Speaker Setting; Crossover Network; Channel Level - Pioneer VSX-516 Operating Instructions Manual

Audio/video multi-channel receiver
Table of Contents

Advertisement

Available languages

Available languages

06
The System Setup menu

Speaker setting

Use this setting to specify your speaker
configuration (size, number of speakers).
1
Select SP SET from the SP SETUP menu.
2
Use
to choose the speaker(s) that
you want to set then select a speaker size.
Use
to select the size (and number) of
each of the following speakers:
• Front (F) – Select LARGE if your front
speakers reproduce bass frequencies
effectively, or if you didn't connect a
subwoofer. Select SMALL to send the bass
frequencies to the subwoofer.
• Center (C) – Select LARGE if your center
speaker reproduces bass frequencies
effectively, or select SMALL to send bass
frequencies to the other speakers or
subwoofer. If you didn't connect a center
speaker, choose NO (the center channel is
sent to the front speakers).
• Surround (S) – Select LARGE if your
surround speakers reproduce bass
frequencies effectively. Select SMALL to
send bass frequencies to the other
speakers or subwoofer. If you didn't
connect surround speakers choose NO
(the sound of the surround channels is
sent to the front speakers or a subwoofer).
• Surround Back (SB) – Select the number
and size of surround back speakers you
have. Select LARGE if your surround back
speakers reproduce bass frequencies
effectively. Select SMALL to send bass
frequencies to the other speakers or
subwoofer. If you didn't connect surround
back speakers choose NO.
Note
1 If you select SMALL for the front speakers the subwoofer is fixed to YES. Also, the center, surround, and surround back speak-
ers can't be set to LARGE if the front speakers are set to SMALL. In this case, all bass frequencies are sent to the subwoofer.
2 • If the surround speakers are set to NO, the surround back speakers will automatically be set to NO.
• If you selected SB 2ND Z or SB BIAMP (in Surround back speaker setting on page 27) you can't adjust surround back settings.
• If you select one surround back speaker only, make sure that speaker is hooked up to the left surround back terminal.
3 If you can't get good bass results, listen to the bass response with the subwoofer set to PLUS and YES or the front speakers
set to LARGE and SMALL alternatively and let your ears judge which sounds best. If you're having problems, the easiest option
is to route all the bass sounds to the subwoofer by selecting SMALL for the front speakers.
4 For more on selecting the speaker sizes, see Speaker setting above.
28
En
• Subwoofer (SW) – LFE signals and bass

Crossover network

• Default setting: 100Hz
1
This setting decides the cutoff between bass
sounds playing back from the speakers
selected as LARGE, or the subwoofer, and bass
sounds playing back from those selected as
SMALL.
be for bass sounds in the LFE channel.
1
2
point.
Frequencies below the cutoff point will be sent
to the subwoofer (or LARGE speakers).

Channel level

Using these settings, you can adjust the overall
balance of your speaker system.
1
2
• T. TONE M. – Move the test tone manually
2
frequencies of channels set to SMALL are
output from the subwoofer when YES is
3
Choose the PLUS setting if you
selected.
want the subwoofer to output bass sound
continuously or you want deeper bass (the
bass frequencies that would normally
come out the front and center speakers are
also routed to the subwoofer). If you did not
connect a subwoofer choose NO (the bass
is output from other speakers).
4
It also decides where the cutoff will
Select ' X.OVER' from the SP SETUP menu.
Use
to choose the frequency cutoff
Select CH LEVEL from the SP SETUP menu.
Use
to select a setup option.
from speaker to speaker and adjust
individual channel levels.

Hide quick links:

Advertisement

Table of Contents
loading

This manual is also suitable for:

Vsx-516-k

Table of Contents