends that the operator perform. Any other adjustments should be performed by an authorized Polaris dealer.

  • Page 88: Maintenance

    Inspect, clean, lubricate, adjust and replace parts as necessary. When inspection reveals the need for replacement parts, use genuine Polaris parts available from your Polaris dealer. Record maintenance and service in the Maintenance Log beginning on page 193.

  • Page 89: Severe Use Definition

    Maintenance Periodic Maintenance Chart The recommended service intervals are based on average riding conditions. Vehicles sub- jected to severe use must be inspected and serviced more frequently. Severe Use Definition • Frequent immersion in mud, water or sand • Racing or race-style high RPM use •...

  • Page 90: Periodic Maintenance Chart

    Periodic Maintenance Chart WARNING Improperly performing the procedures marked with a accident, which may result in serious injury or death. Always have an authorized Polaris dealer perform these services. Maintenance Chart Key Perform these operations more often under severe use.
  • Page 91 Maintenance Periodic Maintenance Chart Item Brake systems/brake fluid Tires Wheels/lug nuts Frame fasteners Coolant Fuel Engine oil Transmission oil Throttle Clutch system/clutch fluid Lights Engine stop switch Steering Maintenance Interval (whichever comes first) Hours Calendar Fuel Used Pre-ride Remarks Check each day before operating the vehicle.
  • Page 92 Idle speed Engine mounting bolts Valve clearance Perform these procedures more often for vehicles subjected to severe use Emission-Related Service Have an authorized Polaris dealer perform these services Use Polaris Premium All Season Grease Maintenance Interval (whichever comes first) Hours Calendar...
  • Page 93 Maintenance Periodic Maintenance Chart Item Brake pad wear Rear sprocket bolts Battery Air filter Oil and filter change Oil screen/drain plug Idle speed Engine mounting bolts Shift lever bolt Valve clearance Clutches Spark plug Maintenance Interval (whichever comes first) Hours Calendar Fuel Used in gallons (liters) Monthly...
  • Page 94 Drive chain(s) Brake pad replacement Coolant strength Perform these procedures more often for vehicles subjected to severe use Emission-Related Service Have an authorized Polaris dealer perform these services Use Polaris Premium All Season Grease Maintenance Interval (whichever comes first) Hours Calendar...
  • Page 95 Maintenance Periodic Maintenance Chart Item Upper steering post (1) Front A-Arms (2) Stabilizer Bar (3) Rear Control Arm Needle Bearings (4) Maintenance Interval (whichever comes first) Hours Calendar Fuel Used in gallons (liters) 12 M Remarks Inspect; tighten fasteners; grease after washing ATV/driving in water Inspect;...
  • Page 96 Cylinder and piston Piston pin circlip groove Perform these procedures more often for vehicles subjected to severe use Emission-Related Service Have an authorized Polaris dealer perform these services Use Polaris Premium All Season Grease Maintenance Interval (whichever comes first) Hours Calendar...
  • Page 97 Maintenance Periodic Maintenance Chart Item Compression ring Oil scraper ring Camshaft Valve spring cap Camshaft bearings Valve springs Valve seats/guides Rocker arm rollers Timing chain Cam chain tensioner Bearings (connecting rod, balance shaft, crankshaft main) Crankshaft run-out Maintenance Interval (whichever comes first) Hours Calendar Fuel Used in gallons (liters)
  • Page 98 Front/rear wheel bearings Toe adjustment Headlight aim Perform these procedures more often for vehicles subjected to severe use Emission-Related Service Have an authorized Polaris dealer perform these services Use Polaris Premium All Season Grease Maintenance Interval (whichever comes first) Hours Calendar...
  • Page 99 Always check and change the engine oil at the intervals outlined in the Periodic Maintenance Chart beginning on page 85. Polaris recommends the use of Polaris PS-4 PLUS Performance Synthetic 2W-50 4-cycle oil or a similar oil designed for use in 4-stroke manual clutch ATV and motorcycle applications.

  • Page 100: Engine Oil Level

    Engine Oil Level Check the oil level before each use of the vehicle. If the engine is cold, the oil level should be visible at the lower edge of the sight glass. If the engine is warm, the oil level should be visible at the center of the sight glass.

  • Page 101: Engine Oil Change

    Maintenance Engine Oil Change Always change the oil at the intervals outlined in the Periodic Maintenance Chart beginning on page 85. Change the oil more frequently on vehicles subjected to severe use. IMPORTANT: Perform the initial break-in oil change after the first three hours of operation. Always change both oil filters and clean the oil screens whenever changing oil.
  • Page 102 Engine Oil Change 1. Position the vehicle on a level surface. 2. Remove the skid plate for better access to the oil drain plug and short screen. 3. Start the engine. Allow it to idle for two to three minutes. Stop the engine. 4.
  • Page 103 Maintenance Engine Oil Change Cleaning the Short Oil Screen Short Oil Screen Plug Front Short Screen O-Rings View from bottom of vehicle...
  • Page 104 Engine Oil Change Cleaning the Short Oil Screen 1. Remove the short oil screen plug at the bottom of the engine. See illustration on preceding page. 2. Remove the short oil screen from the plug. Clean the screen components thoroughly and blow well with compressed air.
  • Page 105 Engine Oil Change Cleaning the Long Oil Screen 1. Remove the long screen plug, located on the side of the engine near the engine number. 2. Remove the oil screen. Clean the screen thoroughly and blow with compressed air. 3. Check the O-rings. If damaged, install new O-rings.
  • Page 106 Engine Oil Change Cleaning the Long Oil Screen 5. Insert the tool through the opening and into the bore of the opposite engine casing wall. Push the oil screen into the casing as far as possible. Remove the tool. NOTICE: An improperly installed oil screen will function poorly and result in increased engine wear.
  • Page 107 Engine Oil Change Changing Oil Filters 1. Place a drain pan under the engine. 2. Remove the four oil filter cover screws (1). Remove the covers. 3. Using circle clip (snap ring) pliers, pull the oil filter inserts (2) out of the housing. 4.
  • Page 108 Engine Oil Change Changing Oil Filters 6. Grease the filter cover O-rings (3). 7. Reinstall the covers and the screws. Tighten screws to 4.5 ft. lbs. (6 Nm). 8. Remove the oil fill plug (4). Add 1.7 qts. (1.6 l) of the recommended engine oil (see page 96).

  • Page 109: Engine Cooling System

    Always follow the manufacturer's mixing recommendations for the freeze protection required in your area. Polaris Premium 60/40 is already premixed and ready to use. Do not dilute with water. See page 170 for the part numbers of Polaris products.

  • Page 110: Coolant Level

    Maintenance Engine Cooling System Coolant Level The recovery bottle is located on the right side of the vehicle under the front fender. If the fluid level is vis- ible at the bottom of the side panel, add 6 oz. (175 ml) of coolant.
  • Page 111 Engine Cooling System Radiator Coolant Level If the recovery bottle has run dry, inspect the level in the radiator and add coolant if necessary. The radiator pressure cap is located on the left side of the vehicle. CAUTION! Escaping steam can cause burns. Never remove the pressure cap while the engine is warm or hot.

  • Page 112: Cooling System Bleeding

    Engine Cooling System Cooling System Bleeding Bleeding the cooling system is required only if the system has been drained for maintenance and/or repair. Always allow the engine to cool sufficiently before removing the radiator pres- sure cap. 1. Remove the pressure cap. 2.

  • Page 113: Air Filter Systems

    Maintenance Air Filter Systems Refer to the illustrations on page 111. 1. Remove the seat. 2. Release the airbox cover clips and remove the cover. 3. Loosen the filter clamp. Remove the air filter from the box. 4. Locate the retaining spring. 5.
  • Page 114 Maintenance Air Filter Systems Step 3 Step 4 Step 5 Step 6 Step 7...

  • Page 115: Idle Speed

    3. Start the engine and allow it to idle for five min- utes, or until operating temperature is reached. 4. Turn the idle adjusting wheel (1) until idle speed reaches 1500-1600 RPM. 5. If idle speed is unsatisfactory after performing this procedure, see your Polaris dealer for information about jetting changes.

  • Page 116: Carburetor Draining

    Maintenance Carburetor Carburetor Draining Drain the carburetor float bowl at the intervals outlined in the Periodic Maintenance Chart beginning on page 85. Always drain the bowl after exposure to wet conditions. Perform this procedure when the engine is cool. 1. Turn the fuel valve off. 2.

