Download  Print this page

Technical Alarm Messages (inops) - Philips IntelliVue MX800 Instructions For Use Manual

Patient monitoring.
Hide thumbs
   
1
2
Table of Contents
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460

Advertisement

3 Patient Alarms and INOPs
Alarm Message
***BRADY/P xxx<yyy
***BRADY xxx < yyy
***<Pressure>
DISCONNECT
**ST MULTI <n>,<n>
**ST MULTI
at Information Center
***TACHY xxx > yy
***TACHY/P xxx>yy
or
***TACHY xxx > yy

Technical Alarm Messages (INOPs)

If an INOP interrupts monitoring and alarm detection, the measurement numeric will be replaced
-?-
by
. If an INOP may lead to unreliable measurement values, a
The measurement labels and abbreviations for pressure, temperature, SpO
messages are explained in the individual measurement chapters.
Monitor INOPs
INOP Message, Indication
!! CHECK PAIRING
INOP tone
Bad Server Link
INOP tone
CENTRAL: TELE ONLY
INOP tone
Check Alarm Lamps
INOP tone
Check DrugSettings
INOP tone
!!CHECK ECG SOURCE
INOP tone
68
From
Condition
Press, SpO
The heart rate from the Pulse signal has fallen
2
below the bradycardia limit. xxx denotes the
lowest measured value; yyy is the bradycardia
limit.
PRESS
The pressure is non-pulsatile and the mean
pressure is continuously less than 10mmHg
(1.3kPa). This alarm occurs only with arterial
pressures (P, ABP, ART, Ao, BAP, FAP, PAP,
UAP, P1, P2, P3, P4).
ECG/ST
The ST depression or elevation is outside of
the limit in two or more leads <n> and <n>
ECG/ST
The ST depression or elevation is outside of
the limit in two or more leads. Check on the
monitor
ECG
The tachycardia limit has been exceeded
Press, SpO
, ECG The tachycardia limit has been exceeded. xxx
2
denotes the highest measured value; yy is the
tachycardia limit.
What to do
There is a problem with device pairing. Check that the monitor and telemetry device are correctly
paired.
1) An MMS with an incompatible software revision is connected to the monitor. This combination
does not allow monitoring, OR
2) You cannot use this combination of monitor, MMS and cable. Switch off the monitor and contact
your service personnel.
System connectivity via telemetry device is limited (No alarms, only local numerics) when in
companion mode and host monitor does not have system connectivity. Only telemetry device
parameters can be displayed at central station.
Perform a visual check of the alarm lamp to establish whether there is a problem. Contact your service
personnel to check the internal connections to the alarm lamps.
There was a problem loading the drug settings. Check that the settings are complete and correct.
The telemetry device and the monitor both have valid ECG signals. Unpair the telemetry device and
the monitor if they are no longer used for the same patient.
Indication
numeric flashes and alarm limit is
highlighted, red alarm lamp, alarm
tone
numeric flashes, red alarm lamp,
alarm tone
numeric flashes, yellow alarm lamp,
alarm tone
(on monitor) numeric flashes,
yellow alarm lamp, alarm tone
numeric flashes and alarm limit is
highlighted, red alarm lamp, alarm
tone
numeric flashes, alarm limit is
highlighted, red alarm lamp, alarm
tone
?
appears next to the numeric.
, and VueLink INOP
2

Advertisement

Table of Contents

Comments to this Manuals

Symbols: 0
Latest comments: