Power Control; Energy Save; No Signal Off (Av Mode Only); No Operation Off (Av Mode Only) - Pioneer PureVision PDP-427XG Operating Instructions Manual

08 Setting up
• Audio from a connected subwoofer is muted when you have
selected "Sub" for "Headphone Output" and connected
headphones.
• To adjust the volume of audio coming from the active (or main)
screen with headphones, select "Main" in step 4 then use
+ / – on the remote.
i i i i i i i i

Power Control

Power Control provides convenient functions for power saving.

Energy Save

You may use one of the three Energy Save modes to save power
consumption.
1 Press HOME MENU.
2 Select "Power Control" (
3 Select "Energy Save" (
4 Select "Save1", "Save 2", or "Picture Off" (
ENTER).
Energy Save
Selections Standard
Save1
Save2
Picture Off
5 Press HOME MENU to exit the menu.
Note
• When you change the Energy Save mode, you may notice a
change in the panel sound. This is normal.

No Signal off (AV mode only)

The system will be automatically placed into the standby mode if no
signal is received for 15 minutes.
1 Press HOME MENU.
2 Select "Power Control" (
3 Select "No Signal off" (
4 Select "Enable" (
No Signal Off
Selections Disable
(default)
Enable
5 Press HOME MENU to exit the menu.
34
En
then ENTER).
then ENTER).
then
Does not decrease the picture brightness.
Slightly lowers power consumption while slightly
suppressing the brightness drop level.
Decreases the picture brightness and lowers
power consumption.
Deactivates the screen to save power. To restore
the screen display, press any button other than
i + /i i i – , i (
i i i FRONT SURROUND) or
e e .
e e
This setting is not memorized by the system.
then ENTER).
then ENTER).
then ENTER).
Does not place the system into the standby
mode.
Places the system into the standby mode if no
signal is received for 15 minutes.
Note
• Five minutes before the system is placed into the standby
mode, a message appears every minute.
• The system may not be placed into the standby mode when
noise signals are present at the plasma display after a TV
program finishes.

No Operation off (AV mode only)

The system will be automatically placed into the standby mode
when no operation is performed for three hours.
1 Press HOME MENU.
2 Select "Power Control" (
3 Select "No Operation off" (
4 Select "Enable" ( then ENTER).
No Operation Off
Selections Disable Does not place the system into the standby
(default) mode.
Enable Places the system into the standby mode if no
operation is performed for three hours.
5 Press HOME MENU to exit the menu.
Note
• Five minutes before the system is placed into the standby
mode, a message appears every minute.

Power Management (PC mode only)

The system will be automatically placed into the standby mode
when no signal is received from the PC.
1 Press HOME MENU.
2 Select "Power Control" (
3 Select "Power Management" (
4 Select "Mode 1" or "Mode 2" (
Power Management
Selections Off (default) No power management
Mode 1 • Places the system into the standby mode when
no signal is received from the personal computer
for eight minutes.
• Even when you start using the computer and a
signal is received again, the system stays off.
• The system is switched on again by pressing
STANDBY/ON on the plasma display or
remote control.
Mode 2 • Places the system into the standby mode when
no signal is received from the personal computer
for eight seconds.
• When you start using the computer and a
signal is input again, the system is switched on.
• The system is switched on again by pressing
STANDBY/ON on the plasma display or
remote control.
5 Press HOME MENU to exit the menu.
then ENTER).
then ENTER).
then ENTER).
then ENTER).
then ENTER).
on the
on the