Download Print this page

Hitachi WJ200-004M Quick Reference Manual page 6

Wj200 series
Hide thumbs

Advertisement

Item
Intelligent input terminal
Seven terminals,
sink/source changeable
by a short bar
68 functions assignable
Output
Intelligent output terminal
signal
48 functions assignable
Monitor output (analog)
Pulse train output
(0~10Vdc, 32kHz max.)
Alarm output contact
Other functions
Protective function
Operating
Temperature
environment
Humidity
FW (forward run command), RV (reverse run command), CF1~CF4 (multi-stage
speed setting), JG (jog command), DB (external braking), SET (set second
motor), 2CH (2-stage accel./decel. command), FRS (free run stop command),
EXT (external trip), USP (startup function), CS (commercial power switchover),
SFT (soft lock), AT (analog input selection), RS (reset), PTC (thermistor thermal
protection), STA (start), STP (stop), F/R (forward/reverse), PID (PID disable),
PIDC (PID reset), UP (remote control up function), DWN (remote control down
function), UDC (remote control data clear), OPE (operator control), SF1~SF7
(multi-stage speed setting; bit operation), OLR (overload restriction), TL (torque
limit
enable),
TRQ1
changeover2), BOK (Braking confirmation), LAC (LAD cancellation), PCLR
(position deviation clear), ADD (add frequency enable), F-TM (force terminal
mode), ATR (permission of torque command input), KHC (Cumulative power
clear), MI1~MI7 (general purpose inputs for EzSQ), AHD (analog command
hold), CP1~CP3 (multistage-position switches), ORL (limit signal of zero-return),
ORC (trigger signal of zero-return), SPD (speed/position changeover),
GS1,GS2 (STO inputs, safety related signals), 485 (Starting communication
signal), PRG (executing EzSQ program), HLD (retain output frequency), ROK
(permission of run command), EB (rotation direction detection of B-phase),
DISP (display limitation), NO (no function)
RUN (run signal), FA1~FA5 (frequency arrival signal), OL,OL2 (overload
advance notice signal), OD (PID deviation error signal), AL (alarm signal), OTQ
(over/under torque threshold), UV (under-voltage), TRQ (torque limit signal),
RNT (run time expired), ONT (power ON time expired), THM (thermal warning),
BRK (brake release), BER (brake error), ZS (0Hz detection), DSE (speed
deviation excessive), POK (positioning completion), ODc (analog voltage input
disconnection), OIDc (analog current input disconnection), FBV (PID second
stage output), NDc (network disconnect detection), LOG1~LOG3 (Logic output
signals), WAC (capacitor life warning), WAF (cooling fan warning), FR (starting
contact), OHF (heat sink overheat warning), LOC (Low load), MO1~MO3
(general outputs for EzSQ), IRDY (inverter ready), FWR (forward operation),
RVR (reverse operation), MJA (major failure), WCO (window comparator O),
WCOI (window comparator OI), FREF (frequency command source), REF (run
command source), SETM (second motor in operation), EDM (STO (safe torque
off) performance monitor), OP (option control signal), NO (no function)
Output freq., output current, output torque, output voltage, input power, thermal
load ratio, LAD freq., heat sink temperature, general output (EzSQ)
[PWM output]
Output freq., output current, output torque, output voltage, input power, thermal
load ratio, LAD freq., heat sink temperature, general output (EzSQ)
[Pulse train output]
Output frequency, output current, pulse train input monitor
ON for inverter alarm (1c contacts, both normally open or closed available.)
Free-V/f, manual/automatic torque boost, output voltage gain adjustment, AVR
function, reduced voltage start, motor data selection, auto-tuning, motor
stabilization control, reverse running protection, simple position control, simple
torque control, torque limiting, automatic carrier frequency reduction, energy
saving operation, PID function, non-stop operation at instantaneous power
failure, brake control, DC injection braking, dynamic braking (BRD), frequency
upper and lower limiters, jump frequencies, curve accel and decel (S, U,
inversed U,EL-S), 16-stage speed profile, fine adjustment of start frequency,
accel and decel stop, process jogging, frequency calculation, frequency
addition, 2-stage accel/decel, stop mode selection, start/end freq., analog input
filter, window comparators, input terminal response time, output signal
delay/hold function, rotation direction restriction, stop key selection, software
lock, safe stop function, scaling function, display restriction, password function,
user parameter, initialization, initial display selection, cooling fan control,
warning, trip retry, frequency pull-in restart, frequency matching, overload
restriction, over current restriction, DC bus voltage AVR
Over-current, over-voltage, under-voltage, overload, brake resistor overload,
CPU error, memory error, external trip, USP error, ground fault detection at
power on, temperature error, internal communication error, driver error,
thermistor error, brake error, safe stop, overload at low speed, modbus
communication error, option error, encoder disconnection, speed excessive,
EzSQ command error, EzSQ nesting error, EzSQ execution error, EzSQ user
trip
Operating (ambient): -10 to 40°C(*8), / Storage: -20 to 65°C(*9)
20 to 90% humidity (non-condensing)
5
General Specifications
(torque
limit
changeover1),
TRQ2
(torque
limit

Advertisement

loading

  Related Manuals for Hitachi WJ200-004M

This manual is also suitable for:

Wj200-007m