Check Before Operating - Husqvarna MS 355 Manual

Hide thumbs

Advertisement

3

Check Before Operating

All Models:
Take into account the working conditions from a
Electric Models Only:
sure that the extension cord length is
sized for the motor used on this saw. See the chart
WARNING: Make sure the unit is connected to
a properly grounded outlet. Failure to comply
with this warning could result in serious bodily
injury or death!
Gasoline Model Only:
Check the engine operation manual.
Oil
ck the Head Platform Assembly (B) with th
engine in a horizontal position, then, check that th
engine oil level is correct. Check the oil level
in the engine operation manual. If the oil level is low
(for normal conditions) as recommended in the
4
Fitting The Blade (Figure 7)
All Models:
blade rotates in a "down-cut" direction. This
that the front of the blade is moving downward
the rear of the blade is moving upward. Mount th
Diamond Blade (DD) so that the arrow on the blad
rotates in this "down-cut" direction. The Diamon
Blade (DD) can be installed / removed by using the
mounting the blade, it should align over the
of the wooden insert in the Conveyor Cart (C). If
is not true, loosen the setscrews that secure the Bear-
n i
g
s
(
H
)
o t
h t
e
H
e
Position the Head Platform Assembly (B) to the left
right until the Diamond Blade (DD) is aligned over
top of the wooden insert, then re-tighten the Bearing
setscrews. During operation of this unit, the blade
and should, pass into the wooden insert, but NOT
18
w.
DO NOT
engine with oil!
W
a
d
P
a l
f t
r o
m
A
s s
e
m
b
y l
(
Electric Models Only:
1. Using the Wrench
2.
3.
Gasoline Model Only:
1. Using the Wrench
2.
) B
(
i
. g
3
. )
5
All Models: (See Figures 5 & 6)
C
or dry. Note that the saw is factory assembled for
operation.
WARNING: Conventional "Wet" diamond
blades MUST be used with water. DO NOT use
conventional "Wet" diamond blades without
water. Using conventional "wet" diamond
blades without water can result in injury or
death of the operator or persons in the work
area!
Warning: Use only Abrasive blades of a
reinforced type.
provided (or one of your own
loosen the Capscrew (BB) by turning it Counter-
CAUTION: Note that on Electric Models the
C
a
p
s
c
e r
w
(
B
B
)
h
a
s
I R
Installation of the wrong capscrew could
damage the blade shaft!
the outer
outer
(CC), the Inner
and arbor shaft (Not Shown) are clean and no
damaged.
the Diamond Blade (DD) to the arbor
install the outer
Capscrew (BB) by turning it in a Clockwis
direction (Right Hand Thread). Use the Wrenc
Always set the Engine Key Switch (VV) to the
"OFF" position BEFORE mounting the blade
provided (or one of your own
loosen the Capscrew (BB) by turning it
CAUTION: Note that on Gasoline Models the
Capscrew (BB) has LEFT HAND THREADS.
Installation of the wrong capscrew could
damage the blade shaft!
the outer
outer
(CC), the Inner
and arbor shaft (Not Shown) are clean and no
damaged.
the Diamond Blade (DD) to the arbor
install the outer
(CC). Install and tighten
Capscrew (BB) by turning it in a Counter-Clockwis
direction
Hand Thread). Use the Wrench
shaft.
Operating Instructions
G
H
T
H
A
N
D
T
H
R
E
A
D
. S
(CC) and make sure
(Not
(CC). Install and tighte
(CC) and make sure
(Not

Hide quick links:

Advertisement

loading

  Also See for Husqvarna MS 355

This manual is also suitable for:

Ms 355g