  • Page 117: Carburetor Jetting

    Maintenance Carburetor Jetting Carburetor re-jetting can be performed to compensate for altitude and/or temperature changes. If the vehicle is to be operated at various altitudes and temperatures, certain adjust- ments can be made to improve its operation and driveability. Above 6000 feet (1800 m) the engine air/fuel mixture becomes overly rich.

  • Page 118: Headlight Adjustment

    Lights Headlight Adjustment 1. Position the vehicle on a level surface with the headlight approximately 25 ft. (7.6 m) from a flat wall. 2. Measure the distance from the floor to the center of the headlight and make a mark on the wall at the same height.
  • Page 119 Lights 4. Observe the headlight aim on the wall. The most intense part of the headlight beam should be aimed 2" (5 cm) below the mark placed on the wall. Include rider weight on the seat when measuring. 5. Loosen the pivot screw and adjust the beam to the desired position.

  • Page 120: Headlight Lamp Replacement

    Maintenance Lights Headlight Lamp Replacement When servicing a halogen lamp, avoid touching the lamp with bare fingers. Oil from your skin leaves a residue, causing a hot spot that will shorten the life of the lamp. If fingers do touch a lamp, clean it with denatured alcohol. 1.
  • Page 121 Maintenance Lights Headlight Assembly Replacement 1. Remove the front cover. 2. Remove the wire harness connector from the headlights. 3. Remove the two retaining brackets and the adjuster screw. 4. Remove the headlamp. 5. Install the new headlamp, placing it in the slots on the frame tabs. Secure the headlamp with the retaining brackets.

  • Page 122: Brake Light Adjustment

    Lights Brake Light Adjustment Check the rear brake light for proper operation before each use of the vehicle. 1. Turn the ignition key on. 2. Lightly apply and release the foot brake several times. A properly operating rear brake light will immedi- ately flash on and off with each movement of the brake pedal.
  • Page 123 Front Cab/Side Panel Removal The front cab and side panel assembly is removed in one piece. 1. Remove the seat. 2. Remove the two front cover screws and remove the front cover. 3. Remove the eight side panel screws (four on each side). 4.
  • Page 124 Rear Cab Removal 1. Unlatch and remove the seat. 2. Remove the two lower bolts (1) on the rear fenders of the cab. 3. Remove the two bolts and grommets (2) on the top of the cab. 4. Remove the two bolts (3) at the rear cab-to-front-cab joint.

  • Page 125: Spark Plugs

    Refer to the specifications section beginning on page 168 for recommended spark plug type and gap NOTICE: Using non-recommended spark plugs can result in serious engine damage. Always use Polaris-recommended spark plugs. Spark plug condition is indicative of engine operation. The spark plug firing end condition should be read after the engine has been warmed up and the vehicle has been driven at higher speeds.
  • Page 126 Maintenance Spark Plugs Normal Plug The normal insulator tip is gray, tan or light brown. There will be few combustion deposits. The electrodes are not burned or eroded. This indicates the proper type and heat range for the engine and the service. The tip should not be white.

  • Page 127: Spark Arrestor Clean-Out

    Maintenance Spark Arrestor Clean-Out WARNING Failure to heed the following warnings while servicing the spark arrestor could result in serious injury or death. The exhaust system can get extremely hot. Do not perform service on the spark arrestor while the system is hot. Allow components to cool sufficiently before proceeding. Remove any combustible materials from the area.
  • Page 128 Spark Arrestor Clean-Out To remove accumulated carbon, clean the spark arrestor at the intervals recommended in the Peri- odic Maintenance Chart beginning on page 85. 1. Remove the retaining screw and remove the screen from the end of the muffler. 2.

  • Page 129: Vehicle Immersion

    Maintenance Vehicle Immersion If the vehicle tips or overturns in water deeper than the footpeg level, or if the engine stops during or after operating in water, restarting WILL result in serious engine damage. Trans- port the vehicle to your dealer for service before restarting the engine. If this is not possible, follow the vehicle immersion inspection and drying procedures outlined below.
  • Page 130 Maintenance Vehicle Immersion 1. Turn the fuel valve off. 2. Drain water from the air box and clean the air filter. See page 110. 3. Drain the carburetor bowl. See page 113. 4. Remove the spark plug. See page 122. WARNING! Fluids will be ejected through the spark plug hole and may cause serious injury to face or other body parts.
  • Page 131 Vehicle Immersion 6. Press and hold the starter button for 10 second intervals for about one minute or until water vapor is no longer ejecting from the spark plug hole. 7. Check the oil level. If the level is higher than the pre-ride inspection level, water has entered the crankcase.
  • Page 132 Maintenance Battery WARNING Improperly connecting or disconnecting battery cables can result in an explosion and cause serious injury or death. When removing the battery, always disconnect the negative (black) cable first. When reinstalling the battery, always connect the negative (black) cable last. The sealed battery is already filled with electrolyte and has been sealed and fully charged at the factory.

