Setting A Timer Recording - Pioneer DVR-530H-S Operating Instructions Manual

Recording
05
• While the recorder is stopped, you can also use the
number buttons on the remote to select the channel.
(For channel 6, press 6 then ENTER; for channel 24,
press 2, 4 then ENTER)
• If the recorder is stopped, you can also use the +/–
buttons on the front panel to select the channel
number.
3 Use the REC MODE button to set the picture
quality/recording time.
• See Setting the picture quality/recording time on
page 37 for detailed instructions.
4 Use the AUDIO button to select the audio
channel to record.
See Changing audio channels on page 28 for more on
this.
• When recording in VR mode, if a broadcast is
bilingual, both audio channels are recorded, allowing
you to switch the audio channel on playback. The
only exception to this is when the picture quality is set
to LPCM, in which case you do need to select the
audio channel before recording.
5 Press REC to start recording.
If you want to set a recording end time, press the
button repeatedly. The recording time increases in 30
minute increments, up to a maximum of six hours. The
time the recording will end is shown on-screen and in the
front panel display. When the recording ends, the
recorder automatically switches into standby if no other
operation is being performed.
• To cancel the set recording time, press
• If you want to pause recording at any time, press
PAUSE. Press again to restart the recording. (If
recording to the HDD or in VR mode, a new chapter
is started after recording restarts)
6 To stop the recording, press
• If you set the recording time in the previous step, you
can still stop the recording anytime by pressing
STOP REC.
• Recording will stop automatically when there is no
more space on the HDD/DVD, or after 12 hours of
HDD recording (whichever is sooner).
38
En

Setting a timer recording

VR mode
Using the timer recording features you can program up
to 32 timer recordings up to a month in advance. Timer
recording programs can be set to record just once, every
day, or every week.
There are three ways to program a timer recording; using
the Easy Timer Recording feature (see Easy Timer
Recording below), using the G-Code programming
system (see Timer recording using the G-Code™
programming system on page 40), or using manual timer
recording (see Setting a manual timer recording on
page 41).
You can set the recording quality for your timer recording
in the same way as for a regular recording, but with the
added option of an AUTO mode, which maximizes the
recording quality for the space available on the disc (if
recording to DVD), or to fit on to a blank DVD disc (if
recording to HDD).
You can set timer recordings to record to a recordable
DVD or to the hard disk drive. For regular (daily or weekly)
REC
HDD timer recordings that you don't need to keep, you
can use the Auto Replace Recording feature to
automatically replace the previous timer recording with
the new one. Note that when you use this feature, the
previous recording made on that timer program will be
replaced by the next one, regardless of whether you have
watched it yet or not.
REC.
You can also set the recorder so that it will adjust the
recording quality to try and fit the recording on to the disc
if it would not otherwise fit at the recording quality you set
(see Optimized Rec on page 96 for more on this).
Finally, if you set a timer recording to record to DVD but
there isn't a recordable DVD loaded at the time of the
STOP REC.
recording, the Recovery Recording feature will
automatically record the program to the HDD for you.
• A timer recording can't be set if there are already 32
• Timer recording will not start if:
• Timer recording will start when the operation
• If a recordable DVD that doesn't support
Video mode HDD
Important
timer programs waiting to be recorded.
– The recorder is already recording.
– A disc is being initialized, finalized or unfinalized.
preventing timer recording has finished.
simultaneous playback and recording (see
Simultaneous recording and playback on page 45) is
playing when a DVD timer recording is due to start,
playback will automatically stop to allow the
recording to start.