Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Planet VIP-150T
Summary of Contents for Planet VIP-150T
- Page 1 SIP IP Phone -- with PSTN Connectivity User’s Manual...
-
Page 2: Table Of Contents
1.1.2 Back View ... 4 1.1.3 Specification of connector ... 4 1.2 Software Features and Specification ... 5 Chapter 2 Configuring the VIP-150T through LCD Phone menus ...7 2.1 Initialize VIP-150T ... 7 2.2 LCD Menu Configuration... 8 Chapter 3 Configuring the VIP-150T through Web Pages...14 Step 1. - Page 3 4.18 [bureau] command ... 41 4.19 [rom] command ... 41 4.20 [passwd] command ... 42 Chapter 5 Upgrading Software on the VIP-150T ...44 5.1 From LCD Phone Menu ... 44 5.2 Web Management ... 45 5.3 Remote Control: Telnet... 45...
-
Page 4: Chapter 1 Overview Of The Vip-150T
Carrier Company to provide VoIP services to residential and SOHO application. VIP-150T is also an integrated Analog Phone provides IP call or PSTN call selection. When external power is down, it can be a Plain Old Telephone set (POTs). - Page 5 MUTE: Mute the voice of MIC and let others can’t hear from user in communication. PSTN: Press PSTN to switch VIP-150T as PSTN or IP Phone Mode. In PSTN mode, “PSTN” characters will be displayed on LCD left bottom side, then users can dial out as if standard telephone set in PSTN;...
- Page 6 + And -: Adjust the voice volume heard of communication. SPEAKER: Hand free mode. User can talk without picking up handset. All function keys mentioned above (except dialing keypad) are effective only in IP Phone mode. (**) Note: PLANET VIP-150T User’s Manual hearing dial tone.
-
Page 7: Back View
There are two LED indicated lights: LINK/ACT and 10/100 for LAN port and PC port. When network status is regular, LED of LINK/ACT will light on; when VIP-150T is transmitting or receiving data, LED will be flashing; when transmit Note: rate is in 10 mbps or 100mbps, LED of 10/100 will light off or light on. -
Page 8: Software Features And Specification
Ten configurable speed dials Network Supported Fixed IP Dynamic Host Configuration Protocol (DHCP) PPPoE connection (When PPPoE disconnect, VIP-150T can automatically re-connect) Behind NAT IP Sharing Device Support QOS by setting DSCP (Differentiated Service Code Point) parameters of VoIP packet Support 802.1p1q (VLAN) (**) - Page 9 Dial path selection (PSTN or IP mode) Support DNS server inquiry Management Features: Software Upgrade: TFTP/FTP download Three easy ways for system configuration LCD Front Panel Web Browser TELNET Environmental Humidity: 10 to 90 % (Non-condensing) Operational Temperature: 0 to +40 C PLANET VIP-150T User’s Manual...
-
Page 10: Chapter 2 Configuring The Vip-150T Through Lcd Phone Menus
“Proxy”. VIP-150T 5. After pressing the PSTN button, the “Proxy” or “P2P” will be replaced by “PSTN”. Please notice that user must plug PSTN line in RJ-11 port when VIP-150T is in PSTN PLANET VIP-150T User’s Manual LCD Phone menus... -
Page 11: Lcd Menu Configuration
(1) Missed Calls：to see all missed calls in message box. (2) Received Calls：to see all received calls in message box. (3) Dialed calls: to see all dialed calls in message box. PLANET VIP-150T User’s Manual 10:10:10 AM... - Page 12 B. Deactivate Deactivate No Response Forward function. (3) Unconditional It is included the above two types. Whether the VIP-150T is in which status, calls will be automatically forwarded to the assigned phone number. A. Activate Enter a forwarded phone number to activate Unconditional Forward function.
- Page 13 User can adjust ring volume by press ç or è on the keypad to decrease or increase ringer volume. Style There are three tone styles for VIP-150T. Move the “>” symbol by press ç or è on the keypad to select the tone style preferred, then press OK to confirm 5. Network Information User can press ç...
- Page 14 VIP-150T won’t reboot and keep trying to connect. SNTP Configuration (1) SNTP Mode: User can set SNTP function to be on or off, which means VIP-150T will capture current time from SNTP server or not. (2) SNTP Server: User can specify a SNTP server for VIP-150T to capture current time.
- Page 15 Set expire time of registration, in the duration of 2/3 expire time, VIP-150T will re-register to Proxy Server again. (3) User Info A. User Name Set User Name of VIP-150T to register to Proxy Server. If Proxy server doesn’t request specific User name, please enter Line number here. B. Line Number Set Line Number of VIP-150T to register to Proxy Server.
- Page 16 LCD Menu Password Set entry password of phone LCD menu. 7. Reboot Reboot machine. It is necessary and important for user to reboot VIP-150T after any configurations has been made. VIP-150T will ask user again before reboot. PLANET VIP-150T User’s Manual...