  • Page 133: Battery Removal

    Maintenance Battery Storage Whenever the vehicle is not used for a period of three months or more, remove the battery from the vehicle, ensure that it's fully charged, and store it out of the sun in a cool, dry place. Check battery voltage each month during storage and recharge as needed to maintain a full charge.

  • Page 134: Battery Installation

    Maintenance Battery Installation Always install a fully charged battery. Using a new battery that has not been fully charged can damage the battery and result in a shorter life. It can also hinder vehicle performance. If recharging is necessary, use a .5 amp battery charger. 1.
  • Page 135 Maintenance Battery Charging (Sealed Battery) On a sealed battery, the sealing strip cannot be removed. Use a voltmeter or multimeter to measure DC voltage. A fully charged battery will register 12.8 V or higher. If the voltage is less than 12.8 volts, recharge the battery. WARNING! An overheated battery could explode, causing severe injury or death.
  • Page 136 See your Polaris dealer for inspection of the voltage regulator and generator. When using an automatic charger such as the Polaris Battery Tender, refer to the manufac- turer's instructions for recharging. When using a constant current charger, use the guidelines...
  • Page 137 Maintenance Battery Charging (Sealed Battery) Always verify battery condition before and 1-2 hours after the end of charging. State of Voltage Charge 100% 12.8-13.0 volts 75%-100% 12.5-12.8 volts 50%-75% 12.0-12.5 volts 25%-50% 11.5-12.0 volts 0%-25% 11.5 volts or less Action None, check at 3 months from date of manufacture May need slight charge, if no...

  • Page 138: Tire Tread Depth

    Maintenance Tires WARNING Operating your ATV with worn tires, improperly inflated tires, non-standard tires or improperly installed tires will affect vehicle handling and could cause an accident resulting in serious injury or death. Always follow all tire maintenance procedures as outlined in this manual and on the labels on the vehicle. Always use original equipment size and type when replacing tires.

  • Page 139: Wheel Removal

    Wheel Hub Tightening Front wheel bearing tightness and spindle nut retention are critical component operations. All service must be performed by your authorized Polaris dealer. Wheel Removal 1. Stop the engine. Place the transmission in gear. Lock the parking brake.

  • Page 140: Wheel Installation

    Wheel Installation 1. Place the transmission in gear. Lock the parking brake. 2. Place the wheel on the wheel hub with the valve stem toward the outside and rotation arrow on the tire pointing toward forward rotation. 3. Install the wheel bolts and finger tighten them. 4.

  • Page 141: Boot Inspection

    Boot Inspection Before Operating Inspect the boots before operating the vehicle. If a boot is torn, punctured or leaking fluid, see your Polaris dealer for service or replacement. After Operating Inspect the boots after operating the vehicle. If a boot is bulging or ballooned, perform the boot burping procedure on page 139.

  • Page 142: Boot Burping

    Boot Burping 1. Using a needle nose pliers or boot clamp removal tool, remove the small boot clamp (1) from the inboard boot. Do not use any tools that may damage the boot. 2. Slide the free end of the boot two inches toward the center of the vehicle and lift the boot away from the shaft to allow excess air to escape (2).

