Calling Another Handset; Transferring An External Home Call To Another Handset; Three-Party Conference Call; Setting The Dial Mode - Motorola L702BT User Manual

Doc Title : Product Data – User's Guide
Model : Motorola L70×BT

3.21.1 Calling another handset

1. Press <MENU> and then <VOL+> or <REDIAL/VOL-> to select INTERCOM.
2. Press <MENU> and then <VOL+> or <REDIAL/VOL-> to select the handset you want to call.
3. Press <MENU> to call the handset.
4. Press <HOME> to hang up.
NOTE
If the handset is not within the valid operation range, this function may not be available.
During intercom call, you will hear an alert tone if there is an incoming external call. You need to press <HOME> to
hang up the intercom call before answering the incoming external call.

3.21.2 Transferring an external home call to another handset

1. During an external home call, press <MENU>.Your caller is put on hold.
2. Press <VOL+> or <REDIAL/VOL-> to select the handset you want to call.
3. Press <MENU> to call the handset.
4. When the other handset answers by pressing <HOME> or <SPEAKER>, press <HOME> on the calling
handset to transfer the call. If the other handset does not answer, press <MUTE/ CLEAR / BACK/ X > to talk to
your caller again.

3.21.3 Three-party conference call

1. During an external home call, press <MENU>. Your caller is put on hold.
2. Press <VOL+> or <REDIAL/VOL-> to select the handset you want to call.
3. Press <MENU> to call the handset.
4. When the other handset answers the intercom call, press <MENU> on the calling handset to set up the
conference call.
5. Press <HOME> on any handset to hang up three-party conference and leave the other handset in external line
with the caller.

3.22 Setting the dial mode

The default dialing mode is suitable for your country and network operator. It is unlikely that you should need to
change this setting unless advised to do so.
1. Press <MENU> and then <VOL+> or <REDIAL/VOL-> to select SETUP BS.
2. Press <MENU> to select DIAL MODE.
3. Press <MENU> and <VOL+> or <REDIAL/VOL-> to select TONE or PULSE.
4. Press <MENU> to save.
NOTE
If pulse mode is selected, press <*/TONE> to switch from pulse to tone dialing temporarily when dialing out. After
the call is ended, the dial mode will change back to pulse.

3.23 Setting the Flash Time

The default flash time is 600MS. It is unlikely that you should need to change this setting unless advised to do so.
1. Press <MENU> and then <VOL+> or <REDIAL/VOL-> to select SETUP BS.
2. Press <MENU> and then <VOL+> or <REDIAL/VOL-> to select FLASH TIME.
3. Press <MENU> and then <VOL+> or <REDIAL/VOL-> to the flash time you want. (8 options are available: 90,
100, 110, 250, 300, 400, 600 and 700MS)
4. Press <MENU> to save.

3.24 Setting the Area Code

1. Press <MENU> and then <VOL+> or <REDIAL/VOL-> to select SETUP BS.
2. Press <MENU> and then <VOL+> or <REDIAL/VOL-> to select AREA CODE.
3. Press <MENU> and enter the area code.
4. Press <MENU> to save.

3.25 Registration

Up to 5 handsets can be registered to one base. The original handset is pre-registered to use. Additional handsets
must be registered to the base before you can use them.
This document contains confidential and proprietary information of VTech Telecommunications Ltd
Revision :
Page(s) :
R.00
18 of 27