Advertisement
Recessed
area instructions...
This washer may be installed
in a recessed area or closet.
The installation
dimensions shown
and bottom of door are required.
are the minimum
spaces
Louvered doors with air openings
allowable. Additional
spacing
in top and bottom are
should be considered for ease of
acceptable.
installation
and servicing.
Companion
appliance spacing
If closet door is installed, the
should be considered.
minimum
air openings in top
Minimum
installation
spacing
* Additional
clearances
for wall, door and floor
moldings
may be required.
Hot and cold water
,-*fqucets:
Must be
s
wlthln 122cm (4 feet)
of the back of the
washer and provide
water pressure
34.5-689.6
KPa
(5-100 PSI).
Water
heater:
Set to
deliver 60°C (140°F)
-water
to washer.
Earthed
electrical
outlet
is required. See
"Electrical requirements,"
Panel A.
The hot and cold water
inlets on the back of the
washer have 314 -
11-l I2
American hose coupling
standard threads.
i
7.6cm
T
(3")
i
7.6cm
(3")
0
Support:
Floor must be
sturdy enough to support
washer weight of 143kg
_
Important: Observe all governing
codes and ordinances.
m
closet door
1
43.2cm
(17")
-f-
Level floor:
Maximum
slope under entire washer -
2Scm (1 inch).
155 sq.
(24 sq.
Product
Damage
Do Not store
or operate
washer
below
0°C (32°F)
(some water
may remain
in washer).
See Use & Care Guide for "Winterizing"
information.
Failure
to follow
above
may result
in product
damage.
4
I-
-I
+
Ocm
Ocm
(*O")
('0")
Drain system:
Untape and open washer lid. Remove packages, hoses and literature rack from washer.
1. Laundry
tub drain
system:
2. Floor drain
system:
3. Standpipe
drain
system:
Needs a 76-liter (20-gallon)
laundry tub.
-
Wall
Top of
standpipe
i(ii~inches)
min.
'
jrom end of
72 inches) max.
drain hose to
bottom
of
washer.
from bottom
~
of
wasner.
If a longer drain hose is needed, drain hose extension kit (Part No. 285702) is available from Whirlpool-authorized
parts
distributors.
If drain hose must be shortened,
use kit (Part No. 285442).
Electrical
requirements
Recommended
earthing
method
For your personal safety, this appliance
must be earthed. This appliance is
equipped
with a power supply cord
having an earthing plug.
To minimize possible shock hazard, the
cord must be plugged
into a mating
earthing-type
wall receptacle, earthed in
accordance with local codes and
ordinances.
If a mating wall receptacle is
not available, it is the personal
responsibility
and obligation
of the
customer to have the proper earthed wall
receptacle installed by a qualified
electrician.
See Figure 1 to determine
the
proper mating wall receptacle for the
power supply cord plug equipped
with
this washer.
Electrical
Shock Hazard
l
Electrical
earth
is required
on
l
Do Not have a fuse in the neutral
this appliance.
l
Do Not earth
to a gas pipe.
or earthing
circuit.
A fuse in
l
Do Not modify
the power
supply
the neutral
or earthing
circuit
could
result
in an electrical
cord plug.
If it does not fit the
outlet,
have a proper
outlet
shock.
installed
by a qualified
electrician.
l
Check with
a qualified
l
Do Not use an extension
cord
electrician
if you are in doubt
as
with
this appliance.
to whether
the appliance
is
properly
earthed.
Failure
to follow
these instructions
could
result
in serious
injury
or death.
If codes permit
and a separate
earthing
wire
is used, it is
recommended
that
a qualified
electrician
determine
that
the
earthing
path
is adequate.
Panel A
230-Volts, 4.5 Amps. 50-Hz.
A fused electrical supply is required.
Time-delay fuse or circuit breaker is
recommended.
It is recommended
that a
separate circuit serving only this
appliance be provided.
Figure
1
Advertisement