  • Page 143: Clutch System Bleeding

    Clutch System Bleeding Always bleed the clutch system at the intervals out- lined in the Periodic Maintenance Chart beginning on page 85. Always bleed the clutch system any time the clutch lever feels unresponsive. Always use the recommended fluid when bleeding the clutch system.
  • Page 144 Clutch System Bleeding 4. Remove the bleeder screw (2) from the slave cylinder. 5. Press fluid into the system until the fluid runs out of the hole (3) in the master cylinder without producing bubbles. TIP: Extract fluid from the master cylinder during the process to prevent overflowing. 6.
  • Page 145 Maintenance Throttle Lever Freeplay Periodically check throttle lever freeplay. Maintain freeplay between 1/16" and 1/8" (1.5 - 3 mm). If adjustments are needed, use the procedure on page 143. " 1/16 - 1/8" (1.5 - 3 mm)
  • Page 146 Improper adjustment of throttle cable freeplay can result in loss of control, which could result in serious injury or death. Polaris recommends that this procedure be performed by a Polaris dealer to ensure that it's done correctly. Mechanically knowledgeable persons who perform this procedure must follow the adjustment procedures exactly.
  • Page 147 Maintenance Brakes Under normal operation, the diaphragm extends into the reservoir as fluid level drops. If the fluid level is low and the diaphragm is not extended, a leak is likely and the diaphragm should be replaced. To ensure proper diaphragm operation, always fill the reservoir as needed whenever the cover is loosened or removed.
  • Page 148 Brakes 1. Always maintain brake fluid at the recommended level. See pages 48-49. 2. Check the brake system for fluid leaks. 3. Check the brakes for excessive travel or spongy feel. 4. Check the friction pads for wear, damage and looseness. 5.

  • Page 149: Toe Alignment

    WARNING! Severe injury or death can result from improper toe alignment and adjustment. Do not attempt to adjust tie rod alignment. All tie rod adjustments should be performed by an authorized Polaris dealer. 1. Position the vehicle on a level surface. Ensure the vehicle is at the proper ride height by placing a rider on the vehicle.
  • Page 150 8. The recommended toe alignment is 0" to 1/16" (0-1.6 mm) toe out. This means that the front measurement should be 0" to 1/16" (0-1.5 mm) greater than the rear mea- surement. 9. If you discover improper alignment, see your Polaris dealer for service.

  • Page 151: Chain Tension

    Chain Tension CAUTION! Never adjust or operate the vehicle with the rear drive chain too loose or too tight. Severe damage to the transmission and drive components can result. Check the amount of chain slack by moving the vehicle slightly forward to remove slack at the top side of the chain.
  • Page 152 Chain Tension 3. Tighten the pivot mounting bolts to 30 ft. lbs. (40 Nm). 4. Torque the chain adjusting bolt to 17 ft. lbs. (23 Nm). 5. Check sprocket bolts to make sure the retainer tabs fit tightly against the bolt heads.

  • Page 153: Handlebar Adjustment

    Improper adjustment of the handlebars or incorrect torquing of the adjuster block tightening bolts can cause limited steering or loosening of the handlebars, resulting in loss of control. Follow the adjustment procedures exactly, or see your Polaris dealer for service. The handlebars can be adjusted for rider preference.

  • Page 154: Steering Inspection

    Steering Inspection Check the steering assembly periodically for loose nuts and bolts. If loose nuts and bolts are found, or if you notice any freeplay in the steering post, see your Polaris dealer for service before operating the vehicle. Camber and Caster...

  • Page 155: Front Suspension

    Maintenance Front Suspension Suspension Set-Up 1. Position the vehicle on a level surface. 2. Stop the engine. 3. Elevate the front of the vehicle by placing a suitable stand under the frame. The tires should be barely touching the ground and the suspension should be at full rebound.
  • Page 156 Front Suspension Suspension Set-Up 6. Place the transmission in neutral and slowly roll the machine forward and rearward at least ten feet (3 m) without lifting or pushing down on the suspension. 7. Turn the handlebars fully to the left and right. 8.

  • Page 157: Spring Preload

    WARNING! Uneven adjustment may cause poor handling of the ATV, which could result in an accident and serious injury or death. Always adjust both the left and right spring preloads equally or have your Polaris dealer perform the adjustments.
  • Page 158 Front Suspension Spring Preload 1. Raise and safely support the front of the vehicle off the ground to allow the suspension to fully extend. 2. Loosen the jam nut. 3. Turn the adjusting ring clockwise to increase preload. Turn the ring counter-clockwise to decrease preload.

  • Page 159: Rear Suspension

    Maintenance Rear Suspension Suspension Set-Up 1. Position the vehicle on a level surface. 2. Stop the engine. 3. Elevate the rear of the vehicle by placing a suitable stand under the frame. The tires should be barely touching the ground and the suspension should be at full rebound.
  • Page 160 Rear Suspension Suspension Set-Up 5. Remove the stand and have a rider sit comfortably on the seat with hands on the handle- bars. 6. Place the transmission in neutral and slowly roll the machine forward and rearward at least ten feet (3 m) without lifting or pushing down on the suspension. 7.
  • Page 161 Maintenance Rear Suspension The rear suspension spring preload and shock compression damping may be adjusted to suit different riding conditions and operator weight. Spring Preload 1. Raise and safely support the rear of the vehicle off the ground to allow the suspension to fully extend. 2.

  • Page 162: Compression Damping

    Rear Suspension Compression Damping The compression damping clickers are located on the bottom of the shocks (on the lower clevis). Use a screwdriver to make adjustments. To set the shock at the firmest setting, turn the screw clockwise until it stops (fully closed position). From this position, turn the screw counter-clockwise to decrease compression damping.

  • Page 163: Washing The Vehicle

    Do not allow these types of products to contact the vehicle. Washing the Vehicle The best and safest way to clean your Polaris vehicle is with a garden hose and a pail of mild soap and water. 1. Use a professional-type washing cloth, cleaning the upper body first and the lower parts last.
  • Page 164 Maintenance Cleaning Washing the Vehicle Washing Tips • Avoid the use of harsh cleaners, which can scratch the finish. • Do not use a power washer to clean the vehicle. • Do not use medium to heavy duty compounds on the finish. •...
  • Page 165 If a high pressure water system is used for cleaning (not recommended), exercise extreme caution. The water may damage components and could remove paint and decals. If warning and safety labels are damaged, contact your Polaris dealer for free replacement. Avoid direct- ing the water stream at the following items: •...

  • Page 166: Battery Storage

    Polishing Polaris recommends the use of common household aerosol furniture polish for polishing the finish on your Polaris vehicle. Follow the instructions on the container. Polishing Tips • Avoid the use of automotive products, some of which can scratch the finish of your vehi- cle.
  • Page 167 Maintenance Storage Engine Oil Change the oil and both filters. Clean the oil screens. See page 98. Air Filter / Air Box Inspect and clean (or replace) the air filter. Clean the air box. Drain the sediment tube. Fluid Levels Inspect fluid levels.
  • Page 168 Stabilize the Fuel 1. Fill the fuel tank with fuel. 2. Add Polaris Carbon Clean Fuel Treatment or Polaris Fuel Stabilizer. Follow the instruc- tions on the container for the recommended amount. Carbon Clean removes water from fuel systems, stabilizes fuel and removes carbon deposits from pistons, rings, valves and exhaust systems.
  • Page 169 Maintenance Storage Lubricate Inspect all cables and lubricate all areas of the vehicle as recommended in the Periodic Main- tenance Chart beginning on page 85. Storage Area/Covers 1. Make sure tire pressure is at specification. 2. Be sure the storage area is well ventilated. 3.

  • Page 170: Transporting The Atv

    Maintenance Transporting the ATV Follow these procedures when transporting the vehicle. 1. Stop the engine. 2. Place the transmission in first gear. 3. Lock the parking brake. 4. Remove the key to prevent loss during transporting. 5. Secure the fuel cap, oil cap and seat. 6.

  • Page 171: Specifications

    Specifications Max. Weight Capacity 215 lbs./97.5 kg Dry Weight 389 lbs./176 kg Fuel Capacity 3.1 gal./11.7 l Overall Length 71.5 in./182 cm Overall Width 47.5 in./121 cm Overall Height 45 in./114 cm Wheelbase 51 in./130 cm Ground Clearance 11.5 in./29 cm Min.

  • Page 172: Jetting Chart

    Driving System Type Rear Two-Wheel Drive Shift Type 5-Speed Manual Shift Primary Ratio 2.516 Gear Ratio - 1st 2.500 Gear Ratio - 2nd 1.941 Gear Ratio - 3rd 1.579 Gear Ratio - 4th 1.333 Gear Ratio - 5th 1.130 Gear Ratio - Reverse 2.429 Jetting Chart ALTITUDE...