-
Page 17: Chapter 3 Configuring The Vip-150T Through Web
Step 1. Browse the IP Address predefined via Keypad Please enter IP address (user have to set via LCD menu first) of VIP-150T in web browser. If user failed to set IP address via LCD menu, the default IP address of VIP-150T is 192.168.0.1, user can try to connect to VIP-150T via this default IP via web interface. -
Page 18: Step 3. Enter The Web Interface Main Screen
Most important items are Network Peer-to-Peer mode). Please remember to configure these commands before start to work with VIP-150T. After change any settings, please remember to reboot VIP-150T so that changes can take effect. Note: PLANET VIP-150T User’s Manual Interface,... -
Page 19: Network Interface
When DHCP function enables, VIP-150T will automatically search DHCP server after reboot. 3. PPPoE: If VIP-150T is working with PPPoE connection, user have to set related parameters in “PPPoE Configuration “page. If User set “Get IP mode” as DHCP or PPPoE, IP address, Subnet Mask, and Default routing gateway will become 0.0.0.0 and not allow to be configured. - Page 20 SNTP: Enable / Disable the Simple Network Time Protocol function PLANET VIP-150T User’s Manual...
- Page 21 IP address so that VIP-150T can get correct current time. GMT: Set time zone for SNTP Server time User can set different time zone according to the location of VIP-150T. For example, in Taiwan the time zone should be set as 8,which means GMT+8. IP Sharing: Enable it if VIP-150T is behind IP Sharing router.
-
Page 22: Sip Configurations
Proxy server, please don’t change this value. Phone Book Search: this function, VIP-150T will search dialed number in phone book to see if there is any matched table before send to Proxy server, and if there is a matched data in phone book, VIP-150T will make call to related IP address. - Page 23 VIP-150T to register to the Proxy. Line Account: set user name of VIP-150T for registering. User can set user name and password for registering. If password is no need, please set user name the same as line number or VIP-150T won’t register successfully.
-
Page 24: System Configuration
Interval between Dialstring Digits: To set the duration (in second) of two pressed digits in dial mode as timed out. If after the duration user hasn’t pressed next number, VIP-150T will dial out all number pressed. Terminal Digit: select end of dialing key, e.g. -
Page 25: Pppoe Configuration
VIP-150T still can’t get contact with server, VIP-150T will keep trying to connect. After re-connected, VIP-150T will also restart system. On the other hand, if user disables this function, VIP-150T won’t reboot and keep trying to connect. -
Page 26: Voice Setting
Buffer: Set Min. Delay and Max. Delay of Jitter Buffer for voice packets. Optimized Factor (Jitter): only, please contact with your distributor before making any change. PLANET VIP-150T User’s Manual User can set different packet size for each codec. Set Optimized Factor of voice, this is for advanced user... -
Page 27: Phone Book
User can specify 20 sets of phone book via web interface. Please input index, Name, IP Address and E.164 number of the destination device. Delete Entry: User can delete any configured phone book data by index. PLANET VIP-150T User’s Manual... -
Page 28: Ddns Configuration
On/Off check the host current IP address IP Check Server1: IP Check Server2: Check every: Setting the service delay time (1~59 minutes / 1~24 hours / Off) PLANET VIP-150T User’s Manual Specify IP address check server Specify secondary IP address check server... -
Page 29: Version Information
Please refer to chapter 4.19 [rom] command Boot: Boot loader version VIP-150T Default: This field has no default value. Application: Application image version information of VIP-150T. Default: This field has no default value. DSP Version: DSP image version information. Default: This field has no default value. -
Page 30: Password
Please refer to chapter 4.20 [passwd] command CHANGE: First select login name as root or administrator, then enter current password, new password and confirm new password again to set new password. ABORT: Press abort will clean all inputs. PLANET VIP-150T User’s Manual... -
Page 31: Firmware Upgrade
FTP Login: Set FTP login name and password Target File Type: Select which sector of VIP-150T to upgrade 1. After 2mb file download is finished, all configurations might change to default values, user has to configure again. 2. After upgrade Application, please remember to execute Flash Clean,... -
Page 32: Reboot
11. Reboot Please refer to chapter 4.4 [reboot] command Press reboot will reset VIP-150T. To execute reboot via web browser, VIP-150T will automatically save all data before reboot. To execute reboot via TELNET command. Note: PLANET VIP-150T User’s Manual... -
Page 33: Chapter 4 Configuring The Vip-150T Through Telnet Command Lines
Chapter 4 Configuring the VIP-150T through After setting the IP Address of VIP-150T and reboot, (please refer to LCD Menu: 5-3.4.5), user can enter into Telnet command lines. 1. After user enter VIP-150T configuration via telnet, please use login: ”root”, password: null, press enter to enter command lines. -
