Advertisement
Quick Links
Advertisement
Related Manuals for Planet Drawer KVM Console With 17" LCD DKVM-1700
Summary of Contents for Planet Drawer KVM Console With 17" LCD DKVM-1700
- Page 1 Drawer KVM Console With 17” LCD DKVM-1700 Quick Installation Guide...
-
Page 2: Table Of Contents
Before Installation ... 3 Specification ... 4 Packet Contents ... 5 Hardware Installation ... 7 Replace bracket A step (For cabinet depth 828 ~ 1000 mm): ...10 Replace bracket B and C step (For cabinet depth is 504 ~ 614 mm): ...11 Further Configuration ...12 Table of Content... -
Page 3: Before Installation
Thank you for purchasing PLANET DKVM-1700. It is the drawer KVM with single- rail console design offering industrial level input solution, which optimizes your space utilization by controlling your systems in just 1U space on the rack. The separate rail design helps users install the KVM console more easily. You don’t have to prop the heavy console during the installation but just lock the rails into the rack and then pull the KVM console into the rails. With modular design, you can easily integrate different KVM modules to fit your control system. The DKVM-... -
Page 4: Specification
Specification Display Size Panel Type Resolution Capabilities Pixel Pitch Viewing Angle (CR>10) Contrast Ratio Brightness Backlight Supported Colors Response Time Operating System Multi Platform Keyboard Mouse Sync Power Input Power Consumption Temperature Humidity Dimension (W x D X H) Weight Chassis Construction Keyboard Language Certification 17 inches Active Matrix TFT LCD Maximum Resolution up to 1280 x 1024 (SXGA) Supports 0.264 mm x 0.264 mm Right-Left view 60° ~ 70°(Typ) Up-Down View 45° ~ 60°(Typ) 450 : 1 White 250 cd/m2 Four Lamps for Backlight... -
Page 5: Packet Contents
Packet Contents 1. Rail with front and rear bracket x 2 (Please identify the brackets. Right and left sides are different. For cabinet depth 614 ~ 828 mm) 2. Bracket A x 2 (For cabinet depth 828 ~ 1000 mm.) 3. Bracket B x 2 (For cabinet depth 504 ~ 614 mm.) 4. Bracket C x 2 (For cabinet depth 504 ~ 614 mm.) 5. Flat Screw (length = 6 mm) x 6 6. Bracket Screw x 8... - Page 6 7. Key x 2 8. Power Adapter x 1 9. KVM Cable x 1 10. U SB Cable x 1 1. Please check all peripherals according the list before installation. To make sure that the whole unit was not damaged and lost during shipping process. If you encounter any problem, please contact your dealer. 2. Before installation, make sure all peripherals and computer have been turned off. 3. The standard brackets are for 614 ~ 1000 mm (distance means front bracket to rear bracket) cabinet, contact your dealer if you need more longer rear brackets. 4. If your cabinet depth is 828 ~ 1000 mm, please refer “Replace Note bracket A step”. And If your cabinet depth is 504 ~ 614 mm, please refer “Replace bracket B and bracket C step”. 5. Reliable earthing of rack-mounted equipment should be main- tained. Particular attention should be given to supply connections other than direct connections to the branch circuit. 6. The KVM console is a little bit heavy, please prevent this device fall down during the installation. That may make some people hurt and the console will damage.
-
Page 7: Hardware Installation
Hardware Installation 1. Adjust rail until two screws appear. rail two screws 2. Loose (Not remove) seven rear screws. 3. Adjust rail to fit your cabinet... - Page 8 4. Install front and rear bracket on cabinet. 5. Tight seven rear screws up. 6. Repeat step 1~5 for the other side. 7. Push console into rails. (Be careful rear box loose when take out console from carton.)
- Page 9 8. Unlock and pull rail–lock switch (left and right at the same time) then push console to the end. lock unlock rail-lock switch 9. Install three screws (length = 6 mm) in rear of the console. (Both sides) 10. Finish installation as below.
-
Page 10: Replace Bracket A Step (For Cabinet Depth 828 ~ 1000 Mm)
Replace bracket A step (For cabinet depth 828 ~ 1000 mm): 1. Loose (Not remove) seven rear screws. 2. Release six screws. 3. Take rear bracket out. original bracket... -
Page 11: Replace Bracket B And C Step (For Cabinet Depth Is 504 ~ 614 Mm)
4. Adjust rail and input bracket A to rear of the rail then adjust bracket A to fit your cabinet. Install 2~3 screws (don’t tight-up) upon the length you need. One is forbidden. bracket A 5. Repeat step 1 ~ 4 for the other side. 6. Repeat step 3 ~ 10 of install console to finish installation. -
Page 12: Further Configuration
3. Input bracket B to rear of the rail. bracket B 4. Install four screws (don’t tight-up) to combine rail, bracket B and bracket C. bracket C bracket B 5. Repeat step 1 ~ 4 for the other side. 6. Repeat step 3 ~ 10 of install console to finish installation. Further Configuration If you want to configure more detail settings of DKVM-1700, please refer to the user manual in the CD disk.