  • Page 173: Polaris Products

    Part Number Description 2876244 PS-4 PLUS Performance Synthetic 2W-50 4-Cycle Oil (qt.) 2876245 PS-4 PLUS Performance Synthetic 2W-50 4-Cycle Oil (gal.) 2871312 Grease Gun Kit, Premium All Season (3 oz.) 2871322 Premium All Season Grease (3 oz. cartridge) 2871423 Premium All Season Grease (14 oz. cartridge) 2871460 Starter Drive Grease (2 oz.) 2871329...
  • Page 174 Part Number Description 2871323 60/40 Coolant (gal.) 2871534 60/40 Coolant (qt.) 2871326 Carbon Clean Plus (12 oz.) 2870652 Fuel Stabilizer (16 oz.) 2872189 DOT4 Brake Fluid (12 oz.) 2876335 Hydraulic Clutch Oil (qt.) Coolant Additives / Miscellaneous...

  • Page 175: Troubleshooting

    See your Polaris dealer if you're unable to identify solutions using the following charts. Engine Turns Over, Fails to Start Possible Cause Out of fuel Water is present in carburetor or fuel supply Fuel valve is turned off Engine is cold...
  • Page 176 Troubleshooting Solution Inspect, clean and/or replace spark plugs See your Polaris dealer Engage starter 2 times for 5 seconds each, then restart. If engine fails to start, inspect, clean and/or replace spark plugs. Recharge battery to 12.8 VDC...
  • Page 177 Possible Cause Poor quality or low octane fuel Incorrect ignition timing Incorrect spark plug gap or heat range Solution See Polaris dealer for replacement Recharge battery to 12.8 VDC Check all connections and tighten Check all connections and tighten Solution...
  • Page 178 Mechanical failure Troubleshooting Solution Inspect, clean and/or replace spark plugs Set gap to specs or replace plugs Replace with new fuel Inspect system for leaks; see your Polaris dealer See your Polaris dealer See your Polaris dealer See your Polaris dealer...
  • Page 179 Kinked or plugged fuel vent line Old or non-recommended fuel Solution Inspect, clean and/or replace spark plug See your Polaris dealer Set gap to specs or replace plug Check all connections and tighten See your Polaris dealer Replace with new fuel Recharge battery to 12.8 VDC or replace...
  • Page 180 Electronic throttle control malfunction Incorrect idle adjustment Clogged idle jet Other mechanical failure Solution Inspect and clean or replace See your Polaris dealer Adjust idle speed or see your Polaris dealer Disassemble carburetor and clean the jets See your Polaris dealer...
  • Page 181 Plugged, dirty or wet air filter Solution Add or change fuel, clean the fuel system Replace with recommended fuel Replace with recommended fuel See your Polaris dealer See your Polaris dealer Solution Inspect, clean and/or replace spark plugs Replace with recommended octane fuel...
  • Page 182 Excessive oil in system Use of non-recommended oil (too thin) Troubleshooting Solution Clean and/or replace needle valve Tighten jets See your Polaris dealer Solution Install a new hose Check oil level, maintain at recommended level Replace with a recommended oil...
  • Page 183 Solution Turn the fuel valve to reserve, refuel Clean fuel system and carburetor Inspect and clean or replace See your Polaris dealer See your Polaris dealer Clean radiator screen and core if equipped Clean engine exterior See your Polaris dealer...
  • Page 184 Inspect and replace Replace with new fuel Inspect, clean and/or replace spark plugs Inspect, clean and/or replace spark plugs See your Polaris dealer Set gap to specs or replace plugs Check all connections and tighten Recharge battery to 12.8 VDC...
  • Page 185 Operate at a faster speed to increase air flow Bleed the cooling system Drain and replace coolant with recommended coolant Shorten or replace hose See your Polaris dealer Replace fuse and check fan for proper operation or see your Polaris dealer...
  • Page 186 Faulty exhaust system Valve gap is too small Faulty ignition timing Troubleshooting Solution Clean fuel system and carburetor Replace the float Inspect and clean or replace Check system for damage; see your Polaris dealer Adjust valve gap See your Polaris dealer...