Page 34: Debug] Command
4.3 [debug] command This command is for engineers to debug system of VIP-150T. User can add debug flag via command debug –add “debug flags”, and then start debug function via command debug –open. When VIP-150T is working on screen will display related debug messages. -
Page 35: Commit] Command
(pbook –modify “index” name “X” ip “xxx.xxx.xxx.xxx” e164 “X”) 4.6 [commit] command Save any changes after configuring the VIP-150T. 4.7 [ping] command Command ping can test which the IP address is reachable or not. Usage: ping “IP address”... -
Page 36: Time] Command
When User set IP mode to be fixed IP, please set IP, subnet Mask, default gateway as mentioned in item 2. If User set IP mode to be DHCP, VIP-150T will search for DHCP server to capture IP address after reboot. -
Page 37: Pppoe] Command
(GMT-8: ifaddr –timezone -8) 5. -ipsharing: If VIP-150T is behind a IP-sharing , user must enable IP sharing function and specify public IP address.(ifaddr –ipsharing 0/1 “public IP address of IP sharing” , 0 for disable and 1 for enable) Some Proxy servers support endpoint behind NAT function, in this case VIP-150T doesn’t have to enable IP sharing function, please contact with your... -
Page 38: Flash] Command
1. -print: display all current configurations. 2. -idtime: set the duration(in second) of two pressed digits in dial mode as timed out. If after the duration user hasn’t pressed next number, VIP-150T will dial out all number pressed. 3. -keypad: set DTMF type .User can select DTMF type VIP-150T receive and transmit.(sysconf –keypad 0/1 , 0 for in band ,1 for RFC2833.) -
Page 39: Sip] Command
9. –expire: set expire time of registration. VIP-150T will keep re-registering to proxy server before expire timed out. 10. –port: set listening UDP port or VIP-150T. 11. –rtp: set RTP port number. VIP-150T will use this port to send and receive voice. PLANET VIP-150T User’s Manual... -
Page 40: Security] Command
4.14 [security] command 1. –print: display all current configurations. 2. -name: set user ID of VIP-150T for registering. User can set user name and password for registering. If password is no need, please set user name the same as line number or VIP-150T won’t register successfully. - Page 41 711a g711u g729 g729a means VIP-150T can support only one codec or four codecs. 4. -volume: There are three types can be adjustable, voice volume, input gain and DTMF volume. Voice volume means the volume user can hear, input gain means the volume the other side can hear from VIP-150T, DTMF means DTMF transmitting volume.
-
Page 42: Tos] Command
1. This command won’t be functional until network environment can be capable with DSCP function. Note: 2. tos -rtptype 14 -sigtype 10 is top priority of package. PLANET VIP-150T User’s Manual ====> 46 (Decimal System) 010010 ====> 18 (Decimal System) 011010 ====> 26 (Decimal System) 100010 ====>... -
Page 43: Ddns] Command
DDNS server. -checkipsrv: to set IP address of IP address check server. 9. -delay: to set the update interval time. VIP-150T will re-update it’s IP address in this time. (ddns –delay 1-59m/1-24h 10. -force: to force to execute DDNS update. Once user enter this command , VIP-150T will update DDNS data immediately VIP-150T”) -
Page 44: Bureau] Command
8. –method: specify download method to be TFTP or FTP(0 for TFTP.1 for FTP) 9. –ftp: specify user name and password for FTP download method. For example: User prepares to upgrade the latest app rom file – vip150t.100, the TFTP server is 192.168.4.1.1. rom –app –s 192.168.1.1 –f vip150t.100 PLANET VIP-150T User’s Manual... -
Page 45: Passwd] Command
Command rom –print can show current version installed in VIP-150T. 4.20 [passwd] command For security protection, user has to input the password before entering application user/config mode. Two configurations of login name/password are supported by the system. 1. –set: set password of “root” users or “administrator” users. (passwd –set root/administrator “password”) - Page 46 PLANET VIP-150T User’s Manual...
-
Page 47: Chapter 5 Upgrading Software On The Vip-150T
VIP-150T supports three methods to upgrade the new version. All methods are necessary to prepare the TFTP or FTP program on the host PC as TFTP/FTP server. After installing TFTP/FTP program on one PC and connecting to network, VIP-150T is ready to be upgraded. -
Page 48: Web Management
FTP Login: Set FTP login name and password Target File Type: Select which sector of VIP-150T to upgrade 1. After 2mb file download is finished, all configurations might change to default values, user has to configure again. 2. After upgrade Application, please remember to execute Flash Clean,... - Page 49 7. –ftp: specify user name and password for FTP download method. For example: User prepares to upgrade the latest app rom file –vip150t.100, the TFTP server is 192.168.4.1.1. rom –app –s 192.168.1.1 –f vip150t.100 Command rom –print can show current version installed in VIP-150T. PLANET VIP-150T User’s Manual...