  • Page 187: Warranty

    Polaris dealer. REGISTRATION At the time of sale, the Warranty Registration Form must be completed by your dealer and submitted to Polaris within ten days. Upon receipt of this registration, Polaris will record the registration for warranty. No verification of registration will be sent to the purchaser as the copy of the Warranty Registration Form will be the warranty entitlement.
  • Page 188 This warranty does not cover the use of unauthorized lubricants, chemicals, or fuels that are not compatible with the ATV. The exclusive remedy for breach of this warranty shall be, at Polaris' exclusive option, repair or replace- ment of any defective materials, or components or products. THE REMEDIES SET FORTH IN THIS WAR- RANTY ARE THE ONLY REMEDIES AVAILABLE TO ANY PERSON FOR BREACH OF THIS WARRANTY.
  • Page 189 ALL IMPLIED WARRANTIES (INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE) ARE LIMITED IN DURATION TO THE ABOVE SIX MONTH WARRANTY PERIOD. POLARIS FURTHER DISCLAIMS ALL EXPRESS WARRANTIES NOT STATED IN THIS WARRANTY. Some states do not allow limitations on how long an...
  • Page 190 HOW TO OBTAIN WARRANTY SERVICE If your ATV requires warranty service, you must take it to a Polaris dealer authorized to repair Polaris ATVs. When requesting warranty service you must present your copy of the Warranty Registration form to the dealer.
  • Page 191 LETIN COVERAGE ON THIS VEHICLE IF IT IS SOLD OUTSIDE THE COUNTRY OF THE SELLING DEALER'S AUTHORIZED LOCATION. This policy does not apply to vehicles that have received authorization for export from Polaris Industries. Dealers may not give authorization for export. You should consult an authorized dealer to determine this vehicle's war- ranty or service bulletin coverage if you have any questions.
  • Page 192 In the country where your vehicle was purchased: Warranty or Service Bulletin repairs must be done by an authorized Polaris dealer. If you move or are traveling within the country where your vehicle was purchased, Warranty or Service Bulletin repairs may be requested from any authorized Polaris dealer who sells the same line as your vehicle.

  • Page 193: Polaris Products

    EXPORTED VEHICLES How to Get Service If Purchased From A Private Party: If you purchase a Polaris product from a private citizen outside of the country in which the vehicle was originally purchased, all warranty coverage will be denied. Notice If your vehicle is registered outside of the country where it was purchased, and you have not followed the proce- dure set out above, your vehicle will no longer be eligible for warranty or service bulletin coverage of any kind.
  • Page 194 Polaris standard limited warranty for this vehicle. Polaris warrants that this vehicle is; (1) designed, built, and equipped to conform at the time of initial sale with the requirements of 40 CFR 1051 and, (2) free from defects in materials and workmanship that may keep it from meeting these requirements.
  • Page 195 Warranty U.S.A. EPA Emissions Limited Warranty The exclusive remedy for breach of this limited warranty shall be, at the exclusive option of Polaris, repair or replacement of any defective materials, components or products. THE REMEDIES SET FORTH IN THIS LIM- ITED WARRANTY ARE THE ONLY REMEDIES AVAILABLE TO ANY PERSON FOR BREACH OF THIS WARRANTY.

  • Page 196: Maintenance Log

    Present this section of your manual to your dealer each time your vehicle is serviced. This will provide you and future owners with an accurate log of maintenance and services performed. DATE SERVICE INTERVAL (HOURS) 3 Hours (Break-in) TECHNICIAN SERVICE PERFORMED / COMMENTS Maintenance Log...
  • Page 197 Maintenance Log DATE SERVICE INTERVAL (HOURS) TECHNICIAN SERVICE PERFORMED / COMMENTS...
  • Page 198 Maintenance Log DATE SERVICE TECHNICIAN SERVICE PERFORMED / COMMENTS INTERVAL (HOURS)
  • Page 199 Maintenance Log DATE SERVICE TECHNICIAN SERVICE PERFORMED / COMMENTS INTERVAL (HOURS)

  • Page 200: Index

    Age Restrictions ....15 Air Filter Systems ..110-111 Battery Charging ... . . 132-134 Installation .
  • Page 201 Index Fluid Brake ....48-49 Clutch ....43 Foot Brake .
  • Page 202 Periodic Maintenance Chart . . . 85-95 Polaris Products ... . . 170 Polishing ....163 Pre-Ride Inspection.
  • Page 203 Index Side Panel Removal ... 120 Sidehilling ....74 Signal words....6 Spark Arrestor Clean-Out.

This manual is also suitable for:

2009 outlaw 525 irs

Table of Contents